Download Print this page
Westinghouse 6122600 Owner's Manual

Westinghouse 6122600 Owner's Manual

Outdoor lighting fixture

Advertisement

Quick Links

Owner's Manual
Outdoor Lighting Fixture
Installation Instructions
FIXTURE WARRANTY
This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period
of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied.
This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration
of components, nor does it cover damages caused through abuse, improver installation, surges in
electric current, or acts of third parties.
This warranty does not cover the costs of removing and re-installing the lighting fixture.
If this product fails for any reason covered by this warranty, please contact us at www.westinghouse-
lighting.com/contact-us.
ASSEMBLY INSTRUCTIONS FOR OUTDOOR LIGHTING FIXTURE
Congratulations on your Westinghouse purchase. This fixture has been designed to give you many
years of beauty and service. For questions and comments, please visit www.westinghouselighting.
com/contact-us.
NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-
ing materials (see figure 1).
WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.
Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.
Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-
tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-
age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are
damaged, do not install fixture. Return to place of purchase.
For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provid-
ed on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985
have supply wires rated 60° C. Consult a qualified electrician before installing.
FIGURE 1.
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
*OUTLET BOX
CROSS
SCREWS (D)
BAR (B)
MOUNTING
*OUTLET
SCREWS (A)
BOX (C)
*GROUND
WIRE
SIDE
HOLE (G)
GREEN
GROUNDING
SCREW (F)
WIRE
CONNECTORS (E)
MOTION
SENSOR
MOUNTING AND WIRING INSTRUCTIONS
NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures
W-771
meet all UL specifications.
052822
CAUTION: For fixtures labeled for outdoor and wet location use, provide a water-tight seal between
the fixture and the mounting surface by using silicone or similar caulking.
1. Turn off power at circuit box to avoid possible electric shock.
2. Thread mounting screws (A) into cross bar (B) with mounting screws protruding away from outlet
box (C) (see figure 1).
3. Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable).
4. Identify color coding of fixture wires (see figure 2).
5. Connect the black wire from the fixture with the black wire (live wire) from the outlet box (C) by wire
connector (E), and wrap the wire connector (E) with electrical tape for a more secure connection.
6. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box (C) by
wire connector (E), and wrap the wire connector (E) with electrical tape for a more secure connection.
7. Partially thread green grounding screw (F) into side hole (G) of cross bar (B) (see figure 1).
8. Wrap grounding wire from fixture around green grounding screw stem (F) leaving enough excess
wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet
box (C) by wire connector (E) (if applicable), then wrap the wire connector (E) with electrical tape
for a more secure connection.
9. Tighten grounding screw (F). Do not over tighten.
10. Tuck wires inside outlet box (C).
FIXTURE ASSEMBLY INSTRUCTIONS
1. Place back plate (H) over mounting screws (A).
2. Secure into place with cap nuts (I) and rubber washer (K).
3. Install lamp(s). Do not exceed recommended wattage.
4. Turn on power at circuit box.
MOTION SENSOR OPERATION
1. There are 2 switches to set up the fixture: Sensitivity and Timer.
2. Sensitivity: Three sensitivity distance range settings (H,M,L). Highest setting is 30FT/9M. Medium is
20FT/6M and the lowest at 10FT/3M.
3. Sensing angle 220 degree +0/-20 degree.
4. Timer: In the Dusk to Dawn mode: fixture will turn on after the sun has set and switch off when the
sun rises.
5. Timer Switch positions: 2 minutes and 6 minutes. During nighttime, any movement within the
coverage area, will cause the light to turn on. After movement has stopped, the light will remain
on for the preset time limit (2 or 6 minutes).
6. Test mode will allow you to select the preferred sensitivity level. After selecting the desired level.
Walk through the coverage area. When the light turns on, note your distance from the fixture. Try
different approaches toward the fixture from various angles. Try pathways where you expect high
traffic, such as walkways and driveways. Wait 5 seconds before changing to the next level for testing.
FIGURE 2.
FIXTURE
WIRES:
Black
BACK
PLATE (H)
HOUSE
WIRES:
Black
(Hot)
RUBBER
WASHER (K)
WARNING
Turn off electricity to the mounting site before beginning installation.
CAP
Mounting instructions must be followed exactly as shown for the fixture to be safely supported.
NUTS (I)
CLEANING AND CARE
To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can
discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to
clean this fixture.
ORDERING PARTS
Keep this manual for future reference, and in case replacement parts are needed. Available parts can
be ordered from place of purchase. Use exact wording from diagrams when ordering parts.
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
and Westinghouse are trademarks of Westinghouse Electric Corporation.
*NOT SUPPLIED
Used under license by Westinghouse Lighting.
FIXTURE
FIXTURE
WIRES:
WIRES:
White
Bare
Copper
(Ground)
HOUSE
HOUSE
WIRES:
WIRES:
White
Bare
(Neutral)
Copper
(Ground)
www.westinghouselighting.com
All Rights Reserved.
Guide d'utilisation
Instructions d'installation
Appareil d' é clairage pour utilisation extérieure
GARANTIE LIMITÉE DE CINQ ANS
Ce luminaire Westinghouse est garanti pièces et main-d'oeuvre pour une période de Cinq ans à compter
de la date d'achat. Cette garantie remplace toute autre garantie, explicite ou implicite.
Cette garantie ne couvre pas les phénomènes naturels comme les dommages de la foudre, ni la corro-
sion ou la décoloration des composants, pas plus qu'elle ne couvre les dommages causés par les abus,
une installation inappropriée, les surtensions électriques ou les actes de tiers.
Cette garantie ne couvre pas les coûts de dépose et de pose du luminaire.
En cas de défaillance du produit, pour une raison quelconque, couverte par cette garantie, veuillez
nous contacter via www.westinghouselighting.com/contact-us.
LES INSTRUCTIONS D'ASSEMBLAGE DE L'APPAREIL D'ÉCLAIRAGE POUR UTILISATION EXTÉRIEURE
Félicitations ! Vous avez acheté un produit de Westinghouse Lighting. Cet appareil d'éclairage a été
conçu pour durer de nombreuses années. Si vous avez des questions ou des commentaires à
nous communiquer, veuillez visiter www.westinghouselighting.com/contact-us.
NOTA: Déballez soigneusement l'appareil d'éclairage et les pièces. Assurez-vous que toutes les pièces
y sont avant de mettre l'emballage au rebut (voir fig. 1).
MISE EN GARDE: L'ÉLECTROCUTION POURRAIT CAUSER DE GRAVES BLESSURES PERSONNELLES.
Lisez ces instructions et suivez-les exactement comme illustré. En cas de doute, ne commencez
pas l'installation. Consultez un électricien qualifié. Lisez toutes les instructions avant de com-
mencer l'installation. Un câblage approprié est essentiel au bon fonctionnement de cet appareil
d'éclairage. Lorsque vous faites une entaille ou que vous percez un trou dans un mur ou un
plafond, n'endommagez pas les câbles électriques, les canalisations de gaz ou d'eau. Si l'un des
composants de raccordement ou de l'appareil d'éclairage est endommagé, n'installez pas cet
appareil d'éclairage. Retournez-le à l'endroit où vous l'avez acheté.
Convient uniquement aux appareils comportant un avertissement indiquant que l'appareil
d'éclairage est doté d'un fil supportant une chaleur de 75°C ou 90°C. (Ces avertissements se
trouvent sur l'étiquette U.L. et sur l'emballage de l'appareil d'éclairage.)
FIGURE 1.
Il est possible que le dessin illustré ici ne soit pas la reproduction exacte de l'appareil
d'éclairage contenu dans la boîte.
Les instructions d'installation demeurent cependant valables.
*VIS DE LA BOITE DE
SORTIE DE COURANT (D)
BARRE
TRANSVERSALE (B)
*BOITE DE SORTIE
DE COURANT (C)
*FIL DE MISE
A LA TERRE
TROU
LATERAL (G)
VIS DE MISE
A LA TERRE
(VERTE) (F)
CONNECTEURS
DE FIL (E)
CAPTEUR DE
MOUVEMENT
Made in China
PLAQUE
VIS DE
ARRIERE (H)
FIXATION (A)
RONDELLE EN
CAOTCHOUC (K)
ECROUS
CAPUCHONS (I)
*NON FOURNI

Advertisement

loading

Summary of Contents for Westinghouse 6122600

  • Page 1 8. Wrap grounding wire from fixture around green grounding screw stem (F) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet Ce luminaire Westinghouse est garanti pièces et main-d’oeuvre pour une période de Cinq ans à compter FIXTURE WARRANTY box (C) by wire connector (E) (if applicable), then wrap the wire connector (E) with electrical tape de la date d’achat.
  • Page 2 (E) avec du ruban isolant. conexión más segura. Este accesorio de Westinghouse lighting está garantizado frente a defectos de material y de mano de 6. Connectez le fil blanc de l’appareil d’éclairage au fil blanc (fil compensateur) de la boîte de sortie de 6.

This manual is also suitable for:

6120600