Traxxas 7285A Instructions

1/16 Summit LED Light Kit Instructions
Note: Ensure vehicle battery is unplugged before beginning installation. Retain and reuse all parts and fasteners (unless otherwise noted).
Your motor and electronic speed control (ESC) may differ slightly from the one shown in the illustrations.
Kit Contents:
1. LED lighting module
(included with part(s)
#7285A and 7286A only)
2. Power tap
3. LED harness (chassis)
4. LED harness (body)
5. Body light bar
6. Rear light bar
7. Zip ties (6)
8. Zip tie mounts (2)
Tools Needed:
• 2.5mm hex driver • 2.0mm hex driver • 1.5mm hex driver • Body reamer
• Wire cutter (to trim zip tie excess)
Tip: Sort the hardware by assembly as you remove them so you can easily
locate the correct hardware during reinstallation (A).
A A
Remove These Parts to Allow Installation of the
Front
bumper
Servo guard / cover plate
(retain hardware)
Chassis installation
1. Remove the parts shown in Fig. A.
2. Install the LED lighting module
and route the wires through the
loop guide (B).
3. Snap the 4-LED end of the LED
harness (chassis) into the front
light bar and front bumper.
Route the wires against the
front bumper and secure the
wires to the bumper loop with
a zip tie (trim excess) (C).
D - Wiring Diagram D - Wiring Diagram D D
Zip tie
6
5
8
4
7
1
2
LED Light Kit
ESC
Motor
Gear cover
Receiver box cover
and wire clamp
B B
Loop guide Loop guide
LED lighting module LED lighting module
Zip tie
Receiver box
(
Receiver box cover and
wire clamp removed from the wiring lay-out for clarity)
C C
Front light bar Front light bar
LED harness LED harness
3
4. Continue to route the LED harness down the center of the chassis as
shown in (D). Reinstall the front bumper; then, plug the LED harness
connector into the LED lighting module. Route the module wires and
the LED harness around the transmission and secure them with a zip
tie (trim excess) (D).
5. Fully loosen the two rear shock mount
screws, raise the rear shock mount
slightly, and route the 2-LED end of
the harness under the shock mount
(between the shocks), as shown. (D)
Tighten the rear shock mount screws;
then, continue routing the LED harness
toward the rear bumper.
CAUTION: Do not pinch the wiring
between the shock mount and the chassis.
6. Snap the LEDs into the rear bumper.
Route the wires against the rear bumper,
Rear
then, reinstall the rear bumper (E). Plug
bumper
the LED harness connector into the LED
lighting module.
Blank
7. Thread the red wire from the LED
LEDs
lighting module through the opening
in the receiver box cover and plug the
connector into any available channel in
the receiver box (D, F).
Note: If you install the included power
tap, the red female connector from the
power tap can be used to connect the
temperature/voltage sensor
(part #6523, sold separately)
to the ESC.*
8. Reinstall the ESC, the receiver
box cover, the wire clamp,
the motor, and the gear
cover. Plug the black wire
(red female connector) from
the LED lighting module
into the black wire (red male
connector) from the ESC (G).
Note: Ensure that the blue o-ring is properly seated in the groove around the
receiver box cover base. Check for proper adjustment of the gear mesh. Refer to
the vehicle Owner's Manual for detailed instructions.
High-Current Connector
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
Covers Part(s) #7285A, 7286A, 7287, 7288
Wires in strain relief Wires in strain relief
of LED holder of LED holder
Front bumper Front bumper
Bumper Bumper
loop loop
E E
F F
Receiver box Receiver box
cover cover
G G
Connector Connector
from ESC from ESC
Zip tie
Zip tie Zip tie
LED harness LED harness
Rear bumper Rear bumper
Blue o-ring Blue o-ring
Connector from Connector from
LED lighting LED lighting
module module