LG SJ2 - Wireless Sound Bar Simple Manual

Also See for SJ2:

Service manual (55 pages)

Owner's manual (29 pages)

Simple manual (4 pages)

Table of Contents

Contents

1 Introduction
2 Front Panel
3 Rear Panel
4 Subwoofer Connection
5 TV Connection
6 Additional Information
7 Remote control
8 Documents / Resources
- 8.1 References
- 8.2 Download manual

LG SJ2 - Wireless Sound Bar Simple Manual

Introduction

Please read this manual carefully before operating your set and retain it for future reference.
To view the instructions of advanced features, visit http://www.lg.com and then download Owner's Manual.
Some of the content in this manual may differ from your unit.

Front Panel

The buttons are located on the rear.
Front Panel
- Standby
- Selects Function.
- Adjusts Volume.

Rear Panel

(USB) - Connect to a USB device.
PORT. IN (Portable) - Connect to a Portable device.
OPT. IN (Optical) - Connect to an Optical device.

Subwoofer Connection

Place the wireless subwoofer near the sound bar and follow steps below.

Connect the power cord of the sound bar and the wireless subwoofer to the outlet.
Turn on the sound bar.
The sound bar and wireless subwoofer will be automatically connected. The subwoofer's green LED turns on.

Manual Subwoofer Connection
If the subwoofer does not make sound, try to connect manually.

Press Pairing button on the rear of the wireless subwoofer.
- The green LED on the rear of the wireless subwoofer blinks quickly.
  (If the green LED does not blink, press and hold the Pairing button.)
Turn on the sound bar.
Pairing is completed.
- The green LED on the rear of the wireless subwoofer turns on.

warning Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.
To prevent wireless interference

TV Connection

Connect the sound bar to the TV using an Optical cable.
Set up [External Speaker (Optical)] on your TV setting menu.

Additional Device Connection

Connect to the external device as follows.
Set the input source by pressing OPTICAL on the remote control or pressing F repeatedly.

Additional Information

Specification

Power requirements	Refer to the main label.
Power consumption	Refer to the main label.
Dimensions (W x H x D)	Approx. 660.0 mm x 56.0 mm x 99.0 mm (26.0 inch x 2.2 inch x 3.9 inch) With foot
Bus Power Supply (USB)	5 V 500 mA
Amplifier (Total RMS Output power)	160 W RMS

Design and specifications are subject to change without notice.

Remote control

Remote control
STANDARD/BASS BLAST: Selects the sound effect.
DRC ON/OFF : Dynamic Range Control optimizes the volume level of compatible Dolby Digital content.
WOOFER LEVEL : Adjusts the volume level of subwoofer.
AUTO POWER ON/OFF: Automatically turns on by an input source.

Replacement of battery

About Ferrite Core (Optional)

Wind power cord cable around the ferrite core twice.

Industry Canada Statement
[For having wireless function (WLAN, Bluetooth,...)] This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s).
Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3 (B)/NMB-3 (B)
IC Radiation Exposure Statement
[For having wireless function (WLAN, Bluetooth,...)]
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm (7.8 inches) between the antenna & your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

[For product having the wireless function using 5 GHz frequency bands]

the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits as appropriate; and
[for devices operating in the band 5250-5350 MHz having an e.i.r.p. greater than 200 mW] antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 of RSS-247 shall be clearly indicated.

Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.