Indesit YT M10 71 R UK Quick Manual

Quick guide
THANK YOU FOR BUYING AN INDESIT PRODUCT.
In order to receive a more complete assistance, please
register your product on www.indesit.eu/register
CONTROL PANEL
ON/OFF button (hold for Reset)
1
Programme selection knob
2
Start/Pause button (Start: button lights up
3
solidly. Pause: button blinks)
Push & Go
4
Options buttons*
Dryness level
5
Timed drying
6
Start delay
7
Light drying
8
Crease care (hold for Key)
9
Cycle end
10
INDICATORS
Dryness level: Iron dry -
Cycle phase: Dry - Cool tumble - END End of cycle
Empty water tank
Failure: Call after sales service -
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is properly fixed,
either to the dryers's water tank or to the domestic sewage
system.
The dryer must be installed in a room with a temperature
ranging between 5°C and 35°C to ensure proper operation.
Before you use your dryer ensure that it has been in a upright
position for at least 6 hours.
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your filters after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter. Do not load items that are
dripping wet. Do not tumble dry large, very bulky items.
3. Close the door.
4. Press the "On/Off" button.
5. Select the most suitable programme for the type of fabric in that
load.
6. Select the options, if necessary.
7. Press the "Start/Pause" button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
9. Turn the machine off by pressing the "On/Off" button, open the
door and pull the clothing out. If the machine is not switched off
manually, after about a quarter of an hour from the end of the
cycle , the appliance turns off automatically to save energy.
Note that some programme/option accords with "Crease Care"
system. This means that for some hours, after the end of the
drying cycle, the drum rotates at regular intervals to prevent the
formation of creases.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
Hanger dry - Cupboard dry -
Clean door filter - Clean bottom filter
DEMO Demo mode Refer to troubleshooting section
Before using the appliance carefully read the Safety
Instructions.
2
*Note: some models may have the wording in full instead of the icons.
+
Extra dry
PUSH & GO
This function serves to start a cycle, after machine switching on,
without enabling any further button an/or knob (the programme
PUSH & GO will be deactivated instead).
It is always necessary to follow the points 1, 2, and 3 concerning
the daily use.
To start the cycle PUSH & GO, keep the button pressed. The light on
signals that the cycle is started. The cycle is suitable for cotton and
synthetic textiles. Max. load 4 kg. (Cycle duration 110')
If the door is opened during the cycle, to restart it, close the door and
press the button START/PAUSE. This programme does not allow to set
other options.
OPENING OF THE DOOR DURING THE CYCLE
Laundry can be checked while the drying cycle runs and any
garments already dry can be removed, while drying continues for
the remaining items. After closing the door, press the "Start/Pause"
button to resume machine operation.
Keep the door closed until the cycle end to save time and energy.
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the fi rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
8
DEMO
5 6 7
EN
10 1
9 4
3''
3
8