Maintenance; General; Daily Cleaning; Replacing Display Light Bulbs - Hatco GRBW Series Installation And Operating Manual

MAINTENANCE

General

Hatco Glo-Ray Buffet Warmers are designed for maximum
®
durability and performance, with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not "jet-proof" construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
This unit has no "user-serviceable" parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
414-671-6350.

Daily Cleaning

To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
Submerging or saturating unit with water will damage unit
and void product warranty.
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing off.
IMPORTANT—DO NOT use paper towel or glass cleaner to
clean plastic surfaces such as sneeze guards and flip-up
doors. Paper towel and glass cleaner may scratch the
material. Wipe off plastic surfaces using a soft, clean, and
damp cloth.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Wipe down all exterior and interior surfaces using a damp
cloth. A non-abrasive cleaner may be used for difficult
stains. Hard to reach areas should be cleaned using small
brush and mild soap.
3. Clean the plastic sneeze guards, side panels, and front
enclosure using a mild, soapy water solution and a damp,
soft cloth. NOTICE: DO NOT use paper towel or glass
cleaner.

Replacing Display Light Bulbs

Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display lights are incandescent light bulbs that illuminate
the warming area. Each bulb has a special coating to guard
against injury and food contamination in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant light bulbs meet NSF
standards for food holding and display areas. For
120 V applications, use Hatco P/N 02.30.265.00. For
220, 240, 220–230, and 230–240 V, use Hatco P/N
02.30.266.00.
NOTE: Shatter-resistant halogen bulbs are available in place
of the standard incandescent bulbs. Halogen bulbs
have a special coating to guard against injury and food
contamination in the event of breakage. For 120 V
applications, use Hatco P/N 02.30.081.00. For 220, 240,
220–230, and 230–240 V applications use Hatco P/N
02.30.082.00.
ELECTRIC SHOCK HAZARD: Use only Genuine Hatco
Replacement Parts when service is required. Failure to use
Genuine Hatco Replacement Parts will void all warranties
and may subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to operate
safely in the environments in which they are used. Some
aftermarket or generic replacement parts do not have the
characteristics that will allow them to operate safely in
Hatco equipment.
10
English
WARNING
WARNING
GRBWM-1122