Advertisement
Quick Links
Advertisement
Summary of Contents for Bullmer A200-2
- Page 1 Ink jet plotter --Operating manual...
- Page 2 Foreword Thank you for choosing an inkjet plotter. Inkjet plotter using a Hewlett-Packard CAD Special nozzle technology, with high speed and precision, stable characteristics, up to 600DPI resolution;Inkjet plotter supporting the "Drawing Management Center" software that can draw HPGL format files from a variety of software, such as love Lancaster.OPTITEX.Bo.
- Page 3 Catalogue Chapter one Safety Tips Chapter II Use matters needing attention 2.1 the use of the machine environment 2.2 other considerations Chapter III Brief introduction 3.1 the basic introduction 3.2 parts and their functions Chapter fourth Installation 4.1 the installation of the machine 4.2 the connection 4.3 the paper Chapter five Inkjet plotter Center Software Description...
-
Page 4: Safety Tips
Chapter one Safety Tips Please read carefully before using this ink jet plotter all of the following guidelines: *Ink jet plotter on level ground, to avoid unnecessary failure caused by not smooth plane. *Please use the rated voltage (220V), not to inkjet plotter is connected to the accessory no rated voltage, power supply instability will lead to performance degradation plotter, plotter or even destroy the power board. - Page 5 *Do not use damaged or worn on the power line. * Don't put inside the liquid drip into the plotter, otherwise it will cause the components from the damage of circuit board short circuit of the machine. *Don't try to lubricating the moving parts of the machine. *Unless the machine instructions are on the "use manual", otherwise please don't repair or remove the plotter.
- Page 6 Chapter II Use matters needing attention Although you are very familiar with inkjet plotter, but before operating this machine also please read the following precautions: the use of the machine environment Plotter work and storage temperature range is: 15 to 35 degrees Celsius, not in the glare, radiation or heat storage or use of this machine.Plotter work at room temperature humidity range is: 20% - 20%, do not use in wet or humid and dusty places plotter, because once the moisture condensation inside the machine,...
-
Page 7: Brief Introduction
- 50% of the drawing production, and can accurately automatically judge shows status information using HP original HP51645 nozzle, free maintenance, high resolution, low use cost 3.1 the basic performance indicators Model A200-2 A220-2 A240-2 A240-4 Maximum width on... - Page 8 3.2 parts and their functions： （1）control panel （2）The cartridge group （3）HP ink box （4）pinch roller （5）Paper roll grinding wheel （6） Paper roll （7） Began to collect paper sensor （8） Stop paper sensor （9） Feed roller （10） protective cover （11） power switch （12）...
-
Page 9: Installation
Chapter fourth Installation 4.1 the installation of the machine 4.4.1 check the goods before installation This machine consists of the following items: host, support group (including the left and right sides, around the base, beam), the power cord, USB cable, HP cartridges, paper feeding roller, the pressure rod, screw, hex socket wrench. - Page 10 4.1.2 installation host and support With reference to the above group around the beam with socket head cap screw and bracket connected, and then the host on the bracket, at the same time take the host and the bracket in inner hexagon spanner, again according to the logo connecting line the good joint.
- Page 11 Chapter five Instructions on the use of the ink jet plotter center software Inkjet plotter drawing center software, can draw from a variety of software *. PLT file, such as love, OPTITEX. G. Rick, etc., and can accurately and automatically judgment and display will be drawing time; Has the intelligence and automation of the ink head cleaning technology.
- Page 12 2、 Language function switch: the software supports. The English version, in the language selection in the parameter Settings are free to switch(figure 2)。 （figure 2） 3、 File to import, click the file to import files or toolbar (figure 3), choose to print *.
- Page 13 (figure 3） （figure 4）...
- Page 14 （figure 5） 4、 Parameter Settings: the directory in the preferences in the menu bar user preferences in parameter Settings. The system parameter Settings, and other three options, according to the file will print to parameter setting, can print documents（figure 6、7、8、9） 。 （figure 6）...
- Page 15 （figure 8） （figure 9） 5、 After drawing: click to choose the file to print, click start printing and sure, plotter will draw this file, and in the process of drawing the workspace and the status bar will clearly reflect the process of drawing(figure 10.figure 11)。 （figure 10）...
- Page 16 （figure 11）...