Table of Contents
Advertisement
Quick Links
30", 36" AND 48" (76.2 CM, 91.4 CM AND 121.9 CM)
COMMERCIAL STYLE WALL-MOUNT CANOPY
For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230
HOTTE DE CUISINIÈRE POUR MONTAGE
Instructions d'installation et Guide d'utilisation et d'entretien
Table of Contents/Table des matières............................................................................. 2
IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
FOR RESIDENTIAL USE ONLY.
IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.
POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.
LI3ZAB/W11374532A
RANGE HOOD
Installation Instructions and Use & Care Guide
or visit our website at www.kitchenaid.com
In Canada, for assistance, installation and service, call: 1-800-807-6777
or visit our website at www.kitchenaid.ca
MURAL 30", 36" ET 48" (76,2 CM,
91,4 CM ET 121,9 CM)
Au Canada, pour assistance, installation ou service composez le 1-800-807-6777
ou visitez notre site web à www.kitchenaid.ca
Advertisement
Table of Contents
Related Manuals for KitchenAid KVWC906JSS0
Summary of Contents for KitchenAid KVWC906JSS0
- Page 1 91,4 CM ET 121,9 CM) Instructions d’installation et Guide d’utilisation et d’entretien Au Canada, pour assistance, installation ou service composez le 1-800-807-6777 ou visitez notre site web à www.kitchenaid.ca Table of Contents/Table des matières................2 IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE DES MATIÈRES RANGE HOOD SAFETY ..............2 SÉCURITÉ DE LA HOTTE DE CUISINIÈRE .......19 INSTALLATION REQUIREMENTS ..........3 EXIGENCES D'INSTALLATION ...........21 Tools and Parts ................3 Outillage et pièces..............21 Location Requirements..............4 Exigences d'emplacement............21 Venting Requirements..............5 Exigences concernant l'évacuation ...........23 Electrical Requirements ...............6 Spéci cations électriques ............24 INSTALLATION INSTRUCTIONS ..........7... -
Page 3: Installation Requirements
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF A RANGE TOP WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC GREASE FIRE: SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may Use this unit only in the manner intended by the ignite. -
Page 4: Location Requirements
Parts needed Product Dimensions Home power supply cable 1 - ½" (12.7 mm) UL listed or CSA approved strain relief Front view 3 UL listed wire connectors 18¹⁄ " (45.9 cm) for 48" (121.9 cm) Hood 1 wall or roof cap 12¹⁄... -
Page 5: Venting Requirements
Installation Dimensions The vent system must have a damper. If the roof or wall cap has a damper, do not use the damper supplied with the range 30" (76.2 cm), 36" (91.4 cm), hood. or 48" (121.9 cm) cabinet opening width Use caulking to seal exterior wall or roof opening around the (If installed between cabinets) cap. -
Page 6: Electrical Requirements
Typical In-line Blower Motor System Venting Installations Electrical Requirements Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. -
Page 7: Installation Instructions
INSTALLATION INSTRUCTIONS Prepare Location It is recommended that the vent system be installed before range hood is installed. If you are installing the optional backsplash, follow the instructions included with that product. Before making cutouts, make sure there is proper clearance 15³⁄₈"... -
Page 8: Install Range Hood
6. Remove terminal box cover and set aside. Install Range Hood Internal Blower Motor 7. Remove knockout from the back of the range hood and install a UL listed or CSA approved ¹⁄₂" (1.3 cm) strain relief. NOTE: Your range hood requires you to purchase either an 8. - Page 9 4. Install the 6 mm nuts to the outside top or outside back Dual Blower Motor Assembly (alternate location on some models) of the range hood at the proper location for the selected motor system. Two 6 mm nuts are required for the single motor system. Clip nuts into the small square notches located at the left and right end of the square vent opening.
-
Page 10: Install Range Hood In-Line (External Type) Blower Motor
4. Push the right end of the motor mounting plate up and snap it into the spring tab. Install Range Hood In-Line (External Type) NOTE: The spring tab should be outside the slot in the Blower Motor mounting plate. NOTE: Your range hood requires you to purchase either an internal type or an in-line (external type) blower motor system. - Page 11 Install In-line Blower System Complete Preparation NOTE: The blower motor housing can be mounted using 4 holes 1. Determine and make all necessary cuts for the vent system. from either the inlet side or the outlet side of the blower. IMPORTANT: When cutting or drilling into the ceiling or wall, do not damage electrical wiring or other hidden utilities.
-
Page 12: Make Electrical Connections For In-Line Blower Motor System
Make Electrical Connections for In-Line Blower Motor System WARNING WARNING Electrical Shock Hazard Electrical Shock Hazard Disconnect power before servicing. Electrically ground blower. Replace all parts and panels before operating. Connect ground wire to green and yellow ground wire in terminal box. Failure to do so can result in death or electrical shock. -
Page 13: Make Electrical Power Supply Connection To Range Hood
6. Connect the same color wires to each other (black to black, white to white, etc.) using UL listed wire connectors. NOTE: Connect the green (or green/yellow) ground wire from the wiring conduit to the green (or bare) ground wire from the home power supply using UL listed wire connectors (see the “Make Electrical Power Supply Connections to Range Hood”... -
Page 14: Complete Installation And Check Operation
Complete Installation and Check Operation Range Hood Controls 1. Install grease filters. See “Range Hood Care” section. Operating the light 2. Check operation of the range hood blower and lights. See “Range Hood Use” section. 1. Move the light switch to the “1” position to turn range hood light to night light setting. -
Page 15: Range Hood Care
RANGE HOOD CARE Range Hood Lamps Cleaning IMPORTANT: Clean the hood and grease lters frequently Replacing a LED Lamp according to the following instructions. Replace grease lters before operating hood. Turn off the range hood and allow the LED lamp to cool. To Exterior surfaces: avoid damage or decreasing the life of the new bulb, do not To avoid damage to the exterior surface,do not use steel wool or... -
Page 16: Wiring Diagram
WIRING DIAGRAM Junction box N L Gnd SE112B Fan speed Fan speed Fan speed Light Speed 1 Temperature Closure Speed 2 sensor temperature: 167˚F±5.4˚F Speed 3 (75+/-3˚C) Opening temperature: ≥140˚F (60˚C) 25uF 25uF 9 10 Optional kit with 1 motor Lamps Motor Resistance (Ohms) Motor Characteristics... -
Page 17: Assistance Or Service
Order Part Number W10352736 for 36" (91.4 cm) model For further assistance Order Part Number W10352735 for 48" (121.9 cm) model If you need further assistance, you can write to KitchenAid with In Canada any questions or concerns at: KitchenAid Brand Home Appliances... - Page 19 06/19 Printed in Mexico /™ ©2019 KitchenAid. Used under license in Canada. All rights reserved. ® LI3ZAB/W11374532A Imprimé au Mexique Utilisé sous licence au Canada. Tous droits réservés.