Instant Wireless ® Series Wireless-G Broadband Router Use this guide to install: WRT54G User Guide...
Page 2
If the product proves defective during this warranty period, go to the Linksys website at www.linksys.com for complete RMA (Return Merchandise Authorization) assistance. You can also call Linksys Technical Support in order to obtain a RMA Number. BE SURE TO HAVE YOUR PROOF OF PURCHASE AND A BARCODE FROM THE PRODUCT’S PACK- AGING ON HAND WHEN CALLING.
73/23/EEC oleellisten vaatimusten ja sitä koskevien näiden direktiivien muiden ehto- jen mukainen. • Linksys Group déclare que la Instant Wireless® Wireless-G Broadband Router est conforme aux conditions essentielles et aux dispositions relatives à la directive 1999/5/EC, la directive 89/336/EEC, et à la directive 73/23/EEC.
Internet. Configuration is a snap with the web browser-based configuration utility. With the Linksys Wireless-G Broadband Router at the center of your home or office network, you can share a high-speed Internet connection, files, printers, and multi-player games with the flexibility, speed, and security you need! ®...
Features • Compatibility with Draft 802.11g (2.4GHz) and 802.11b (2.4GHz) Standards • Setup Wizard for Easy Installation • Wireless Security with up to 128-bit WEP Encryption • Enhanced Security Management Functions: Internet Access Policies with Time Schedules, Website Blocking, IP and MAC Address Filtering; Port Filtering;...
Dynamic IP Addresses A dynamic IP address is automatically assigned to a device on the network, such as PCs and print servers. These IP addresses are called “dynamic” because they are only temporarily assigned to the PC or device. After a certain time period, they expire and may change.
Chapter 2: Getting to Know the Wireless-G Broadband Router The Router’s Back Panel Figure 2-1 The Router’s ports are located on the Router’s back panel. Internet The Internet port is where you connect your cable or DSL modem through an Ethernet network cable. Your modem connection will not work from any other port.
Page 8
The WLAN Indicators Green. When the Act LED flickers, the wireless network is active. Link Green. When the Link LED is continuously lit, the wireless network is available. The LAN Indicators Link/Act Green. The Link/Act LED serves two purposes. If the LED is continuously lit, the Router is successfully connected to a device through the corresponding port.
Chapter 3: Connect the Router Overview The Router’s setup consists of more than simply plugging hardware together. You will have to configure your networked PCs to accept the IP addresses that the Router assigns them (if applicable), and you will also have to configure the Router with setting(s) provided by your Internet Service Provider (ISP).
4. Power on one of the PCs on your wireless network(s). 5. For initial access to the Router through a wireless connection, make sure the PC’s wireless adapter has its SSID set to linksys (the Router’s default set- ting), and its WEP encryption is disabled. After you have accessed the Router, you can change the Router and this PC’s adapter settings to match...
Configuring Windows 98 and Millennium PCs 1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network icon. 2. On the Configuration tab, select the TCP/IP line for the applicable Ethernet adapter. Do not choose a TCP/IP entry whose name mentions DUN, PPPoE, VPN, or AOL.
Configuring Windows 2000 PCs 1. Click the Start button. Select Settings and click the Control Panel icon. Double-click the Network and Dial-up Connections icon. 2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area Connection listed). Double-click the Local Area Connection.
Configuring Windows XP PCs The following instructions assume you are running Windows XP with the default interface. If you are using the Classic interface (where the icons and menus look like previous Windows versions), please follow the instructions for Windows 2000. 1.
Chapter 5: Configure the Router’s Basic Settings This chapter will show you how to configure the Router to function in your network and gain access to the Internet through your Internet Service Provider (ISP). Detailed description of the Router’s web-based utility can be found in “Chapter 6: The Router’s Web-based Utility.”...
Page 15
Automatic Configuration - DHCP If you are connecting through DHCP or a dynamic IP address from your ISP, perform these steps: A. Keep default setting, Automatic Configuration DHCP, as the Configuration Type. B. Click the Apply button to save the setting, or click the Cancel button to clear the setting and start over.
G-Only. If you want to disable wireless networking, select Disable. B. Customize the SSID and Channel settings as needed. For added security, you should change the default SSID (linksys) to a unique name. Then click the Apply button to save your changes. For more information, refer to “Chapter 6: The Router’s Web-based Utility.”...
Firmware Version This shows the version and date of the firmware you are using. Future versions of the Router’s firmware will be posted and available for download on the Linksys website at www.linksys.com. Time Zone Select the time zone for your location. If your location experiences daylight savings, leave the checkmark in the box next to Automatically adjust clock for daylight saving changes.
Page 18
Static IP If you are required to use a permanent IP address to connect to the Internet, then select Static IP. Figure 6-4 Internet IP Address This is the Router’s IP address, when seen from the WAN, or the Internet. Your ISP will provide you with the IP Address you need to specify here.
Page 19
User Name and Password Enter the User Name and Password provided by your ISP. Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time).
Page 20
Make sure this setting is the same for all devices in your wireless network. For added security, Linksys recommends that you change the default SSID (linksys) to a unique name of your choice. SSID Broadcast When wireless clients survey the local area for wireless net- works to associate with, they will detect the SSID broadcast by the Router.
16 alphanumeric characters. (This Passphrase function is compatible with Linksys wireless products only. If you want to communicate with non-Linksys wireless products, enter the WEP key manually on the non-Linksys wireless products.) After you enter the Passphrase, click the Generate button to create WEP keys.
PPTP - Point-to-Point Tunneling Protocol is the method used to enable VPN sessions to a Windows NT 4.0 or 2000 server. To allow PPTP tunnels to pass through the Router, PPTP Pass-Through is enabled by default. To disable PPTP Pass-Through, uncheck the box next to PPTP. Web Filters Using the Web Filters feature, you may enable up to four specif- ic filtering methods.
Page 23
Router’s set- tings before you upgrade its firmware. To upgrade the Router’s firmware: 1. Download the firmware upgrade file from www.linksys.com, and extract the file using a file archive utility such as WinZip. 2. Click the Upgrade button.
Page 24
To remotely manage the Router, enter http://xxx.xxx.xxx.xxx:8080 (the x’s represent the Router's Internet IP address, and 8080 represents the specified port) in your web browser’s Address field. You will be asked for the Router’s password. After successfully entering the password, you will be able to access the Router’s web-based utility.
DHCP The DHCP screen allows you to configure the settings for the Router’s Dynamic Host Configuration Protocol (DHCP) server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer on your network. Figure 6-13 If you choose to enable the Router’s DHCP server option, you must configure all of your network PCs to connect to a DHCP server (the Router), and make sure...
Status The Status screen displays the Router’s current status and configuration. All information is read-only. Figure 6-15 Note: The information provided and buttons available may vary depending on the Router’s settings. Instant Wireless Series Wireless-G Broadband Router ® Firmware Version The version number of the firmware currently installed is displayed here.
Guide is in Adobe Acrobat Portable Document File (.pdf) format, so you need the Adobe Acrobat Reader to view it. If you do not have the Acrobat Reader, click the Adobe website link to download it. Figure 6-16 Clicking this link will take you to Linksys’s website,...
Advanced Tabs The following instructions are for advanced users or users whose setup needs require special configuration. When you click the Advanced tab, you will be able to set up these features. There are five additional tabs available. Advanced Wireless - Allows you to customize data transmission settings for your wireless network.
Page 29
Transmission Rate The default setting is Auto. The range is from 1 to 54Mbps. The rate of data transmission should be set depending on the speed of your wireless network. You can select from a range of transmission speeds, or keep the default setting, Auto, to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature.
Figure 6-19 For each PC, the list shows—in real time—the Client Host Name, IP Address, MAC Address, and Enable MAC Filter option. To enable the MAC address filter for a specific PC, click its Enable MAC Filter box. To disable the MAC address filter for a specific PC, uncheck its Enable MAC Filter box.
Page 31
Internet Schedule Profile This feature allows you to customize up to ten dif- ferent Internet Access Policies for particular PCs, which are identified by their IP or MAC addresses. For each policy’s designated PCs, during the days and time specified, the Router can do one or more of the following: •...
Summary To see a summary of all the policies, click the Summary button. The Internet Policy Summary screen will show each policy’s Number, Policy Name, Days, and Time of Day. To delete a policy, click its box, and then click the Delete button.
Page 33
The following table shows the typical port forwarding settings for common Internet applications. Application External Port • Telnet • SMTP • TFTP Finger • HTTP • POP3 • NNTP • SNMP Customized Applications In the field provided, enter the name you wish to give each application.
Routing On the Routing screen, you can set the routing mode of the Router. Gateway mode is recommended for most users. Figure 6-25 Note: The Routing screen and available features will vary depending on which mode you select. Operating Mode Choose the correct working mode. Keep the default setting, Gateway, if the Router is hosting your network’s connection to the Internet (recommended for most users).
Show Routing Table Click the Show Routing Table button to view all of the valid dynamic and static route entries in use (see Figure 6-26). The Destination IP address, Subnet Mask, Gateway, and Interface information are displayed for each entry. Click the Refresh button to display the most up-to-date data. Click the Close button to return to the Routing screen.
Router. Read the descrip- tions below to help you solve your problems. If you can’t find an answer here, check the Linksys website at www.linksys.com. 1. I need to set a static IP address on a PC.
Page 37
For Windows 2000: A. Click Start, Settings, and Control Panel. Double-click Network and Dial-Up Connections. B. Right-click the Local Area Connection that is associated with the Ethernet adapter you are using, and select the Properties option. C. In the Components checked are used by this connection box, highlight Internet Protocol (TCP/IP), and click the Properties button.
Page 38
B. Open a command prompt. • For Windows 98 and Me, please click Start and Run. In the Open field, type in command. Press the Enter key or click the OK button. • For Windows NT, 2000, and XP, please click Start and Run. In the Open field, type cmd.
Page 39
IPSec server. Refer to “Problem #7, I need to set up online game hosting or use other Internet applications” for details. Check the Linksys website for more information at www.linksys.com. 6. I need to set up a server behind my Router and make it available to the public.
Page 40
In order to upgrade the firmware with the latest features, you need to go to the Linksys website and download the latest firmware at www.linksys.com. Follow these steps: A. Go to the Linksys website at http://www.linksys.com and download the latest firmware. B. To upgrade the firmware, follow the steps in the System section found in...
Page 41
13. The firmware upgrade failed, and/or the Diag LED is flashing. The upgrade could have failed for a number of reasons. Follow these steps to upgrade the firmware and/or make the Diag LED stop flashing: A. If the firmware upgrade failed, use the TFTP program (it was downloaded along with the firmware).
Does the Router support any operating system other than Windows 95, Windows 98, Windows Millennium, Windows 2000, Windows NT, or Windows XP? Yes, but Linksys does not, at this time, provide technical support for setup, con- figuration or troubleshooting of any non-Windows operating systems.
Page 43
Linksys website, www.linksys.com. How will I be notified of new Router firmware upgrades? All Linksys firmware upgrades are posted on the Linksys website at www.linksys.com, where they can be downloaded for free. To upgrade the Router’s firmware, use the System tab of the Router’s web-based utility. If the Router’s Internet connection is working well, there is no need to download a...
Page 44
How can I check whether I have static or DHCP IP Addresses? Consult your ISP to obtain this information. How do I get mIRC to work with the Router? Under the Port Forwarding tab, set port forwarding to 113 for the PC on which you are using mIRC.
Page 45
How many channels/frequencies are available with the Router? There are eleven available channels, ranging from 1 to 11 (in North America). If your questions are not addressed here, refer to the Linksys website, www.linksys.com.
IP addresses, which are the true addresses on the Internet. For example, www.yahoo.com is 66.218.71.87 (this IP address may change). Type it into your web browser and you will wind up at the Linksys home page every time. There are servers that translate the URL to an IP address;...
WEP encryption has been called 40-bit because it uses a 40-bit secret key along with a 24-bit Initialization Vector (40 + 24 = 64). Wireless vendors may use either name. Linksys uses the term “64-bit” when referring to this level of encryption. All wireless devices compliant with the 802.11b standard will sup- port 64-bit WEP.
Page 48
It is case-sensitive and should not be longer than 16 alphanumeric characters. (This Passphrase function is compatible with Linksys wireless products only. If you want to communicate with non-Linksys wireless prod- ucts, enter the WEP key manually on the non-Linksys wireless products.) After you enter the Passphrase, click the Generate button to create WEP keys.
Appendix D: Finding the MAC Address and IP Address for Your Ethernet Adapter This section describes how to find the MAC address for your Ethernet adapter to do either MAC address filtering or MAC address cloning for the Router and ISP.
802.1g - A proposed, but as yet unratified extension of the IEEE 802.11 stan- dard for wireless networking hardware. The draft 802.11g specifications used by Linksys specify a maximum data transfer rate of 54Mbps using OFDM modulation, an operating frequency of 2.4GHz, backward compatibility with IEEE 802.11b devices, and WEP encryption for security.
Page 51
Auto-negotiate - To automatically determine the correct settings. The term is often used with communications and networking. For example, Ethernet 10/100 cards, hubs, and switches can determine the highest speed of the node they are connected to and adjust their transmission rate accordingly. Backbone –...
Page 52
DDNS (Dynamic Domain Name System) - Allows a network device with a dynamic Internet IP address to have a fixed host and domain name, such as myhostname.mydomainname.com. It is useful when you are hosting your own website, FTP server, or other server behind a router, so people can find your site no matter how often the Internet IP address changes.
Page 53
Fast Ethernet - A 100 Mbps technology based on the 10Base-T Ethernet CSMA/CD network access method. FHSS (Frequency Hopping Spread Spectrum) - FHSS continuously changes (hops) the carrier frequency of a conventional carrier several times per second according to a pseudo-random set of channels. Because a fixed frequency is not used, and only the transmitter and receiver know the hop patterns, interception of FHSS is extremely difficult.
Page 54
a corporation scale, or when it is necessary to connect the wired and wireless networks. IP Address - In the most widely installed level of the Internet Protocol (IP) today, an IP address is a 32-binary digit number that identifies each sender or receiver of information that is sent in packets across the Internet.
Page 55
Passphrase - Used much like a password, a passphrase simplifies the WEP encryption process by automatically generating the WEP encryption keys for Linksys products. PC Card - A credit-card sized removable module that contains memory, I/O, or a hard disk.
Page 56
PCMCIA - The PCMCIA (Personal Computer Memory Card International Association) is an industry group organized in 1989 to promote standards for a credit card-size memory or I/O device that would fit into a personal computer, usually a notebook or laptop computer. Ping (Packet INternet Groper) - An Internet utility used to determine whether a particular IP address is online.
Page 57
SNMP (Simple Network Management Protocol) - A widely used network monitoring and control protocol. Data is passed from SNMP agents, which are hardware and/or software processes reporting activity in each network device (hub, router, bridge, etc.) to the workstation console used to oversee the net- work.
Page 58
TX Rate – Transmission Rate. UDP (User Datagram Protocol) - A method (protocol) used along with the IP (Internet Protocol) to send data in the form of message units (datagram) between network devices over a LAN or WAN. While IP takes care of handling the actual delivery of the data (routing), UDP takes care of keeping track of the individual units of data (called packets) that a message is divided into for effi- cient delivery over the network.
Appendix F: Specifications Standards IEEE 802.3, IEEE 802.3u, IEEE 802.11b, Draft 802.11g Ports Internet: One 10/100 RJ-45 Port for Cable/DSL Modem LAN: Four 10/100 RJ-45 Switched Ports One Power Port Button One Reset Button Cabling Type Category 5 Ethernet Network Cabling or better Transmit Power 15 dBm Modulation...
Wireless-G Broadband Router ® Appendix H: Contact Information For help with the installation or operation of the Wireless-G Broadband Router, contact Linksys Technical Support at one of the phone numbers or Internet addresses below. Sales Information Technical Support RMA (Return Merchandise...