Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Lexmark™ E360
Quick Reference
Loading paper
Loading the standard 250-sheet
tray
The printer has two trays to select from: the standard tray (Tray 1),
also known as the 250-sheet tray, and either the optional
250-sheet tray or the optional 550-sheet tray (Tray 2). Only one
optional drawer (which includes an optional tray) may be attached
to the printer at one time.
Notes:
•
Proper paper loading prevents jams and facilitates
trouble-free printing.
•
Do not remove trays while a job prints or while Busy appears
on the display. Doing so may cause a jam.
1
Pull the tray completely out.
2
Squeeze the width guide tabs on the right guide as shown, and
slide the width guides to the sides of the tray. Notice that the
two width guides move in unison when you move just the right
width guide.
3
Squeeze the length guide tabs together as shown, and slide
the length guide to the correct position for the paper size being
loaded.
If you are loading a longer size of paper like A4 or legal, squeeze
the length guide tab and slide the length guide backwards to
1
the position for the length of paper you are loading. The tray
extends backwards as shown.
If you are loading A6-size paper:
a
Squeeze the length guide tab shown as follows, and slide
the length guide toward the center of the tray to the A5
size position.
b
Raise the A6 backstop.
Note: The standard tray only accommodates 150 sheets of A6
paper. Notice the maximum fill line on the A6 backstop which
indicates the maximum height for loading A6 paper. Do not try to
overload the tray.
Advertisement
Table of Contents
Related Manuals for Lexmark E360dtn
Summary of Contents for Lexmark E360dtn
-
Page 1: Quick Reference
Loading paper Loading the standard 250-sheet tray The printer has two trays to select from: the standard tray (Tray 1), also known as the 250-sheet tray, and either the optional 250-sheet tray or the optional 550-sheet tray (Tray 2). Only one optional drawer (which includes an optional tray) may be attached to the printer at one time. - Page 2 If a different type of paper was loaded than the type previously loaded in the tray, change the Paper Type setting for the tray from the printer control panel. For more information, see “Setting the Paper Size and Paper Type” on page 5.
-
Page 3: Opening The Multipurpose Feeder
550-sheet tray Only one optional drawer, which includes either a 250- or 550-sheet tray, may be attached to the printer at a time. Regardless of the number of sheets in the optional tray, it is referred to as Tray Pull the tray completely out. -
Page 4: Loading The Multipurpose Feeder
Grasp the handle, and pull the extension so it flips forward. Guide the extension down gently so the multipurpose feeder is extended fully and open. Loading the multipurpose feeder Squeeze the tab located on the right width guide, and move the guides out fully. -
Page 5: Setting The Paper Size And Paper Type
Paper should lie flat in the multipurpose feeder. Make sure the paper fits loosely in the multipurpose feeder and is not bent or wrinkled. From the printer control panel, set the Paper Size and Paper Type. Setting the Paper Size and... -
Page 6: Printing A Document
Open the front door by pressing the button on the left side of the printer and lowering the front door. Pull the photoconductor kit and toner cartridge out of the printer as a unit by pulling on the toner cartridge handle. Note: The photoconductor kit and toner cartridge form a unit. -
Page 7: Replacing The Toner Cartridge
Install the unit into the printer by aligning the arrows on the guides of the unit with the arrows in the printer. Push the unit as far as it will go. After you replace the photoconductor kit, reset the photoconductor counter. -
Page 8: Cleaning The Exterior Of The Printer
Wipe only the outside of the printer. Warning—Potential Damage: Using a damp cloth to clean the interior may cause damage to your printer. Make sure all areas of the printer are dry before beginning a new print job.