Related Manuals for Omega OS 531
Summary of Contents for Omega OS 531
- Page 1 Installation and operating manual OS 531 Ultrasonic Leak Detector Document : 3403235 Language : Eng Rev. : 002 Date : 7.4.2021...
- Page 2 The device is designed exclusively for the described application. Omega air d.o.o offers no guarantee for the suitability for any other purpose. Omega air d.o.o. is also not liable for consequential damage resulting from the delivery, capability or use of this device.
-
Page 3: Table Of Contents
Performing initial setup ........................... 11 Procedures of conducting a leak survey ........................13 Using the OS 531 in the non-LMS mode ......................13 Using the OS 531 in the LMS mode ....................... 14 Setting up and Starting a leak survey ........................15 Switching the OS 531 to the required mode .................... - Page 4 16.2 Headset operations ............................31 16.3 Working as a wireless headset........................31 16.4 Working as a wired headset ........................31 16.5 Pairing a new headset with the OS 531 ....................... 32 16.6 Care and maintenance ..........................32...
-
Page 5: Safety Instructions
Safety instructions Please check if this instruction manual matches the product type. Please observe all notes and instructions indicated in this manual. It contains essential information which must be observed before and during installation, operation and maintenance. Therefore this instruction manual must be read carefully by the technician as well as by the responsible user or qualified personnel. -
Page 6: Application
Software), which is specifically designed for the OS 531. LMS is purchased independent of OS 531, and can be installed on a local or cloud-based server. The OS 531 can work in the LMS or Non-LMS mode. This manual takes you through how to use OS 531 in these two modes. -
Page 7: Electrical Data
Pressure / diameter 0.1 mm 0.2 mm 0.5 mm 0.5 bar 0.5 m 1.7 m 5.0 bar 3.6 m 11.5 m 18 m Scope of delivery The OS 531 layout in the transportation case is shown as below. -
Page 8: Learning About The Device
Battery charger Type-C USB stick Transport case Leak tags to mark found leaks, 100 pieces Instruction manual Calibration certificate Ultrasonic tone generator Calibration for OS 531 Learning about the device This chapter describes components of the OS 531 main unit. -
Page 9: Components
6.1 Components Part Function Power button: Long press to turn OS 531 on or off. It also works as a shortcut button for taking photos in leak detection. Voice recording button: Press to record voice memos in leak detection. Laser button: Press to turn laser on or off. - Page 10 Sensitivity Setting Shows the sensitivity level. You can adjust the setting by turning the sensitivity wheel. Indicates the intensity of the sound that the OS 531 detects： Red strongest, yellow the less, and green the least. You can see the actual sound level in DB in the Sound Level area.
-
Page 11: Dimension And Electrical Ports
Before you start for the first time Before you use a new OS 531 to detect leaks for the first time, charge the device and perform the initial device setup. 7.1 Charging the device OS 531 is a battery-powered device and partially charged before delivery. - Page 12 Note: The headset is paired with the OS 531 before delivery. The OS 531 can work with only the wireless headset supplied by Omega air. After you purchase a new headset from Omega air, you must pair it with your OS 531 on your own.
-
Page 13: Procedures Of Conducting A Leak Survey
Procedures of conducting a leak survey A leak detection project is managed by a “survey”. An OS 531 can work in non-LMS mode or LMS mode. The procedures between these two modes lie in: In the non-LMS mode, surveys are created in the OS 531. -
Page 14: Using The Os 531 In The Lms Mode
Steps: 8.2 Using the OS 531 in the LMS mode Steps performed on the OS 531:... -
Page 15: Setting Up And Starting A Leak Survey
In the LMS+OS 531 application scenario, there are three user roles who assume different job responsibilities. See the below table for their description. Only users in the technician role are allowed to access the OS 531 and use it to detect leaks. Role... -
Page 16: Switching The Os 531 To The Required Mode
To the non-LMS mode, switch off this toggle. 9.2 (Non-LMS mode only) Creating a survey When the OS 531 in the non-LMS mode, to conduct a leak survey for a site, you must first create the survey in the OS 531. -
Page 17: Downloading The Survey Information From The Lms
An OS 531 can work for only one survey at a time. If you download the information of a survey to the OS 531, only the leak records detected under this survey can be viewed and managed on the OS 531 screen. Leak records of the previous survey can be accessed only through a PC that is connected to the OS 531 (See section 13.2... -
Page 18: Specifying The Survey Settings
Note: In the non-LMS mode, after the survey is started, you can change the units of flow and pressure, but cannot change the currency unit. 5. If the OS 531 is in the LMS mode, click Record Option Settings, and switch on or off the toggles as needed to... -
Page 19: Starting The Survey
Note: In the LMS mode, the flow and pressure units and cost-related settings are configured by an officer in the LMS. When you download a survey to the OS 531, these settings are downloaded to the OS 531 along with other survey data. - Page 20 • You can adjust the sensitivity by turning the • sensitivity wheel on the OS 531 handle. 2. To turn on the laser, press the Laser push button as shown on the left-hand side. Note: To avoid laser injury, the the laser function is enabled only when the home screen is displayed.
-
Page 21: Recording Leaks
To get accurate results, we recommend you record leaks at a fixed distance of not more than 1 m and with the trumpet mounted on the OS 531. You can detect leaks from a distance, but keep in mind that recording loss estimation is best performed at a close distance. - Page 22 Two voice memos are allowed for a leak, and each can last up to 1 minute. 12. Depending on the working mode that your OS 531 is working in, your actions are different: • If your OS 531 is working in the non-LMS mode, skip to steps 13.
- Page 23 Note: The recording items in the chart can be hidden from the process using the menu of Survey Settings > Record Option Settings. For any hidden record items or record items that you skipped by clicking the Skip button, the OS 531 will save their default values to the leak record.
-
Page 24: Managing Leak Records
12.1 Viewing and editing a leak record You can view a leak record in the OS 531, and edit the leak details if needed. If you are not satisfied with the leakage data, you can delete the leak record and record again. -
Page 25: Copying Leak Records To A Pc
3. On the PC, double click My Computer. Note: On the PC, the OS 531 is identified as a USB drive. When the OS 531 is connected to a PC for the first time, the OS 531 driver will be automatically installed on the PC. -
Page 26: Uploading The Leak Records To The Lms
7. Copy the desired survey folders to the local. 12.3 Uploading the leak records to the LMS If you are using the OS 531 in the LMS mode, after you partially or fully complete the leak detection, you can upload the detected leak records to the LMS. - Page 27 ◦ The OS 531 user settings are reset to the factory defaults. ◦ The leak data except the photo, voice recording and CSV files will be deleted from the OS 531. To avoid losing the leak data, before the update, please upload the leak data to the LMS. If you need the leak data in the CSV format, make sure that you generate the CSV file before uploading the leak data to LMS.
- Page 28 Preparation: Copy the new firmware to the root directory of the Type-C USB stick included in the delivery package. Steps: 1. Access Menu > Device Information to view the current firmware version. 2. Access Menu > Device Setting > Firmware Update. 3.
-
Page 29: Resetting The Device
6. Insert the prepared USB stick to the OS 531. 7. On the screen that appears, you can see the files in the root directory of the USB stick. Navigate to the desired firmware file and single click to select. -
Page 30: Disposal Or Waste
To detect leaks at a tank, place an ultrasonic tone generator inside the tank, the ultrasonic that is produced by the generator can flow through leaks and be detected by OS 531. Disposal or waste Electronic devices are recyclable material and do not belong in the household waste. -
Page 31: Appendix A: Headset Overview
B. Switch on the Wireless Headset toggle. After successfully connected, the message “EDIFIER W860NB connected” appears on the OS 531 screen. Note: For the purpose of automatic wireless connection, please do not press and hold the power button in the headset for more than 3 seconds. - Page 32 16.5 Pairing a new headset with the OS 531 If you purchase a new headset, you must pair the new headset with your OS 531. Detailed steps are as follows. 1. Press and hold the power button for 5 seconds to enter the pairing mode.
- Page 33 OMEGA AIR d.o.o. Ljubljana Cesta Dolomitskega odreda 10 SI-1000 Ljubljana, Slovenia Tel.: +386 (0)1 200 68 00 Fax.: +386 (0)1 200 68 50 E-mail: info@omega-air.si www.omega-air.si...