Summary of Contents for NCR OPTIC Ovation 2 Printer Reuse Kit
- Page 1 Installation Instructions NCR OPTIC Ovation 2 Printer Reuse Kit Kit Number: 6002-K007-V001 (497-0515156) 497-0517177 Issue A...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
- Page 3 Preface Audience This book is written for end users (System Administrator and Maintenance Technician), NCR Field Engineering, and VAR/OEM Hardware and System Integrators Notice: This document is NCR proprietary information and is not to be disclosed or reproduced without consent.
- Page 4 Safety and Compliance Information This section introduces the hazards and safety precautions associated with installing, inspecting, maintaining or servicing the Printer Reuse Kit. Before proceeding, check the relevant hazard and safety information. Fire, explosion or electrical shock could occur and cause death or serious injury if these safe service procedures are not followed. All work must be carried out in accordance with NFPA (National Fire Protection Association) 30, 30A, and 70, and any local authority.
- Page 5 Read, understand and follow this manual and any other labels or related materials supplied with the equipment. If you do not understand a procedure, call NCR. It is imperative to your safety and the safety of others to understand the procedures before beginning work.
- Page 6 Safety Symbols and Terminology Caution: This safety alert symbol is used in this manual and on warning labels to alert you to a precaution which must be followed to prevent potential personal safety hazard. Obey safety directives that follow this symbol to avoid possible injury or death. Signal Words Warning: Alerts you to a hazard or unsafe practice which will result in death or...
- Page 7 If you do not have access to a computer, you may leave a voice message at: 1-800-528- 8658 (USA), or (International) +1-770-623-7400. When leaving a message, please provide a phone number and/or an email address so NCR can contact you if additional details are needed.
- Page 8 viii Warranty Warranty terms vary by region and country. All parts of this product that are subject to normal wear and tear are not included in the warranty. In general, damages due to the following are not covered by the warranty. •...
- Page 9 • Description of the problem, including any system error codes, error condition, or guidance to the area of failure. The NCR Agent will provide you with a work order number, which serves as your Return Material Authorization (RMA). Please provide the RMA on the outside of the shipping box.
- Page 11 Revision Record Issue Date Remarks March First Issue 2017...
-
Page 13: Table Of Contents
xiii Table of Contents Ovation Printer Reuse Kit Contents Kit Contents Printer Deinstallation Printer Installation Install the Printer Door (497-0515157) Install the Printer to the Dispenser Door... -
Page 15: Ovation Printer Reuse Kit Contents
Ovation Printer Reuse Kit Contents Ovation Printer Reuse Kit Contents Note: 2 kits are needed per 2 sided dispenser. Caution: This Printer Reuse Kit must be installed in combination with the Ovation OPTIC 12 Retrofit Kit, Listed by Report Retrofit Kit Part Number 6002-0006-8801. Kit Contents Part Number Description... -
Page 17: Printer Deinstallation
Printer Reuse Kit Printer Deinstallation 1. Unlock the Printer door with the Ovation Printer Key and pull out the printer. 2. Unplug the printer from the interior components and DC power board. Note: Disconnecting of the USB/Comm cable should have been done during the deinstallation section of the Retrofit Kit Instructions. - Page 18 Printer Reuse Kit Note: The DC power board is located on Side A of the dispenser. 3. Unscrew the Ground Wire from the slide cover.
- Page 19 Printer Reuse Kit 4. Pull out the Printer Door by disengaging the slide latch on the bottom of the printer. 5. Remove the printer from the Slide. a. Unscrew the two side screws using a 3mm Hex Key and retain.
- Page 20 Printer Reuse Kit...
- Page 21 Printer Reuse Kit b. Slide the printer back and up off the securing bottom stud and retain. Remove and retain the bottom stud. Continue the Dispenser Retrofit Deinstallation Process. Follow the OPTIC 12 Ovation 2 Retrofit Kit installation instructions (497-0517176), UL Listed by Report Retrofit kit part number 6002-0006-8801.
-
Page 22: Printer Installation
Printer Reuse Kit Printer Installation Install the Printer Door (497-0515157) 1. Remove the adhesive cover from the door hinge as shown. 2. Attach the hinge to the right side of the door and secure with the 4 provided nuts (006-8611952) on the back side of the dispenser door. -
Page 23: Install The Printer To The Dispenser Door
Printer Reuse Kit 3. Install the gasket (497-0514265) over the side of the hinge making sure the gasket stays within the channel in the dispenser door. Orient the gasket so the thick side of the gasket covers the hinge. Continue the Dispenser Retrofit Installation. Follow the OPTIC 12 Ovation 2 Retrofit Kit installation instructions (497-0517176), UL Listed by Report Retrofit kit part number 6002-0006-8801. - Page 24 Printer Reuse Kit b. Place the retained printer onto the Reuse Chassis. Route the cables through the mailbox towards the back of the chassis. Fit onto the bottom stud.
- Page 25 Printer Reuse Kit...
- Page 26 Printer Reuse Kit c. Slide the printer forward on the Reuse Chassis until the front of the printer mates up to the gasket shown and engages the Chassis snap. d. Install the 2 retained screws to the Reuse Chassis to secure the printer.
- Page 27 Printer Reuse Kit 2. Adjust the bottom printer support rod to the correct height with a 10mm wrench or monkey wrench. a. Place the Nut (006-8611858) onto the Support Rod (006-8625421).
- Page 28 Printer Reuse Kit b. Install the support rod to the bottom of the printer chassis. c. Adjust the support rod so the Reuse Printer Assembly can be installed. The support rod should be able to just clear the bottom edge of the dispenser door. Adjust the rod by turning the nut towards the bottom of the support rod and then tightening the rod deeper into the printer chassis.
- Page 29 Printer Reuse Kit 3. Install the Printer to the dispenser door. a. Install the 4 printer chassis support screws (006-0654018) to the dispenser door as shown. Note: Printer door should be open to make install easier. b. Slide the printer assembly onto the support screws.
- Page 30 Printer Reuse Kit c. Tighten the 4 support screws.
- Page 31 Printer Reuse Kit d. Make final support rod adjustments. The support rod should be adjusted so it sits on the bottom edge of the dispenser door. Loosen the rod from the printer chassis until it touches the bottom of the door and meets slight resistance. To keep the rod in place, tighten the nut against the bottom of the printer chassis.
- Page 32 Printer Reuse Kit 4. Plug in the printer USB cable to the OPTIC 12 Printer USB Port. 5. Route and plug in the Printer Power cable to the DC power board inside the dispenser.
- Page 33 Printer Reuse Kit...
- Page 34 Printer Reuse Kit 6. Install the grounding cable (497-0513687) to the Printer cover by removing the top left printer cover screw (when looking at the back of the dispenser door), sliding on the grounding cable, and reattaching the cover screw as shown below. 7.
- Page 35 Printer Reuse Kit 8. Verify the wires have been routed correctly by fully extending the printer slide through the printer door and pushing it back in and checking the wire clearance. Caution: If wires come in contact with the paper area at any point this could cause a printer malfunction.