Time Keeping Mode - Setting The Upv For The Timer And The Timer Counting Display; Time Keeping Mode - Using The Timer; Altimeter Mode And Its Sub-Displays - La Crosse Technology K2-100 User Manual

4.8 Time Keeping Mode
- Setting the UPV for the Timer and the Timer Counting Display
hold
adjust
mode
button
digits have been
selected (flashing)
Timer Display User Pre-set Value (UPV)
Setting Display
hold
adjust adjust
adjust
hour minute second
Timer Counting Display
mode
adjust (Countdown Timer or adjust
button
Repeater Timer)
UPV and Timer Counting Display Setting Sequence
4.9 Time Keeping Mode
- Using the Timer
digits start
counting
start/stop
Counting Display
Timer Display
(Timer sets as 1 minute)
start/stop
digits stop
counting
hold
lap/reset
Stop Counting Display
start/stop
digits start
counting
again
Counting Display
To Set the UPV and the Timer Counting DIsplay
- Press and hold the [adjust] button for 2 seconds to
change the display from Timer Display to User Pre-set
Value Setting Display .
- T h e h o u r d i g i t s f l a s h o n t h e d i s p l a y b e c a u s e i t i s
being selected.
The setting procedure
- Press [adjust] button to change the selection as in the
User Pre-set Value Setting Sequence.
- While digits are being selected (flashing), press
[start/stop] button to increase the number; press the
[lap/reset] button to decrease the number. Hold down the
button to change the number at a higher speed.
- W h e n t h e F L A S H I N G P A R T m o v e s t o " R E P E A T " o r
"COUNT " character, just press [start/stop] or [lap/
resst] button to select the Countdown timer or Repeater
timer.
- After you set the timer, press the [mode] button to exit
the setting sequence.
- If no bu tton is pressed in the setting display for about 3
m i n u t e s , t h e K 2 - 1 0 0 w i l l r e t u r n t o t h e T i m e r M o d e
automatically
12
13
To Use the Timer
- When the Timer is set, press the [start/stop] button to
start the timer. Press the [start/stop] button again to stop
the timer.
- The time to 'Zero' will be shown on the display.
- The timer starts to beep every second when it is 5
seconds from the end of the countdown.
- When the countdown time is reached, a long beep that
lasts for 2 seconds will be heard.
- Pressing any button in this period will terminate the beep
sound prematurely.
- The user preset time will be loaded automatically at the
end of the beep sound.
To Reset the Timer
- Press and hold the [lap/reset] button for 2 seconds to
reset the timer after it has stopped.
13
14

5.0 Altimeter Mode and its sub-displays

adjust
button
the
Altitude Setting Sequence
(from -24 hour to -15 min.
by backward scrolling
(from -15 min. to -24 hour)
5.0 Altimeter Mode and its sub-displays ...
60
m
P
30
Altimeter Graph Display
adjust
button
adjust
adjust
button
mode
button
adjust
button
adjust
mode
button adjust
button
button
To view the memory
start/stop
by forward scrolling
lap/reset
To view the memory
24 Hour Memory Display
14
15
lap/reset
button
Graph Scale Display
hold
lap/reset
C (Celsius)
m (Meter)
hold
lap/reset
F (Fahrenheit)
m (Meter)
Unit Selection Sequence
15
16
hold
60
m
P
30
Altimeter Graph Display
continue
hold
lap/reset
C (Celsius)
ft (Feet)
hold
hold
lap/reset
lap/reset
F(Fahrenheit)
ft (Feet)