Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Wilson Benesch FIBONACCI Series
Summary of Contents for Wilson Benesch FIBONACCI Series
- Page 1 FIBONACCI SERIES User Manual...
- Page 2 Wilson Benesch Loudspeaker at the heart of the system. Before starting your journey, we encourage you to pay special attention to the information contained in this manual. All Fibonacci Series products have been designed and built with precision.
-
Page 3: Table Of Contents
Table of Contents 1.0 Product Registration __ P4 4.0 Stable Listening Room Environment & Surface Finishes - P12 1.1 Unpacking: Important points before setup __ P4 4.1 Running-in (168-Hours) __ P12 1.2 What is in the Box __ P5 4.3 Partnering Products __ P13 4.4 Handwheel and Extension Plate Removal __ P13 2.0 The Subject of Room Acoustics __ P6 4.5 Other Adjustments __ P13... -
Page 4: Product Registration
During installation please observe normal procedures for lifting and correct posture when handling the speakers. It is strongly recommend for the smaller products that two people work together to unpack the product. With the largest products in the Fibonacci Series at least three people will need to work together to unpack the product and safely install it. -
Page 5: What Is In The Box
• • • 2x Product Grille(s) • • • • • • 2x Loudspeaker Covers • • • • • • 2x Port Bungs • 2x Terminal Link Leads • • • • • • FIBONACCI SERIES MANUAL REV 1.0... -
Page 6: The Subject Of Room Acoustics
We strongly recommend that customers have your Wilson Benesch dealer do the final voicing and positioning of your Wilson Benesch loudspeaker with you. -
Page 7: Reflection, Absorption, Diffusion
It is the goal that is the guide and the owner is the pivot in this subtle balancing act. FIBONACCI SERIES MANUAL REV 1.0... -
Page 8: Loudspeaker And Listening Position
-Select one passage with a full orchestra like The Pines of Rome. -Select one that is very emotional for you. -Select one that has a strong rhythm and a good portion of bass content, as found in a typical dance music track for example. FIBONACCI SERIES MANUAL REV 1.0... -
Page 9: Speaker Toe-In
2.8 Kinematic Location Cups or Spikes In listening rooms with a carpet Wilson Benesch recommend using spiked termination, where the objective is to drive through the carpet and into the sub-floor to achieve maximum stability for the speaker. For hard floors or low-pile carpets use of Kinematic Location Cups is recommended. -
Page 10: Bi-Amping
3.2 Terminals Wilson Benesch recommends the use of 8mm ring or spade connector cable terminations. A spanner is provided to tighten up the rhodium plated nuts. A light pinch of the end of the supplied spanner is more than sufficient to tighten the nuts. Please be careful to not over tighten the terminals as this could result in damage to the terminal plate or snapping of the terminal. -
Page 11: Loudspeaker Terminal Wiring
3.3 Loudspeaker Terminal Wiring Wilson Benesch Fibonacci Series loudspeakers have two pairs of terminal lozenges that are positioned at the rear of the foot of the speaker and are supplied with link wires for linking the terminals for single wired or bi-wired operation. Figure 1. Shows the terminal on the Fibonacci Series. -
Page 12: Stable Listening Room Environment & Surface Finishes - P12
During periods when the loudspeakers will not be used, it is recommended that they are covered. In areas of the world where high humidity, and or, air pollution is prevalent such as in large city areas, Wilson Benesch highly recommend the use of air purifiers and air conditioning to maintain a steady state, stable environment for your loudspeakers and electronics. -
Page 13: Partnering Products
4.3 Partnering Products There are a huge number of products available throughout the world that can be partnered with Wilson Benesch loudspeakers and it would not be helpful to the end user to make any specific recommendations for any particular cabling or electronics products that are “guaranteed” to meet or exceed all of the expectations for the end user. -
Page 14: Limited Warranty
Most repairs can be made in the field. In instances where return to Wilson Benesch’s factory is required, the dealer or customer must first obtain a return authorisation. The purchaser must pay for shipping to Wilson Benesch. In the event that the product defect is deemed to be due to a manufacturing defect or failure of the component covered under the Limited Warranty, Wilson Benesch will pay for shipping of its choice to return the product to purchaser. -
Page 15: Remedy
Warranty shall be to: (1) contact an authorised Wilson Benesch Dealer within the Warranty Period for service or repair of the product without charge for parts or labour. The service or repair shall take place either at the location where the product is installed or at the Dealer’s place of business, at the dealers option. or, (2) if purchaser has sought timely service or repair and the product cannot be serviced or repaired by the dealer, then the purchaser may obtain a return authorisation from Wilson Benesch and at purchaser’s expense return the product to Wilson Benesch where the defect will be rectified without charge for parts or labour. - Page 16 Wilson Benesch Ltd. Falcon House Limestone Cottage Lane Sheffield S6 1NJ T: +44 (0)1142 852656 E: info@wilson-benesch.com W: www.wilson-benesch.com...