Download Print this page

NANOLUX LEDex F630 Operating Manual

Led top lighting 630w

Advertisement

Quick Links

ALWAYS COMPLY WITH LOCAL
INSTALLATION REGULATIONS AND CODES
The fixture is suitable for both indoor and greenhouse environment. Do not install your
LED in wet environment. Do not operate the fixture close to combustible materials.
The fixture will get hot during operation. Do not touch the fixture during or right after
operation. Make sure the power cord does not touch any hot part of the fixture. Make
sure the light bar is clean and inserted correctly. The normal operating environment
temperature should be below 104°F. Exceeding the maximum environmental
temperature will stress electronic components, which will lead to shorter lifetime and
decreased reliability.
Our fixture comes with a heat sink and other cooling components, which enable it to
dissipate heat effectively and allow maximum heat conductivity during the operation.
SCOPE OF USE AND MAINTENANCE
● Comply with local installation regulations.
● Store the fixture in a dry and clean environment, with an ambient temperature of
-10°C ~ 50°C and ambient humidity of less than 90% RH. It is recommended that
the fixture shall not stay unused for more than six months. If it has stayed unused
for more than six months, please test to ensure fixture is functioning at 100%.
● Please keep products safe. Avoid mechanical pressure, excessive vibration and
dropping the unit during the process of assembly to protect the light bar.
● Keep away from water, oil and organic solvent, or it will reduce the efficacy and have
the potential risk of electric leakage.
● All equipment, devices and machines shall be effectively grounded.
● Regularly check and clean the dust from the heatsink and LED array.
1. Disconnect from power supply before general care.
2. Remove the dust from the light bar by using low-pressure compressed air.
3. Clean the diode array with a soft cloth to prevent it from being scratched.
4. Be sure not to touch the diode with your bare hands, even after the LED is
disconnected from power supply.
● It is recommended that you contact a licensed electrician or an expert if any of the
following happens:
1. The cable or the plug has been damaged.
2. The unit has been exposed to rain.
3. Significant changes in the unit performance.
4. Fixture or light bar dropped and corner of its enclosure got bent.
● There are no serviceable parts inside the LED. Opening the LED will void its
warranty.
TROUBLE SHOOTING
Problem
Probable cause(s)
One or more
fixtures are
Disconnect from power source.
completely off.
Broken cable or wire connecting
Dimming
controller to fixture or wire
failure
connecting fixture to fixture.
The power supply settings do
LED will not
not match with local AC
come on.
voltage and frequency.
WARRANTY
Nanolux warrants manufacturing defects of this product if it is used under normal
operating conditions for a period of three (3) years from the original date of purchase.
If the product shows manufacturing defects within this period and that defect is not
caused by user error or improper use, Nanolux shall, at its discretion, either replace or
repair the product by using applicable new or refurbished parts. For any service, return
the product to your shop along with the original sales receipt.
PATENTED PRODUCTS, COUNTERFEITING NOT ALLOWED.
Designed by NANOLUX in California
Made in China
Possible fixes or
corrective maintenance
Make sure power is on and
cables are plugged in.
Repair or replace any
damaged cables if necessary.
Disconnect fixture from the
power supply. Check settings
and correct if necessary.
OPERATING
MANUAL
LED
Modular design
LED TOP LIGHTING 630W
0-10V SLC COMPATIBLE

Advertisement

loading

Summary of Contents for NANOLUX LEDex F630

  • Page 1 If the product shows manufacturing defects within this period and that defect is not caused by user error or improper use, Nanolux shall, at its discretion, either replace or repair the product by using applicable new or refurbished parts. For any service, return the product to your shop along with the original sales receipt.
  • Page 2 Light Bar Output Plug TECHNICAL SPECIFICATIONS 0-10V DIMMING Model LEDex F630 This model is compatible with SLC controller. Connect the signal wire plug on the LED driver to the 1 end of the Y shape signal wire, AC120V/208V/240V/277V Input Voltage...