Sealey PC200A Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMP P OR R TA TANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
TH H E P P RO O DUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PE E RS S ON N AL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Keep in dry area
instructions protect from rain
1. SAFETY
1.1. ELECTRICAL SAFETY
 WARNING! It is the user's responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with
all electrical products. You may obtain an RCD by contacting your local Sealey Stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fi tted with the
correct fuse - see fuse rating in these instructions.
 DO NOT pull or carry the appliance by the power cable.
 DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a fi rm grip on the plug.
 DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or replaced immediately by a
qualifi ed electrician.
1.1.4. This product is fi tted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualifi ed electrician.
Class II products are wired with live (brown) and neutral (blue) only, and are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
 DO NOT connect either wire to the earth terminal.
Sealey recommend that repairs are carried out by a qualifi ed electrician.
1.2. GENERAL SAFETY
 WARNING! This ash vacuum cleaner is for the vacuuming of cold ashes from fi replaces, wood or coal stoves, BBQ's and grills.
NOTE: Cold ash is defined as ash that has sufficiently cooled down without any pockets of hot embers.
 Rake through the ash with metal tools, to check for any hot embers prior to using the ash vacuum cleaner.
 DO NOT use for vacuuming materials with a temperature above 40ºC.
▲ DANGER! DO NOT vacuum hot or glowing ash, cigarette ends, infl ammable, explosive, corrosive or other dangerous substances.
 DO NOT use to vacuum soot.
 DO NOT use to vacuum the following health hazardous dusts:
Class L (soft woods and solid surface material).
Class M (hard woods, board materials, concrete and brick dust).
Class H (asbestos and mould).
DO NOT operate the ash vacuum cleaner without the fi lter in place. Using the ash vacuum cleaner without the fi lter may result in

motor failure and will invalidate the warranty.
 DO NOT allow children or untrained persons to operate the ash vacuum cleaner.
 DO NOT place the attachments close to your face.
 DO NOT point the hose end at other persons or animals.
 DO NOT leave the ash vacuum cleaner running unattended. Turn the power supply OFF when not in use.
 DO NOT operate the ash vacuum cleaner while under the infl uence of drugs, alcohol or intoxicating medication.
 DO NOT use the ash vacuum cleaner in the rain or in very damp conditions.
 DO NOT use the ash vacuum cleaner for a task it is not designed to perform.
 Disconnect the ash vacuum cleaner from the power supply before servicing, changing accessories, or performing and
maintenance.
Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty.

© Jack Sealey Limited
20L 3-IN-1 ASH VACUUM CLEANER
1200W/230V
PC200A
MODEL NO:
Original Language Version
Recommended fuse rating
13 Amp
PC200A Issue 1 23/11/21