Pelonis HF-0063 Digital Fan Heater Manual

PLEASE READ AND SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater or return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
9. To disconnect heater, first turn controls to off, then remove plug from outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use it in the areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
14. 
    Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
15. This heater draws 12.5 amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
16. It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.
17. The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
18. 
    To prevent electric shock, match wide blade of plug to wide slot and fully inser.
19. "SAVE THESE INSTRUCTIONS"

ASSEMBLY

This heater is pre-assembled in factory.

ELECTRICAL RATINGS

This product is rated 12.5 amps (1500W) at 120V, 60 Hz.

FEATURES

OPERATING INSTRUCTIONS

Your heater is equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your outlet. DO NOT defeat the safety purpose of the polarized plug.

• Place the heater on a firm level surface free from obstructions, and at least 3 ft. away from any wall and any other objects such as furniture, curtains, plants or combustible material.
• Plug the heater into a grounded 120V outlet. The buzzer sounds, after pressing the power button, the Digital Screen indicates current temperature.
• Press the Power button repeatedly to the desired setting. The cycle is as follows:
• High: Heater operates at a higher wattage, around 1500 Watts.
• Low: Heater operates at a lower wattage, around 900 Watts.
• Fan: The fan circulates room air only. The heating elements are "OFF"

Turning the Unit Off

• Press the POWER button to cycle through the functions until none of them are lit (High, Low, Fan).

After the unit is turned off, the fan will continue to run for 15 seconds to cool down, the digital screen will display the process from 15 backward to 1. After the display turns off, unplug the heater from the electrical outlet.

Set the desired temperature

• In order to set the thermostat the unit has to be on High or Low.
• When the unit is on, press the ▲ or ▼ button, the buzzer sounds and the setting temperature flash on the digital screen.
• At this time you can press the ▲ or ▼ key to the temperature desired. (40F-95F).
• Wait for around 5 seconds until the digital screen displays the current temperature again.

Note: If the current temperature is higher than the set temperature (95F is original set temperature), the unit will stop heating.

Setting timer

Setting the heater to turn off automatically

• In order to set the unit to turn off, the unit must be on (High or Low).
• Press the Timer button, the timer setting pilot will illuminate.
• You can see "0" flashes on the digital screen.
• Press UP or DOWN button repeatedly to set the auto-off time within 12 hours.

The timer indicator will appear on the digital screen after the timer is set. You can check the remaining time of timer by pressing the TIMER button.

Setting the heater to turn on automatically

• In order to set the unit to turn on, the unit must be off.
• Press the Timer button, the timer setting pilot will illuminate, and you can see "0" flashes on the digital screen.
• Press UP or DOWN button repeatedly to set the auto-on time within 12 hours.

Cancelling the timer setting
When the timer indicator is lit, pressing the POWER button will cancel the timer setting.

Oscillation function

In order to set the heater to oscillate, the heater must be on (High, Low or Fan). Press the OSC button once to activate the oscillating function and press the OSC button one more time to disable oscillating function.

RESET INSTRUCTIONS

• This heater is equipped with an internal High Limit Switch which causes the unit to stop operating in the event the internal temperature exceeds normal operating temperatures.

IF THE UNIT SHUTS DOWN

1. TURN THE UNIT OFF
2. UNPLUG UNIT WAIT COOLING DOWN
3. PLUG IN AND TURN ON

IF YOUR HEATER FAILS TO OPERATE

• Be sure it is plugged in and that the electrical outlet is working.
• Check for any obstruction. If you find an obstruction turn the heater OFF. Unplug the heater and wait at least ten minutes for it to cool. Carefully remove the obstruction. Plug the heater back in and restart it as described under OPERATION.
• If you still notice the same defect above mentioned, remove the plug from the socket and have the appliance serviced by authorized service personnel only.
• Check that the setting temperature is not set lower than the current room temperature. Set the desired temperature higher than the current temperature to restart the heater.

TROUBLESHOOTING

If your heater fails to operate, please follow these instructions:

• Ensure that your circuit breaker or fuse is working properly.
• Be sure the heater is plugged in and that the electrical outlet is working properly.
• Check for any obstruction. If you find any obstruction, turn the heater off. Unplug the heater and wait a few minutes for it to cool down. Carefully remove the obstruction. Plug the heater in and turn it on again by referring to the OPERATING INSTRUCTIONS.

NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEE THE WARRANTY INFORMATION FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CONTACT US BY REFERRING TO THE SERVICE & SUPPORT INFORMATION.

CLEANING AND STORAGE

We recommend that the heater be cleaned at least once a month and before off-season storage.

• Turn the heater OFF and unplug it. Allow it to cool.
• Use a dry cloth to clean the external surfaces of the heater.
  DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION.
• Clean your heater using the above-mentioned steps, then pack the heater in its original container and store it in a cool dry place.
• This heater does not disassemble.
• The motor is factory lubricated for life, and will require no further lubrication.

SPECIFICATIONS

SERVICE & SUPPORT

In the event of a warranty claim or if service is required for this heater, please contact us at the following:

Tel: 866 646 4332
Email us at: customerservice@supportuscenter.com

For questions or comments, please write to:
Midea America Corporation
Customer Care Center

11411 NW 107th Street, Suite 12
Miami, FL 33178

For your records, staple your sales receipt to this manual and record the following:
DATE OF PURCHASE
PLACE OF PURCHASE

NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS

ONE (1) YEAR LIMITED WARRANTY

• Please read all instructions before attempting to use this product.
• Please return the Warranty Registration card within fifteen (15) days from the date of purchasing this product.

PELONIS warrants as limited herein to the original purchaser of retail that each new Pelonis Digital Fan Heater, shall be free of defects in material and workmanship for a period of one (1) year from the date of original purchase. This one (1) year warranty is limited to the heating elements, motor, and electric control circuit board.

In the event of malfunctions or failure of your Pelonis Digital Fan Heater, simply deliver or send the heater, postage prepaid along with PROOF OF PURCHASE, within the warranty period of one (1) year, to PELONIS. PELONIS reserves the right to inspect the claimed defective part or parts to determine if the defect or malfunction complaint is covered by this warranty. PELONIS shall, within sixty (60) days after receipt of the product, at its option, repair and/or replace the defective part or parts free of charge. This warranty shall only cover defects arising from normal usage. PELONIS assumes no responsibility whatsoever if the Fan Forced heater should fail during the warranty period by reason of:

• Misuse, negligence, physical damage or accidents.
• Lack of maintenance (see instructions for proper maintenance).
• Repair by any unauthorized party during the warranty period.
• Damage caused by connection to an improper input voltage (see specification label on your heater).

PELONIS makes no further warranties or representations, express or implied except those contained herein. No representative or dealer is authorized to assume any other liability regarding the Fan Forced heater. The duration of the implied warranty granted under State law, including warranties of merchantability and fitness for particular purpose are limited in duration should the duration of the express warranty grant it hereunder. PELONIS shall in no event be liable for direct, indirect, special or consequential damages.

Some states do not allow limitations on how long an implied warranty lasts, and/or the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights and you may have other rights which vary from state to state.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Pelonis HF-0063 Digital Fan Heater Manual