Black Box EME1D1-005-R2 User Manual

Black Box EME1D1-005-R2 User Manual

Isolated digital viltmeter

Advertisement

Quick Links

USER MANUAL
SETUP GUIDE
RS-TOUCH SERIES
EME1D1-005-R2
IN-SESSION
ISOLATED DIGITAL
COMMON
VOLTMETER
SETTINGS
24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM
24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM

Advertisement

Table of Contents
loading

Summary of Contents for Black Box EME1D1-005-R2

  • Page 1 USER MANUAL SETUP GUIDE RS-TOUCH SERIES EME1D1-005-R2 IN-SESSION ISOLATED DIGITAL COMMON VOLTMETER SETTINGS 24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM 24/7 TECHNICAL SUPPORT AT 1.877.877.2269 OR VISIT BLACKBOX.COM...
  • Page 2: Chapter 1: Introduction

    1.1 INTRODUCTION The EME1D1-005-R2 is an isolated digital DC volt meter which can be used to monitor and log DC voltage readings from batteries and other equipment. It can also be used to integrate third-party sensors that have DC voltage output.
  • Page 3: Chapter 2: Specifications

    NEED HELP? LEAVE THE TECH TO US LIVE 24/7 CHAPTER 2: SPECIFICATIONS TECHNICAL SUPPORT 1.877.877.2269 2.1 SPECIFICATIONS TABLE 2-1. GENERAL SPECIFICATIONS SPECIFICATION DESCRIPTION Measurement Range 0 to +60V or -60 to 0VDC Isolated ground for protection against a differential ground between the target device and the Ground sensor Range...
  • Page 4: Chapter 3: Product Use

    NEED HELP? LEAVE THE TECH TO US LIVE 24/7 TECHNICAL CHAPTER 3: PRODUCT USE SUPPORT 1.877.877.2269 3.1 SENSOR LEDs TABLE 3-1. SENSOR LEDs DESCRIPTION Host Connection LED LED will be GREEN when connected successfully to your base unit. Status LED LED will be blinking YELLOW when in an alert state.
  • Page 5 NEED HELP? LEAVE THE TECH TO US LIVE 24/7 CHAPTER 3: PRODUCT USE TECHNICAL SUPPORT 1.877.877.2269 3.5 USING THE ISOLATED DIGITAL VOLTMETER TO INTEGRATE CUSTOM SENSORS The unit has the ability to integrate with custom sensors via our Isolated Digital Voltmeter or 4-20mA Converter. For integration with custom sensors, the unit text can be customized to meet your needs;...
  • Page 6 3.6 CALIBRATING THE ISOLATED DIGITAL VOLTMETER The calibration of the EME1D1-005-R2 sensor can only be performed in a Gateway GUI. Normally the senor will not need calibration. It is good practice, however, to calibrate it at least once a year depending on the level of usage.
  • Page 7: Appendix A: Regulatory Information

    NEED HELP? LEAVE THE TECH TO US LIVE 24/7 CHAPTER 1: HEADLINE TECHNICAL APPENDIX A: REGULATORY INFORMATION SUPPORT 1.877.877.2269 A.1 FCC STATEMENT This equipment has been tested and found to comply with the regulations for a Class B digital device, pursuant to Part 15 of the FCC Rules.
  • Page 8 NEED HELP? LEAVE THE TECH TO US LIVE 24/7 CHAPTER 1: HEADLINE TECHNICAL APPENDIX A: REGULATORY INFORMATION SUPPORT 1.877.877.2269 A.4 NOM STATEMENT 1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado. 2.
  • Page 9: Appendix B: Disclaimer/Trademarks

    B.1 DISCLAIMER Black Box Corporation shall not be liable for damages of any kind, including, but not limited to, punitive, consequential or cost of cover damages, resulting from any errors in the product information or specifications set forth in this document and Black Box Corporation may revise this document at any time without notice.
  • Page 10 NEED HELP? LEAVE THE TECH TO US LEAVE THE TECH TO US LIVE 24/7 LIVE 24/7 TECHNICAL TECHNICAL SUPPORT SUPPORT 1.877.877.2269 1.877.877.2269 © COPYRIGHT 2016 BLACK BOX CORPORATION. ALL RIGHTS RESERVED. © COPYRIGHT 2022. BLACK BOX CORPORATION. ALL RIGHTS RESERVED. EME1D1-005-R2_USER_REV1.PDF...

Table of Contents