Download
Share
Print this page
Yaesu FT-2400H User Manual
  1. Manuals
  2. Brands
  3. Yaesu Manuals
  4. Transceiver
  5. FT-2400H
  6. User manual
Yaesu FT-2400H User Manual

Yaesu FT-2400H User Manual

Paging transceivers
Hide thumbs Also See for FT-2400H:

Advertisement

Quick Links

Download this manual

Advertisement

loading

Related Manuals for Yaesu FT-2400H

Summary of Contents for Yaesu FT-2400H

  • Page 2 A03590001 have your receiver stay quiet until your code is received (from any standard DTMF- equipped transceiver). When a cali is received, the FT-2400H displays the calle r's code, Controls & Connectors and a paging beeper can be set to sound and even to respond to the cali automatically.
  • Page 3 (2) Microphone Jack To open the flip-down door, pry the right edge (next to the selector knob) out gently with This 8-contact modular jack accepts trans-mit audio, tone cali (burst) or dial/memory a fingertip. To close the door, press upwards on the bottom edge of the door at its center. selection and scanning control from the mi-crophone, and provides receiver audio for a Do not try to cióse the door by pushing from the front.
  • Page 4 - Before connecting the transceiver, check the voltage at the battery termináis while rev-ving The FT-2400H is designed for use only with an antenna having an impedance near 50 ohms the engine. If it exceeds 15 volts, adjust the car regulator before proceeding.
  • Page 5 NEGATIVE (-) terminal. If you need to extend the power cable use #14 AWG or with a versión A FT-2400H, duplicates the D / MR, button on the front panel of the larger insulated, stranded copper wire. Connect the cable to the transceiver pigtail only after transceiver.
  • Page 6 ("BUSY" not displayed), and squeeze the PTT switch se-lect sequentially from the stored memories. The FT-2400H gives you 31 memories, each on the microphone while talking across the front of it. During transmission, "TX" appears at of which can store repeater shift and direction, CTCSS settings, and sepárate receive and...
  • Page 7 (manually, The FT-2400H offers 31 memories, labelled 1 ~ 28, C, L and U. Each can initially store the or by ARS) in the dial mode. For repeaters that require an odd split, you can either program a current operating data from the dial mode or a retuned memory.
  • Page 8 To confirm that this worked, turn the selector knob to change the dial frequency (to any- twice. At the first press, the display will return to the memory frequency. After the second thing), then press D / MR, to change from dial to memory mode. The numeral 5 should press, the memory name will be displayed —...
  • Page 9 To change the scan-resume mode (when not scanning), press F/W -» A/N STEP. A "P" or you may not always want to use the same memories. With the FT-2400H, you can select and "5" in the memory box indicates the current mode. If you want to change it, press F/W alter which memories are available during memory selection and scanning without having to momentarily.
  • Page 10 of memories L and U is the selected channel step size. Therefore the frequencies stored in either after a 5-second pause, or after the carrier drops (see page 22). To cancel priority both memories /. and U are rounded down to the nearest 100 kHz to determine the actual monitoring manually, press D / MR.
  • Page 11 The display also shows either "P" (for DTMF pager) or "b" (for CTCSS Bell) in the memory the same 3-digit DTMF sequence, sent automatically by the FT-2400H at the start of every box, indicating to which response mode the displayed ringer length setting applies. Press ""j transmission.
  • Page 12 your ID, in Code Memory 1. You can store up to six other Individual Codes of stations you frequency display now, or you can store other code memories in the same way: press MHZ call often, in Code Memories 2 - 7. When someone else transmits your Individual Code your PRI or the microphone buttons again to get the Code Memory number in the memory box display shows Code Memory "0"...
  • Page 13 (to display a Although basic operation of the FT-2400H is simple, some of the newer features may seem blinking 1 in the memory box). If, while you were doing this, he just changed from paging to somewhat complicated at first.
  • Page 14 Packet Radio The FT-2400H has three levels of resetting: memory-only, all-setting soft reset, and all-set- Packet radio operation with the FT-2400H requires a later-model tnc with a PLL-tpe BCD ting hard reset: circuit, since there is no readily-accessible squelch status output from the radio to tell the tnc To reset only the memories, hold the F/W and D/MR buttons while switching the set on.