Page 1
The information in this document contains privileged and confidential information. It is intended only for the use of those authorized by Akai Professional. If you are not the authorized, intended recipient, you are hereby notified that any review, dissemination, distribution or duplication of this document is strictly prohibited.
Page 2
Your purchase of the Manual shall be for your own ultimate use and shall not be for purposes of resale or other transfer. As the owner of the copyright to the Manual, Akai Professional does not give you the right to copy the Manual, and you agree not to copy the Manual without the written authorization of Akai Professional.
Page 3
The exclamation point inside a triangle is intended to alert the user to the presence of important operating, maintenance and servicing instructions in the literature which accompanies the product. REPAIR BY ANY PERSON OR ENTITY OTHER THAN AN AUTHORIZED AKAI PROFESSIONAL SERVICE CENTER WILL VOID THE AKAI PROFESSIONAL WARRANTY.
Page 4
8. Mounting. The product should only be used with a rack which the manufacturer recommends. The combination of the product and rack should be moved carefully. Quick movements, excessive force or uneven surfaces may overturn the combination which may damage the product and rack combination.
DISASSEMBLY PROCEDURE DISASSEMBLE THE BOTTOM PANEL (A) REMOVE 9 PCS SCREW FROM THE.BOTTOM (B) REMOVE 4 PCS SCREW FROM THE BOTTOM. (C) REMOVE 9 PCS SCREW FROM THE REAR PANEL HOUSING. (D) REMOVE 4 PCS NUT /2PCS KNOB FROM THE REAR PANEL PCB ASS’Y (Fig1) DISASSEMBLE THE H/P PCB (A) REMOVE 2 PCS KNOB FROM THE H/P PCB ASS’Y..
Page 7
. DISASSEMBLE THE SUPER CAP PCB ASS’Y. (A)REMOVE 4 PCS SCREW FROM THE SUPER CAP PCB ASS’Y.. (Fig3) . DISASSEMBLE THE RA PCB ASS’Y (A) REMOVE 4 PCS SCREW FROM THE RAPCB ASS’Y. (Fig4)
Page 8
DISASSEMBLE THE AZ01 PCB ASS’Y (A) REMOVE 4 PCS KNOB FROM THE AZ01 PCB ASS’Y (Fig5) DISASSEMBLE THE CV PCB ASS’Y (A) REMOVE 3 PCS SCREW FROM THE CV PCB ASS’Y.. (Fig6)
Page 9
DISASSEMBLE THE TOP RIGHT PCB ASS’Y (A)REMOVE 6 PCS SCREW FROM THE TOP RIGHT PCB ASS’Y.. (Fig7) DISASSEMBLE THE ADAPTER PCB ASS’Y (A)REMOVE 2 PCS SCREW FROM THEADAPTER PCB ASS’Y.. (Fig8)
Page 10
DISASSEMBLE THE TOP LEFT PCB ASS’Y (A)REMOVE 9 PCS SCREW FROM THE TOP LEFT PCB ASS’Y.. (Fig9) DISASSEMBLE THE NAMEPLATE (A)REMOVE 7 PCS SCREW FROM THE NAMEPLATE (Fig10)
Page 11
DISASSEMBLE THE PAD HOLDER (A)REMOVE 13 PCS SCREW FROM THEPAD HOLDER (Fig11) DISASSEMBLE THE TOP AND VR PCB ASS’Y (A)REMOVE 8 PCS KNOB FROM THE VR PCB ASS’Y (B)REMOVE 8 PCS NUT FROM THE VR PCB ASS’Y (C)REMOVE 8 PCS WASHER FROM THE VR PCB ASS’Y (D) REMOVE 3 PCS SCREW FROM THEOLED PCB ASS’Y..
Page 12
DISASSEMBLE THE OLED PCB ASS’Y (A)REMOVE 6 PCS SCREW FROM THE OLED PCB ASS’Y (B)REMOVE 3 PCS SCREW FROM THE OLED PCB ASS’Y (Fig13) DISASSEMBLE THE TOP PCB ASS’Y (A)REMOVE 30 PCS SCREW FROM THE TOP PCB ASS’Y (Fig14)