Table of Contents
Advertisement
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
(2) Press the
l m
or
M L
(3) Press the
ENTER/YES "R"
(4) When access completes, the display changes to "C1 =
Note: The numbers " " displayed show you error rates and ADER.
2. Changing the parts to be played back
(1) Press the
ENTER/YES "R"
"CPLAY MID" t "CPLAY OUT" t "CPLAY IN"
When pressed another time, the parts to be played back can be moved.
(2) When access completes, the display changes to "C1 =
Note: The numbers " " displayed show you error rates and ADER.
3. Ending the continuous playback mode
(1) Press the
MENU/NO "R"
(2) Press the
(MD) button and take out the disc.
A
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)
1. Entering the continuous recording mode
(1) Set a recordable disc in the unit.
(2) Press the
or
l m
M L
(3) Press the
ENTER/YES "R"
(4) When access completes, the display changes to "CREC (
Note: The numbers " " displayed shows you the recording position addresses.
2. Changing the parts to be recorded
(1) When the
ENTER/YES "R"
"CREC MID" t "CREC OUT" t "CREC IN"
When pressed another time, the parts to be recorded can be changed.
(2) When access completes, the display changes to "CREC (
Note: The numbers " " displayed shows you the recording position addresses.
3. Ending the continuous recording mode
(1) Press the
MENU/NO "R"
(2) Press the
A
(MD) button and take out the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN
: 40h cluster
MID : 300h cluster
OUT : 700h cluster
Note 2: The
MENU/NO "R"
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
4-5-3. Non-Volatile Memory Mode (EEP MODE)
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If the unit entered this mode accidentally, press the
4-6.
FUNCTIONS OF OTHER BUTTONS
Function
H S (MD)
s (MD)
M L
l m
CLEAR "R"
PLAY MODE/TUNING MODE
DISP "R"
A (MD)
REPAET
28
button and display "CPLAY MODE".
button to change the display to "CPLAY MID".
button during continuous playback to change the display as below.
button. The display will change to "CPLAY MODE".
button and display "CREC MODE".
button to change the display to "CREC MID".
button is pressed during continuous recording, the display changes as below.
button. The display changes to "CREC MODE" and
button can be used to stop recording anytime.
Sets continuous playback when pressed in the STOP state. When pressed during continuous playback, the tracking
servo turns ON/OFF
Stops continuous playback and continuous recording
The sled moves to the outer circumference only when this is pressed
The sled moves to the inner circumference only when this is pressed
Switches between the pit and groove modes when pressed
Switches the spindle servo mode (CLV-S y CLV-A)
Switches the displayed contents each time the button is pressed
Ejects the disc
Releases the test mode
AD =
".
AD =
".
[ REC]
)" and
z
indicator lights up.
[ REC]
z
indicator goes off.
[ REC]
)" and
z
indicator lights up.
[ REC]
indicator goes off.
z
button immediately to release it.
MENU/NO "R"
Contents
Advertisement
Table of Contents
