Digital organ sx-f100 operating manual (168 pages)
Summary of Contents for Panasonic SX-PX554
Page 1
ORDER NO. EMID0004007C0 Digital Piano SX-PX554 / SX-PX554M (P) U.S.A. (PC) Canada (PY) Mexico (EX) Norway, Sweden, Denmark, Finland, Spain, Portugal, Greece, South Africa (EZ) Germany (EG) Switzerland, Italy, Austria, Holland, Belgium, France (EB) the United Kingdom (GN) Australia, New Zealand...
Page 2
88 KEYS KEYBOARD 64 NOTES MAX. POLYPHONY 18 SOUNDS: CONCERT SOUND GRAND, POP GRAND, UPRIGHT, E PIANO 1, E PIANO 2, HARPSI, VIBES, STRINGS, VOCAL, ORGAN PRESETS SOFT, SOSTENUTO, SUSTAIN PEDAL MELLOW, BRIGHT (5 STEPS) BRILLIANCE Supported DIGITAL EFFECT Supported (ROOM, STAGE, DIGITAL REVERB HALL, CONCERT) LIGHT, NORMAL, HEAVY...
Page 3
1. WARNING To prevent the risk of fire, smoke, or electrical shock and to ensure safe operation, please be sure to follow the safety guidelines below. 1. At places where special caution is required, the necessary safety precautions are clearly labeled or printed, for example, on the cabinet, or on the part concerned.
6.5 mm.). 2. SAFETY PRECAUTION 2.1. Safety precaution 1. Before servicing, unplug the power cord to prevent an electric shock. 2. When replacing parts, use only the manufacturer’s recommended components for safety. 3. Check the condition of the power cord. Replace if wear or damage is evident.
Page 5
To prevent the piano unit from falling off the stand, secure it firmly with the screws. 1. Assemble the right and left planks - Assemble the right and left planks to the pedal box with the 4 brass -colored screws. - Loosen the pedal cord, stowed on the inner side of the pedal box, and extend it.
- Place the piano body on the stand and secure it with 4 black screws A. Figure-4 4. Connect the pedal cord and power cord - Connect the pedal cord and power cord to the terminals located on the rear of the piano unit as shown below. - Secure the pedal cord to the clamps as shown in the figure.
Figure-6 6. PARTS LOCATION Figure-7 7. DISASSEMBLY INSTRUCTIONS 7.1. Removing the top cover 1. Remove the top cover mounting screws (A 4 pcs.) as shown in Figure-8. 2. Slide the top cover forward and lift up (as shown by the arrows). 7.2.
Page 8
1. Remove the top cover (see step “Removing the top cover”). 2. Match the gears of the keyboard cover with the notches in the guide rail, and lift up the keyboard cover as shown in Figure-8. Figure-8 7.3. Removing the control panel - Pull out the connectors on the control panel.
Page 9
2. Remove the keyboard assembly mounting screws located on the bottom of the cabinet (A 10 pcs.) as shown in Figure-10. Figure-10 7.5. Key(s) Disassembly 1. Remove the keyboard assembly (see step “Removing the keyboard assembly”). 2. While inserting a thin plate to press down a claw, push the rear of the key forward to disengage the key claw from the chassis.
1. Insert the front part of the key into the chassis. 2. Insert the plate spring into the hammer notch as shown in Figure - 3. While slowly lowering the key into the chassis, insert the plate spring into the notch at the rear of the key. 4.
”). 2. Pull the MAIN VOLUME knob. 3. Remove the CPL P.C.B. mounting screws (H 10 pcs., I 3pcs., J 1 pc., and K 1 pc.). CPR P.C.B. 1. Remove the control panel (see step “Removing the control panel ”). 2.
Page 13
TEST MODE Procedure 1. Connect the CHECKING DEVICE to CN9 on the MAIN P.C.B., and turn on the CHECKING DEVICE MAIN RAM (IC8,9), ROM 2. Turn on the power switch. (IC6) check 1. Connect the CHECKING DEVICE to CN9 on the MAIN P.C.B. (the Checking Device switch should CPU (IC1) check 2.
TEST MODE Procedure 1. Press and hold the two E keys shown below, and then turn on the power switch. Wave ROM check MAIN 2. Select the POP GROUND sound. MAIN: IC12, IC18 3. Reduce the MAIN VOLUME level low enough. When set to the self-diagnostic mode, the Wave ROM outputs a sine The Wave ROMs correspond to the keyboard keys as shown in the to the right.
TEST MODE Procedure Control Panel buttons Press and hold the two F keys shown below, and then turn on the LED lighting check switch. Press the buttons on the control and confirm that the corresponding light. Control Panel LED Press and hold the two G keys shown below, and then turn on the display check switch.
Page 17
output as a sine wave to facilitate the servicing check. 9.2. Important safety notice - Components identified by a mark have special characteristics important for safety. - When replacing any of these components, use only manufacture’s specified parts. 9.3. Symbolic marks The symbolic marks for resistors and capacitors which used in this circuits are classified as following Table-1...
SYMBOL SPECIFICATION TYPE Non-Polarized Electrolytic ECEA_KN_type Capacitors Non-Polarized Electrolytic (for ECEA_Y_type Network system) Tantalum Solid Electrolytic ECS_type Capacitors Metallized Plastic Film Capacitors ECQV_type (TF Series) Temperature Compensating ECC_type Ceramic Capacitors High-Dielecytric Constant Ceramic ECK_type, ECR_type Capacitors Axial Lead Ceramic Capacitors ECB_type Metallized Polyester Film ECQ_EW_type...
Page 19
10.2. Measuring condition of FAJSP P.C.B. Check Point 3 - 8 Set to the Self-diagnostic Mode followings. - While pressing two E keys simultaneously, turn on the power switch. - SOUND: CONCERT GRAND - MAIN VOLUME: Max. - Keyboard: A Check Point 1,2 Set to the Initial mode (refer to “OWNERS...
Page 20
11. SCHEMATIC DIAGRAM 12. PRINTED CIRCUIT BOARD 12.1. MAIN, FAJSP, CPL P.C.B. 12.2. CPR, MKB1, MKB2, PKB, COM, HP P.C.B. 13. BLOCK DIAGRAM 14. WIRING CONNECTION DIAGRAM 15. REPLACEMENT PARTS LIST Notes: *Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardant (resistors), high-quality sound (capacitors), low-noise (resistors), etc.
Page 21
*MAIN, FAJSP, CPL, CPR, MKB1, MKB2, COM and HP in Remarks indicate the Circuits and P. C. B.s. If the same Ref. No. is found in the replacement parts list, check those indications in the Remarks. Ref. No. Part No. Part Name &...
Page 22
Ref. No. Part No. Part Name & Description Remarks QKQGN995AAZK LEFT PLANK QKQGN995ABZK LEFT PLANK SX-PX554M QKQGN996AAZK RIGHT PLANK QKQGN996ABZK RIGHT PLANK SX-PX554M QAQG033AAK LEFT LEG ASS'Y QAQG033ABK LEFT LEG ASS'Y SX-PX554M 31-1 SHRG2130B-K FOOT 31-2 XTB4+16A SCREW QAQG034AAK RIGHT LEG ASS'Y QAQG034ABK RIGHT LEG ASS'Y SX-PX554M...
Page 23
Ref. No. Part No. Part Name & Description Remarks QMWG6020AA RUBBER SWITCH(12 PCS,ON O XNS12FZ XTT4+10A SCREW XTB4+12A SCREW XTW3+8J SCREW XTN4+16F SCREW WITH WASHER XTT4+14A SCREW XTB35+14A SCREW XYN4+F16FZ SCREW XTB35+10A SCREW XTW3+10Q SCREW XTV3+20JFZ SCREW XTT4+12AFZ SCREW XYA35+JA12 SCREW XYN3+C8FZ SCREW...
Page 24
Ref. No. Part No. Part Name & Description Remarks ECRR1H104ZF 0.1UF ECKF1E473ZV 0.047UF ECRF1H104ZF 0.1UF MKB1 ECUV1C224KBX 0.22UF MAIN ECKF1E473ZV 0.047UF ECQU2A104MN 0.1UF,250V FJASP ECUV1C224KBX 0.22UF MAIN QCBG1H104ZFA 0.1UF ECBT1E223ZF5 0.022UF ECRF1H104ZF 0.1UF ECRR1H104ZF1 0.1UF MAIN ECA1VM472E 4700UF,35V FJASP ECEA0JKA470 47UF,6.3V MKB1 ECEA0JKS101B...
Page 26
Ref. No. Part No. Part Name & Description Remarks ECUV1H101JG 100PF MAIN ECQG1H682KZT 0.0068UF FJASP ECUV1H104ZFX 0.1UF MAIN ECQG1H332KZT 0.0033UF FJASP ECUV1H104ZFX 0.1UF MAIN ECEA1CKA470B 47UF,16V MAIN ECQG1H222KZT 0.0022UF FJASP ECQB1H103JF3 0.01UF FJASP EECS5R5V105 1F,5.5V MAIN ECEA1HKN010B 1UF,50V FJASP ECUV1H104ZFX 0.1UF MAIN ECQB1H473JF3...
Page 27
Ref. No. Part No. Part Name & Description Remarks ECUV1H104ZFX 0.1UF MAIN ECBT1C222MR5 0.0022UF FJASP ECUV1H104ZFX 0.1UF MAIN ECBT1C222MR5 0.0022UF FJASP ECCR1H104ZF1 0.1UF FJASP ECUV1H104ZFX 0.1UF MAIN ECEA1CKA100B 10UF,16V MAIN C63,64 ECUV1H104ZFX 0.1UF MAIN ECCR1H221J5 220PF FJASP ECEA1CKA100B 10UF,16V MAIN ECEA1HKNR47B 0.47UF,50V MAIN...
Page 28
Ref. No. Part No. Part Name & Description Remarks SJPG1JS120A CONNECTOR FJASP SJPG1JS070A CONNECTOR MAIN SJPG1JS070A CONNECTOR FJASP SJPG1310A CONNECTOR FJASP QJUG00212AA CONNECTOR MKB1 SJPG1340A CONNECTOR FJASP SJPG1JS100A CONNECTOR MAIN QJUG01408AA CONNECTOR MKB1 SJPG1JS040A CONNECTOR MAIN ERA1502V5 DIODE ;FJASP MA165 DIODE MKB1 MA165TA5...
Page 29
Ref. No. Part No. Part Name & Description Remarks D14,15 MA165 DIODE MKB1 MA165TA5 DIODE FJASP MA8056MTX ZENER MAIN MA165 DIODE MKB1 MA165TA5 DIODE FJASP MA8047HTX Z.DIODE MAIN MA111TX DIODE MAIN MA165 DIODE MKB1 MA165TA5 DIODE FJASP MA165TA5 DIODE MA111TX DIODE MAIN MA165...
Ref. No. Part No. Part Name & Description Remarks QEXSS05028A CONNECTOR WITH WIRE QEXGSS6030B CONNECTOR WITH WIRE QEXGSS10015A CONNECTOR WITH WIRE QEXGSS07010A CONNECTOR WITH WIRE QEXGSS12010A CONNECTOR WITH WIRE QEXGVH04075F CONNECTOR WITH WIRE QEXGSS16022C CONNECTOR WITH WIRE QEXGVH05055C CONNECTOR WITH WIRE QEXGSS06105A CONNECTOR WITH WIRE QEXGVH03105B...
Page 60
2SD601AQTX +15V 2SB709ARTX R113 R114 4.7K MA8056MTX A B C A B C D E F G H I J K L 100x4 P70/PG00 P71/PG01 P72/PG02 P61/CS1 P73/PG03 P62/CS2 P20/A16 P74/PG10 P63/CAS P21/A17 P75/PG11 P64/RAS P22/A18 P76/PG12 P65/REFOUT P23/A19 P77/PG13 P24/A20 P25/A21 P80/TXD0...
Page 62
A B C N H I G J F D K C B A H A G B F +3.3 TG CLOCK NRSTSG RAMDT2 NRSTCPU RAMDT4 RAMDT3 SDIREV SDOREV SDICH0 SDOCH0 SDIDRY SDODRY TEMODE3 TEMODE2 2.2K DIVOUT SDOMIX LRCK IC10 ROMDT11 D97315GD201 ROMDT4...
Page 63
TG CLOCK QLQGT1B100MA QLBG005A QLBG005A QLBG005A IC15 TC7W04FTE12L (TRIPLE INVERTER) A B C M N H I G J F D K C B A +VCC 1 2 3 4 5 6 7 8 R65 1M +3.3 H A G B F QSXG1A1128A NRSTSG RAMDT2...
Page 66
FJASP CIRCUIT PRODUCTS FOR X XS XT XD XA POWER TRANSFORMER QSRGT006AA BLUE 4700P BLACK JK9 L1 POWER 100uHx2 CORD BLUE ERA1502V5 ERA1502V5 PRODUCTS FOR P PC PY 4700P JK9 L1 100uHx2 LINE OUT L 0.0022 LINE OUT R /R+L 0.0022 PRODUCTS FOR OTHERS 4700P...
Page 82
COM P.C.B. MAIN P.C.B. QEXGSS07010A QEXGSS12010A QEXGST160608 QEXGHVH02055C CORE CORE 6.5cm,8 QEXGSS16022C CPL P.C.B. 14cm,6 CORE MKB1 P.C.B. QEXGSS16022C QEXGSS16022C HP P.C.B.
Page 83
AC CORD FJASP P.C.B. AC IN POWER TRANSFORMER POWER SWITCH QEXGVH03105B QEXGVH02040B 6.5cm,8 CPR P.C.B. 14cm,6 MKB2 P.C.B. PKB P.C.B.
Page 84
Press one of the SOUND buttons to select the desired sound. Each sound features Touch Response, which increases the volume when the keyboard is DIGITAL REVERB applies a played harder. reverberation effect to the sound. Select The sounds can be mixed when two from four echo types—ROOM, STAGE, SOUND buttons are pressed simultaneously.
Page 85
The BRILLIANCE allows you to select the brightness of the sound from 5 settings. If either of the buttons is pressed once, the current setting value will appear on the display, and it can then be changed. The keyboard touch (Touch Response) can be Pressing the BRIGHT button increases the changed to match your type of playing.
Page 86
(On the back of piano) LINE OUT AUX IN MIDI COMPUTER PEDAL IN R + L R + L MIDI PEDAL IN COMPUTER Connect the cord from the included stand to this By connecting this terminal to the serial port of terminal.
Page 87
Phenomenon Remedy No sound is produced when the No sound is produced if the MAIN VOLUME is set to MIN. keyboard is played. Use the sliding control to set the volume to an appropriate level. If the MIDI LOCAL CONTROL is set to off, set it to on. Nothing is shown on the display.
Page 88
Digital piano [ SX-PX554/M ] Transmitted Recognized Remarks Function Basic Default 1-16 memorized 1-16 Channel Changed 1-16 1-16 1, 3 memorized Default × × Mode Messages Altered Note 0-127 *21-108 Number True voice *0-127 〇 〇 Velocity Note ON × ( 9nH: V=0) ×...