Table of Contents
Advertisement
Quick Links
50 Inch Electric Fireplace
CONSUMER SAFETY INFORMATION
1.
Read this manual before installing and operating this appliance.
2.
Failure to follow these instructions may result in electric shock, fire property,
or personal injury.
3.
Do not store or use gasoline or other flammable liquids in vicinity of this appliance.
User Manual
Advertisement
Table of Contents
Related Manuals for Dimplex X40003BK
Summary of Contents for Dimplex X40003BK
- Page 1 50 Inch Electric Fireplace User Manual CONSUMER SAFETY INFORMATION Read this manual before installing and operating this appliance. Failure to follow these instructions may result in electric shock, fire property, or personal injury. Do not store or use gasoline or other flammable liquids in vicinity of this appliance.
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION! WARNING Read all instructions before using this heater! This heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater, and keep them away from the sides and rear. - Page 3 NEVER use a wall hung bracket from another manufacturer. This product is not intended to be a primary heat source. It is for supplemental heat only. INDOOR use only! NEVER use this heater outdoors! Doing so may result in electric shock! Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ALWAYS turn this heater off before unplugging it from the outlet.
-
Page 4: Grounding Instructions
Grounding instructions： This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 60.1. An adapter as shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. -
Page 5: Parts & Hardware
D - Decorative B - Wood Screws C-Drywall anchors E - Log set Crystals A - Fireplace Remote control Specification and Dimension PRODUCT DIMENSIONS Model Number 50” 19” 5.1” 46.5” 18” 10.6” 43.3” X40003BK 127CM 48CM 13CM 118CM 45.5CM 27CM 110CM... - Page 6 PREPARATION Your appliance is a wall hung, recessed and /or mantel installed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas. NOTE： Follow all National and local electrical codes. MINIMUM CLEARANCE TO COMBUSTIBLES Measurements are taken from the glass front.
- Page 7 ( A ) STEP A. Selection a dry wall to open a hole for fireplace box. Size of hole as below chat. Framing Hole Size Model Number X40003BK 47.5”(120.6cm) 19”(48.3cm) Wall Anchors (4pcs) ( B ) STEP B. Punch 4 holes around the wall and install 4 Drywall anchors...
- Page 8 （C） （E） The fourth screw from top to bottom STEP C. Take off the screws （The fourth screw from top to bottom) in both sides of fireplace. Figure (C) STEP D. Remove packaging attachments from the log set. 1.Remove the front grass. 2.Remove the pear cotton block.
- Page 9 Wall Hung Installation WARNING Only qualified person can perform the installation. Due to the many different materials used on different walls, it is highly recommended that you consult your local builder before you install this appliance on the wall. 1.You can see 2 clips on the back of the device 16”...
- Page 10 Logset /Crystal Ember Installation WARNING Only qualified person can perform the installation. The fourth screw from top to bottom 1.Remove the screws (The fourth screw from top to bottom) on both side of the device to remove the front grass. 2.Take out the logset inside.
- Page 11 WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure do to so could result in electric shock, fire, serious injury, or death. OPERATION INSTRUCTION： Plug in a power plug hear a long buzzer and the electric fireplace is in standby mode. Press the POWER key on the keyboard to show red, and the rest of the display is not displayed.
- Page 12 High Temperature & Low Temperature Setting: Press “HEATER” button for 3 seconds to switch the temperature between °F and °C ( Note: The switch function is not available for different batches of fireplaces.) The initial default temperature is 72°F. If you need the fireplace runs the low temperature heating mode, press the HEAT button on the touch panel or remote control to switch your desired mode (Low temperature mode).
- Page 13 Flame Brightness Setting: The flame brightness is on the brightest mode by default. There are 5 flame brightness levels. If you need to adjust the flame brightness, press the "DIMMER" button, the brightness of the LED lamp will become dark, and the display window of digital tube will show the level of the brightness.
-
Page 14: Temperature Limiting Control
14. Screen protection function: The heaters have a screen protection function, If the heaters after working without operation on the keypad or remote control after 30 seconds, the heater will be closed the keypad all display light expect the power on light. The heaters on normal work, if you need wake up the display again, then you only press any button on the keypad or on the remote control then it can be shown again. -
Page 15: Care And Maintenance
CARE AND MAINTENANCE Cleaning ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. -
Page 16: Troubleshooting
Troubleshooting WARNING DISCONNECTED THE APPLIANCE COMPLETELY AND LET COOL PRIOR TO ANY SERVICE. ONLY A QUALIFIED SEVICE PERSON SHOULD SERVICE AND PEPAIR THIS ELECTRIC APPLAINCE. Solution Problem Possible Cause 1.Fireplace turns 1.Fireplace has overheated and 1. Pull the plug, wait 5 minutes to plug it offand will not safety devise has caused back in and turn it on.