Advertisement
2 – Setting Time
MODE button repeatedly until the words
1.
If necessary, press the
SET and CLOCK appear in the upper area of the display.
2.
Press the
+ or – buttons to enter the current time.
NOTE: To go from AM to PM, keep pressing the + or – but-
tons to cycle through the day. You can hold the + or – but-
tons down for 3 seconds to make the time scroll quickly.
MODE button to exit and advance to setting Events.
3.
Press the
3 – Setting Fixed Timed Events
MODE button repeatedly until the words
1.
If necessary, press the
SET, FIXED, ON/OFF EVENT and EVENT 1 appear on the
display.
ENTER button to display ON @ or OFF @
2.
If necessary, press the
(depending on what you want to set).
DAY button to display 12:00 am and all days of the
3.
Press the
week.
4.
Press the
+ or – buttons to enter the time you want to set.
NOTE: To go from AM to PM, keep pressing the + or – but-
tons to cycle through the day. You can hold the + or – but-
tons down for 3 seconds to make the time scroll quickly.
5.
If you want the Event to occur for a combination of days rather
than every day (e.g., weekends only, weekdays only, or indi-
vidual days), press the DAY button again as necessary to cycle
through the individual days or combination of days you want.
NOTE: To choose a combination not shown during cycling
(e.g., Tuesday and Thursday), you must create an individu-
al event for each of the days you want.
ET1725C ONLY
6.
—For a multi-circuit device with loads set
independently, you can choose the load you want the event to
control. The default setting is for both loads, as you can see on
the display. Press the ON/OFF button under a load to remove the
load from the event.
7.
When you have set the event correctly, you have two choices:
-
ENTER button to set the next fixed time event (up to
Press the
28 events).
-
MODE button to exit.
Press the
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole op-
tion, free of charge. This warranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused
by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise
modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs, LED's and batteries; (f) the
finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal
costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD
STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase,
postage prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-
9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.
Operating the Time Switch
Press the MODE button repeatedly to select the desired operating
mode on the display. There are 2 options:
•
AUTO
grammed, turning the circuits ON and OFF at the time(s) set.
•
MANUAL
Switch controls all circuits through the ON/OFF button.
NOTE: You can review or edit any programmed events at any time
by pressing the MODE button repeatedly to return to the appropriate
menu, then following programming instruction provided on this sheet.
OPTIONAL – Deleting (Clearing) an Event
Use this procedure to clear the settings programmed for an event.
1.
If necessary, press the
SET, FIXED, and ON/OFF EVENTS are shown on the display.
2.
Press the
that have been set until you see the event you want to delete.
3.
Press the
4.
Press the
Battery Maintenance
•
Batteries can be easily replaced without removing the Time
Switch mechanism or field wiring.
•
Press in and downward (in the direction of the arrows) on the
battery cover.
•
It is recommended to replace the batteries every 2-3 years with
2 AAA industrial grade alkaline cells as part of normal mainte-
nance on the Time Switch.
•
Be sure to observe battery polarity markings when installing
batteries.
•
No other battery maintenance is required.
LIMITED ONE-YEAR WARRANTY
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
—where the Time Switch follows the events you have pro-
NOTE: You can override programmed events and force the
Time Switch ON or OFF by pressing the ON/OFF button.
—where any events set are disabled and the Time
MODE button repeatedly until the words
ENTER button as necessary to cycle through events
+ or – buttons AT THE SAME TIME to display --:-- --.
MODE button to exit.
158--00xxx
Advertisement
