BAUMOT B 200 Operating Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Operating Manual

Electric Kiln B 200

Table of Contents

Summary of Contents for BAUMOT B 200

Page 1 Operating Manual Electric Kiln B 200...
Page 2: Table Of Contents
TABLE OF CONTENTS Page Important safety information 1.1. General information 1.2. Safety information 1.3. Safety equipment and protective clothing 1.4. Safety information for usage Start-up 2.1. Delivery details 2.2. Operation area/assembly site requirements 2.3. Power source information/RC device 2.4. Firing with the kiln General operating information 3.1.
Page 3: Important Safety Information
1. IMPORTANT SAFETY INFORMATION 1.1. General information It is imperative that the safety information – but also the safety approval markings – be observed in order to avoid potential hazards. It is in your own best interest that you read the following safety information in its entirety prior to starting up the shuttle kiln.
Page 4: Safety Equipment And Protective Clothing
1.3. Safety equipment and protective clothing When opening, loading, or unloading the kiln, the operating personnel must wear protective clothing. The high temperatures emitted can cause injury. The kiln manufacturer cannot be held liable for material damage or bodily injury! 1.4.
Page 5: Start-Up
2. START-UP 2.1. Delivery details The BAUMOT shuttle kiln is generally delivered by a transport company. The delivery must always be inspected for damage to the packaging immediately upon delivery. Should damage be evident, unpack the delivery together with the driver and inspect the goods for signs of damage.
Page 6: Firing With The Kiln
2.4. Firing with the kiln The Baumot kiln’s regulator is pre-set at the factory to the exact times and temperatures necessary for firing ceramic diesel particle filters. The preheating phase takes approx. 1 hour, during which the temperature is increased up to 550° C with a subsequent holding time of 3.5 or 8 hours. Therefore, the firing time without the cooling phase takes either 4.6 or 9 hours .
Page 7: General Operating Information
3. GENERAL OPERATING INFORMATION 3.1. Operating the control unit Process controller Jumo cTRON 316. 3.2. Entering program/Starting program Entering program set value of final temperature: Button Description Display To access the “USER” menu, “USER” appears in the green display press the “P” button. Button Description Display To access the “set temperature”...
Page 8 Button Description By pressing the ▲ button, you can TIP: The set value can also be increase the set value, and with changed during the firing operation the ▼button, you can decrease the with the ▲ and ▼ buttons. value. Button Description To save the entered program values, press the “P”...
Page 9 Programing holding time after reaching final temperature Time selector switch You can select the duration of the holding time of the programmed final temperature with the aid of the time selector switch: “3 h” position: Holding time of final temperature is 3 hours “5 h”...
Page 10: The Exhaust Air Hole
Do not look directly into the exhaust air hole when the kiln is hotter than 150°C. This can cause injury to the face. Operating personnel must wear adequate protective clothing! Baumot GmbH will not accept liability for personal injury or material damage!
Page 11: Proper Handling During Firing
Unauthorised persons may not remain in the vicinity! The high temperatures being released can cause burns and injury as well as lead to the premature closing of the kiln. Baumot GmbH will not accept liability for personal injury or material damage!
Page 12: Maintenance/Care And Cleaning
4. MAINTENANCE/CARE and CLEANING Maintenance procedures Please note: Voltage carrying components - Risk of fatal injury! The kiln must be disconnected from the power source! Authorised personnel may not begin the maintenance procedures until a safety inspection has been carried out . Care and cleaning Ensure that no foreign matter is allowed inside the firing chamber or onto the heating elements.
Page 13: Trouble-Shooting Tips
TROUBLE-SHOOTING TIPS 5.1. The control unit cannot be switched on. • Check if the power connector for the kiln is plugged into the mains. • Check the fuses of the building’s power supply that protect the connection box of the kiln. •...
Page 14: Warranty Obligation
6. WARRANTY OBLIGATION We refer to the legal warranty obligation with a warranty period of 24 months guarantee as of the invoice date: Along with the heating coils (components subject to wear), the following items are also not included: • Damage caused by the customer. •...
Page 15: Property Rights/Trademarks/Disclaimer
8. SERVICE ADDRESSES If you have questions regarding your kiln, replacement parts or additional accessories, please contact your specialist dealer or Baumot GmbH. We wish you much success and only good firing results! Your Baumot-Team...