Summary of Contents for ConSenses Accelerometer BA Series
- Page 1 Assembly Instructions Accelerometer BA... ConSenses GmbH Arheilger Weg 11 D-64380 Roßdorf Germany E-mail: info@consenses.de...
- Page 2 The information presented in this document reflects the current state of knowledge. ConSenses reserves the right to make technical changes. Liability for consequential damages resulting from the use of ConSenses products is excluded.
-
Page 3: Table Of Contents
Failure to observe safety instructions may result in damage to persons or the machine. Therefore, please ob- serve the safety instructions before each use. If you have any questions about this product, please contact the manufacturer: ConSenses GmbH, Arheilger Weg 11, D-64380 Roßdorf, Germany E-mail: info@consenses.de... -
Page 5: Scope Of Delivery And Accessories
1. Scope of delivery and Accessories Labeling: The plug connection on the accelerometer is detachable. Different measuring ranges are available under the following order numbers: Order number Description 03.90203 Accelerometer BA with measuring range ± 50 g 03.90204 Accelerometer BA with measuring range ± 100 g 03.90205 Accelerometer BA with measuring range ±... -
Page 6: Operating Principle And Application Notes
2. Operating Principle and Application Notes The accelerometer‘s sensor is MEMS-based. MEMS stands for “Micro-Electro-Mechanical Systems”. In this case, the measurement principle is capacitive and offers the following advantages: The basic sensor system (in contrast to piezo-based acceleration sensors) do not represent an uncon- ✓... - Page 7 limit, the over-range output (black, 0...5 V) signals for 0.5 ms that the measuring range has been exceeded. The MEMS sensor then checks whether operation is within the measuring range limits. In the figure, this is not the case again until a few 0.5 ms cycles later, whereupon the sensor registers the correct values again within a 0.5 ms cycle.
-
Page 8: Safety Instructions
3. Safety Instructions 3.1. Intended Use The accelerometers BA are sensors for the metrological detection of vibrations on components or machine elements within the operating limits of the sensor. Any other use is not in accordance with the intended use. To ensure safe operation, the product may only be used in accordance with the information in these assembly instructions and in compliance with the following safety regulations and the technical data provided. -
Page 9: Supplementary Safety Precautions
3.4. Supplementary Safety Precautions As passive sensors, accelerometers cannot perform any safety-relevant functions. This requires additional components and equipment for which the installer and operator are responsible. Electronics that process such a measurement signal must be designed in such a way that no consequential damage can occur if a measure- ment signal fails. -
Page 10: Conditions And Preparations On Site
4. Conditions and Preparations on Site Ensure that the accelerometers BA are protected from adverse conditions such as salt water, snow, rain. or ice. Protect the contact points from contamination and do not touch the terminals. A constant temperature within the operating range affects the sensitivity of the accelerometers only to a small extent. -
Page 11: Mechanical Installation
5. Mechanical Installation 5.1. General Installation Guidelines Handle the accelerometers gently. You thus prevent damage that can impair the mounting of the accelerome- ter or signal cable as well as the measurement signal. The signal interface connection should be easily acces- sible. -
Page 12: Connection
Please pay attention to the following pin assignment of the connection cable: If you obtain cables from ConSenses original accessories, the following specifications apply to the shielded connection cable with open ends: that the cable is moved as little as possible and preferably rests... -
Page 13: Technical Data
7. Technical Data 7.1. Dimensions The two through holes for the fastening screws have a diameter of 5.5 mm. 7.2. Series-specific Data Measuring range ± 50 ± 100 ± 200 ± 500 Sensitivity mV/g 7.3. General Data Operating temperature range °C -20 …... -
Page 14: Declaration Of Conformity
8. Declaration of Conformity ConSenses GmbH, Arheilger Weg 11, D-64380 Roßdorf, Germany declare under our sole responsibility that the product Accelerometer in the versions BA… complies with the following provision of the European Union: Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on...