Table of Contents
Advertisement
IGSV-VTB, VSG-0309
STOCKING
Improper temperature and lighting will cause serious
product loss. Discoloration, dehydration and spoilage can
be controlled with proper use of the equipment and
handling of product. Product temperature should always
be maintained at a constant and proper temperature.
This means that from the time the product is received,
through storage, preparation and display, the tempera-
ture of the product must be controlled to maximize life
of the product. Hussmann cases were not designed to
"heat up" or "cool down" product—but rather to
maintain an item's proper temperature for maximum
shelf life. To achieve the protection required always:
1. Minimize processing time to avoid damaging
temperature rise to the product. Product should be
at proper temperature.
2. Keep the air in and around the case area free of
foreign gasses and fumes or food will rapidly
deteriorate.
3. Maintain the display merchandisers temperature
controls as outlined in the refrigerator section of
this manual.
4. Do not place any product into these refrigerators
until all controls have been adjusted and they are
operating at the proper temperature. Allow
merchandiser to operate a minimum of 6 hours
before stocking with any product.
5. When stocking, never allow the product to extend
beyond the recommended load limit. Air discharge
and return air flue must be unobstructed at all
times to provide proper refrigeration.
6. There are vents located at the base of the front of
the glass, just above the front rail. These vents
supply a continuous, gentle flow of air across the
front glass which inhibits condensation. Do not
place any signs or other restrictive objects on the
front of the refrigerator that will block these vents.
7. Keep the service doors closed (when applicable).
Refrigeration performance will be seriously
affected if left open for a prolonged period of time.
8. Avoid the use of supplemental flood or spot
lighting. Display light intensity has been designed for
maximum visibility and product life at the factory.
The use of higher output fluorescent lamps (H.O.
and V.H.O.), will shorten the shelf life of the
product.
9. In the Deli cases, completely cover the product
each night with a clean damp cloth or butcher
paper (never use plastic, as it does not allow
User Information
appearance and significantly shortening product
shelf life.
10. Cold coils remove heat and moisture from the case
and deposit this as frost onto the coil. Thus, a
defrost is required. Our humidity system induces
moisture into the case and helps slow down the
dehydration process. The only other moisture
within the case is that in the product itself. A single
level of meat will dry out faster than a fully loaded
case of 3–4 levels of meat.
IMPORTANT STEPS
1. For temperature settings, please see the Case
Specifications section in this book.
2. Temperature control should be by means of a T-Stat
and Suction Stop Solenoid at each case. Do not use
EPR valves, Liquid Line Solenoids or electronic
control devices of any kind, as these allow
temperature swings causing dehydration and
excessive energy consumption.
3. Product should be worked and rotated on a regular
basis, not to exceed a 4-hour period.
4. At night, turn off case lights and cover the product
with a damp (not wet) cloth similar to cheese cloth
(etc.). This should be washed out in the morning
and kept in a walk-in box during the day—so that it
is cool and moist when covering the product.
5. Discharge air temperature should be approximately
26°F, with between 150-200 FPM air velocity. Do
not display product directly within the air
discharge.
6. Clean Humidity system a minimum of every 90 days
for proper system operation.
CASE CLEANING
Long life and satisfactory performance of any equipment
are dependent upon the care given to it. To insure long
life, proper sanitation and minimum maintenance costs,
the refrigerator should be thoroughly cleaned frequently.
SHUT OFF FAN DURING CLEANING PROCESS. It can
be unplugged within the case, or shut off case at the
source. The interior bottom may be cleaned with any
domestic soap or detergent based cleaners. Sanitizing
solutions will not harm the interior bottom, however,
these solutions should always be used according to the
Hussmann's directions. It is essential to establish and
regulate cleaning procedures. This will minimize bacteria
causing discoloration which leads to degraded product
Soap and hot water are not enough to kill this bacteria. A
12
Advertisement
Table of Contents
