Hussmann RGD Installation And Operation Manual
Upright deli case
Hide thumbs
Also See for RGD:
- Technical data sheet (40 pages) ,
- Installation & operation manual (77 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hussmann RGD
Summary of Contents for Hussmann RGD
- Page 1 Upright Deli Case p/n IGUP-RGD-0106 INSTALLATION & OPERATION GUIDE...
-
Page 2: Table Of Contents
(800) 395-9229 General Instructions THIS BOOKLET CONTAINS INFORMATION ON: RGD A narrow depth multi deck air curtain case designed to display pre-packaged Deli products. It can be placed at the end of gondolas or within a gondola by removing a gondola deck and shelves above from one 4'-0"... -
Page 3: Cut & Plan Views
72” High 24” Wide " Top Electrical 3" Bottom Electrical 9" 9" 1" 1" 12" " 24" RGD83 24 Refrigerated Gondola Display 83” High 24” Wide Refrigeration 3" Bottom Drain 9" Refrigeration CASE FRONT 1" " RGD-GONDOLA Scale = 1/2"... -
Page 4: 30" Depth Series
18" " 30" RGD7230 Refrigerated Gondola Insert Display 72” High 30” Wide 72" ELEC. DROP DRAIN ELEC. REF. DROP DROP RGD83 30 Plan View of 6' case Scale=1/2" IGUP-RGD-0106 18" " " RGD8330 Ref. Gondola Display Scale = 1/2'' 1"... -
Page 5: Installation
Rev.0106 LOCATION The refrigerated merchandisers have been designed for use only in air conditioned stores where temperature and humidity are maintained at or below 75 F and 55% rela- tive humidity. DO NOT allow air conditioning, electric fans, ovens, open doors or windows (etc.) to create air cur- rents around the merchandiser, as this will impair its cor- rect operation. -
Page 6: Ends
Do not install condensate drains in contact with b. Where condensate drains are located in dead air RGD (SELF CONTAINED) The waste outlet and P-trap are the same as the remote except the case condensate drains to a pump assembly mounted to the top of the case into the top of the water evap assembly. -
Page 7: Refrigeration
Rev.0106 REFRIGERANT TYPE The standard refrigerant will be R-22 unless otherwise specified on the customer order. Check the serial plate on the case for information. PIPING The refrigerant line outlets are located under the fixture at the left hand end when viewed from the back. Insulate the suction lines to prevent condensation leakage. -
Page 8: T-Stat Location
A thermostat is located on the top of thje case for temperature control. Set the thermo- stat to cycle in and out as per the Case Specification sec- tion of the guide. Set the timeclock to RGD-SC Electrical BEFORE SERVICING ALWAYS DISCONNECT ELECTRICAL... -
Page 9: Finishing Touches
Finishing Touches If more than one RGD is being installed next to each other, the factory fitted continuous fascia may need to be in- stalled. All fasciae rest on the top of their cases. The self- contained fascia has a hook that needs to be slid through... -
Page 10: Case Specifications
208 ~ 230 19.0 208 ~ 230 13.0 208 ~ 230 19.0 208 ~ 230 13.0 208 ~ 230 19.0 208 ~ 230 13.0 208 ~ 230 19.0 IGUP-RGD-0106 0.33 0.60 3.32 0.66 1.20 3.32 0.66 1.20 5.48 0.99 1.80 7.64 0.33 0.60... -
Page 11: Electrical Schematic
Rev.0106 Electrical Schematic... - Page 12 IGUP-RGD-0106 CASE SCHEMATICS (CONT’D)
- Page 13 Rev.0106 CASE SCHEMATICS (CONT’D)
- Page 14 IGUP-RGD-0106 CASE SCHEMATICS (CONT’D)
- Page 15 Rev.0106 CASE SCHEMATICS (CONT’D)
- Page 16 IGUP-RGD-0106...
- Page 17 Rev.0106...
- Page 18 IGUP-RGD-0106...
- Page 19 Rev.0106...
- Page 20 IGUP-RGD-0106...
- Page 21 Rev.0106...
- Page 22 IGUP-RGD-0106...
- Page 23 Rev.0106...
- Page 24 IGUP-RGD-0106...
- Page 25 Rev.0106...
- Page 26 IGUP-RGD-0106...
- Page 27 Rev.0106...
- Page 28 IGUP-RGD-0106...
- Page 29 Rev.0106...
- Page 30 IGUP-RGD-0106...
-
Page 31: User Information
Hussmann cases were not designed to “heat up” or “cool down” product—but rather to maintain an item’s proper temperature for maximum shelf life. To achieve the pro- tection required always: 1. -
Page 32: Plexiglass & Acrylic Care
If beads appear as it is applied, the coat is too thick and the excess should be removed with another cloth. Allow the coating to dry, then bring to a high gloss with a soft cloth. IGUP-RGD-0106... -
Page 33: Maintenance
Should fans or blades need servicing, always replace fan blades with the raised embossed side of the blade TOWARD THE MOTOR. COPPER COILS The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local Maintenance refrigeration wholesalers. -
Page 34: Appendices
1 inch internal diameter. A test thermometer scaled only in Celsius or dually scaled in Celsius and Fahrenheit shall be accurate to 1 C (1.8 F). Temperature measuring devices that are scaled IGUP-RGD-0106... -
Page 35: Appendix D. - Recommendations To User
Rev.0106 only in Fahrenheit shall be accurate to 2 F. The thermometer should be checked for proper calibration. (It should read 32 F when the stem is immersed in an ice water bath). b) LOCATION – The probe or sensing element of the thermometer should be located in the airstream where the air first enters the display or storage area, and not more than 1 inch away from the surface and in the center of the discharge opening. -
Page 36: Limited Warranty
On Hussmann refrigeration systems, an additional (4) year extended warranty for the motor/compressor assembly is available, but must be purchased prior to shipment to be in effect. Hussmann reserves the right to inspect the job site, installation and reason for failure. -
Page 37: Hussmann ® Chino 13770 Ramona Avenue • Chino, California
Rev.0106 Service Record Last service date: Additional copies of this publication may be obtained by contacting: Hussmann ® Chino 13770 Ramona Avenue • Chino, California 91710 (909) 628-8942 FAX (909) 590-4910 (800) 395-9229 /Chino The MODEL NAME and SERIAL NUMBER is required in order to provide you with the correct parts and information for your particular unit.