Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each merchandiser. Glass Front Models LWG / LWUG HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Low Temperature Wall and Island,...
Page 2
Moving along the honeycomb, repeat this process to remove the honeycomb. Honeycomb Retainer Acrylic Guard Retainer Screw Detail A Figure 1. Remove Honeycomb Figure 2. Remove Honeycomb with Fingers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers...
Page 3
Low Temperature Wall and Island, Glass Front Models Figure 3. Remove Acrylic Guard Figure 4. Install Nut Retainer - LG Case HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. P/N 0391765 Remove the acrylic guard from the front side of the wall case, or...
Low Temperature Wall and Island, Glass Front Models GLASS FRONT CASES LWG / LWGH LWUG / LWUGH 1 In. Foam Tape Gasket HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. LNG / LIG In. Foam Tape Gasket Figure 7. Gasket Diagram P/N 0391765 Apply Gaskets –...
Flat Washer – 6, Lock Washer – 7 and Cap Screw – 8. Tighten until gaskets are compressed. After end assemblies have been tightened, insert Plug Buttons – 9. Detail B Figure 8. Install End Panels HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Page 7
Low Temperature Wall and Island, Glass Front Models Apply Silicone Figure 9. Apply Silicone Top Rail Figure 10. Install Glass Post End Cover HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. Detail C P/N 0391765 Apply a bead of Silicone — 10 where end and case join.
Page 8
Use Screws — 12 to attach Splashguard Channel — 13 to legs of merchandiser. Use Screws — 14 to attach Splashguard — 15 to splashguard channel. Figure 11. Install Splashguard Channel Figure 12. Install Splashguard HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers...
Quantity Note: Nut retainers are factory installed in the left end, and alignment pins are factory installed in the right end of each merchandiser. Solid Front Models HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. Description Nut Retainer (Left end only)
Page 10
Press gently until the top corner clears the retainer. Moving along the honeycomb, repeat this process to remove the honeycomb. Figure 1. Remove Honeycomb Figure 2. Remove Honeycomb with Fingers HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. ® Merchandisers...
Page 11
Low Temperature Wall and Island, Solid Front Models Internal Panel Figure 3. Remove Internal Panel Figure 4. Install Nut Retainer - L Case HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. P/N 0391765 Remove the internal panel from the front side of the wall case, or...
Page 13
Low Temperature Wall and Island, Solid Front Models SOLID FRONT CASES LW / LWU 1 In. Foam Tape Gasket HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. LN / LNM / In. Foam Tape Gasket Figure 7. Gasket Diagram P/N 0391765 Apply Gaskets –...
Page 14
Flat Washer – 6, Lock Washer – 7 and Cap Screw – 8. Tighten until gaskets are compressed. After end assemblies have been tightened, insert Plug Buttons – 9. Detail A Figure 8. Install End Panels HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Page 15
Low Temperature Wall and Island, Solid Front Models Apply Silicone Figure 9. Apply Silicone Figure 10. Install Splashguard Channel HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A. P/N 0391765 Apply a bead of Silicone — 10 where end and case join.
Page 16
® P/N 0391765 Merchandisers Use Screws — 13 to attach Splashguard — 14 to splashguard channel. Figure 11. Install Splashguard HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.