Related Manuals for Humminbird 610
Summary of Contents for Humminbird 610
- Page 1 531440-1_B - HDR610 Manual_Eng.qxd 10/12/2005 11:05 AM Page 1 Humminbird® HDR 610 Installation and Operations Manual 531440-1_B...
-
Page 2: Table Of Contents
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® does require repairs, we offer an exclusive Service Policy - free of charge during the first year after purchase, and available at a reasonable rate after the one-year period. - Page 3 Page 4 HOW SONAR WORKS Sonar technology is based on sound waves. The HDR 610 Digital Depth Gauge uses sonar to determine depth directly below the transducer. Your HDR 610 Digital Depth Gauge consists of two components: the HDR 610 sonar unit and the transducer. The sonar unit contains the transmitter and receiver, as well as the user controls and display.
-
Page 4: Customizing And Assembling The Hdr 610
Before you start installation, we encourage you to read these instructions carefully in order to get the full benefit from your HDR 610 Digital Depth Gauge. You will install your HDR 610 depthsounder first, then your transducer. When you are done with both of these installation tasks, you should perform a final installation test before operating your HDR 610. - Page 5 3. The bezel is keyed to fit only one way onto the front of the HDR 610. There are two opposing sets of tabs on the inside of the bezel: two wide tabs, and two tabs with slots in them.
-
Page 6: Connecting To The Power Supply
2. Install the "U" bracket and wingnut from the rear of the panel, and make sure that the face of the HDR 610 is oriented correctly, so that the top of the unit is at the top of the hole. -
Page 7: Transducer Installation
531440-1_B - HDR610 Manual_Eng.qxd 10/12/2005 TRANSDUCER INSTALLATION If you have a transom mount transducer you can mount it on the transom (preferred), in the hull, or you can purchase the trolling motor adapter and mount it on your trolling motor. If you have a puck transducer then you can ONLY mount it in the hull;... -
Page 8: Mounting The Transducer Assembly To The Transom
If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50' (15 m). For assistance, contact the Customer Resource Center at www.humminbird.com or call 1-800-633-1468 for more information. -
Page 9: Final Testing
Mounting, Puck Transducers Only section instead. In-hull mounting generally produces good results in single- thickness fiberglass-hulled boats. Humminbird® cannot guarantee depth performance when transmitting and receiving through the hull of the boat, since some signal loss occurs. The amount of loss depends on hull construction and thickness, as well as the installation position and process. -
Page 10: Routing The Cable
1. When the boat ignition is turned on, the HDR 610 will perform a self test, and then begin transmitting. It will automatically display the digital depth. -
Page 11: Inside The Hull Mounting, Puck Transducers Only
Inside the hull mounting of the transducer generally produces good results in single thickness fiberglass hulled boats. Humminbird® cannot guarantee depth performance when transmitting and receiving through the hull of the boat, since some signal loss will occur. The amount of loss depends on hull construction and thickness, and the installation. -
Page 12: Routing The Cable
If the cable is too short, extension cables are available to extend the transducer cable up to a total of 50' (15 m). For assistance, contact the Customer Resource Center at www.humminbird.com or call 1-800-633-1468 for more information. 4. Permanently Mounting the Transducer NOTE: Once permanently mounted, you will not be able to make further adjustments to the transducer. -
Page 13: Operating The Hdr 610
As your HDR 610 transducer receives sonar signals, it converts them to a digital depth that is shown on the HDR 610 display. The depth reading is continuously updated as you travel across the water. -
Page 14: Units
531440-1_B - HDR610 Manual_Eng.qxd 10/12/2005 1. While in normal operation mode, press the SET key until the Deep Alarm setting is displayed and the Deep icon is blinking. 2. Use the UP Arrow key to activate the Deep Alarm and also to increase the selected value. Use the DOWN Arrow key to reduce the value. -
Page 15: Hdr 610 Maintenance
HDR 610 MAINTENANCE If your HDR 610 unit comes into contact with salt spray, simply wipe the affected surfaces with a cloth dampened in fresh water. Do not use a chemical glass cleaner on the lens, as chemicals in the solution may cause cracking in the lens. -
Page 16: Hdr 610 Doesn't Power Up
(refer to the Transducer Installation section); • check the transducer cable connection on the back of the HDR 610 and make sure that the cable to the transducer has not been cut or pinched, as even a small abrasion in the cable can affect performance significantly. -
Page 17: Returning Your Unit For Service
We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain. This Service Policy is valid in the United States only. This applies only to Humminbird® products returned to our factory in Eufaula, Alabama. This Service Policy is subject to change without notice. -
Page 18: Contact Humminbird
531440-1_B - HDR610 Manual_Eng.qxd 10/12/2005 CONTACT HUMMINBIRD® Contact the Humminbird® Customer Resource Center in any of the following ways: By Telephone (Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time): 1-800-633-1468 By e-mail (typically we respond to your e-mail within three business days): custserv@johnsonoutdoors.com...