Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ...............................2 Important safeguards ............................3 Installation/ connection............................4 Panel controls ..............................8...
Important safeguards Using the device at temperature below -10º may cause the breakage of the device. BEFORE USING PLEASE HEAT PASSENGER COMPARTMENT RECOMMENDED TEMPERATURE! Read carefully through this manual to familiarize yourself with this high-quality sound system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit. When replacing the fuse, be sure to use one with an identical amperage rating.
Installation/ connection Attention: REMOVE THE TRANSPORT CD STOPPER (2 SCREWS) BEFORE USE. Din front-mount (method 1) After inserting the holder into the dashboard, select the appropriate tab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame and remove it. Insert the levers supplied with the unit to the grooves at both sides.
Page 5
Din rear-mount (method 2) Installation using the screw holes at both sides of the unit. 1. Select a position where the screw holes of the main unit are fitted for aligned, and tighten the screws at 2 positions at each sides. Use either truss screws (5 x 8mm) or flush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket.
Page 6
Attaching the control panel 1. Insert the right side of the control panel into the main unit (pic. 3). Note: the control panel must be attached into the T-Joint. 2. Press the control panel on to the left side of middle of it until a “click”...
Page 7
Electrical connection Caution: Do not interchange the connection of the wiring!!! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit.
Panel controls Front panel 1. PWR button Press PWR button to turn the power on, press again to turn the power off. 2. VOL knob/ SEL button Rotate VOL knob clockwise to increase the volume level; rotate anticlockwise to decrease the volume level. Press SEL button once to enter the Audio select menu.
Page 9
3. IR sensor 4. DIS/REC button Press shortly to display current mode and time. Press and hold for 2 seconds to enter the Record function. 5. MODE button Press to select the mode: TUNER => CD => SD/MMC => USB => AUX.
Page 10
16. PAUSE button Use this button to pause playback. Under the pause status, press it to play. 17. PRESET STATION [1-6] buttons 18. AF/REG button Press it to enter the AF mode. Press and hold for 2 seconds to enter the REG mode. 19.
Page 11
Remote control 1. DIS/REC button Press shortly to display current mode and time. Press and hold for 2 seconds to enter the Record function. 2. MODE button Press to select the mode: TUNER => CD => SD/MMC => USB => AUX.
Page 12
8. TA/TP button Press it to activate the TA function. 9. PTY button Press it to activate the PTY function. 10. AF/REG button Press it to enter the AF mode. Press and hold for 2 seconds to enter the REG mode. buttons Press to go to the previous/ next track.
Page 13
Changing the battery 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach.
Page 14
Back of the front panel Press the OPEN button on the front panel to flip it down. 1. Disc slot; 2. SD CARD socket; 3. EJECT button; 4. Panel status indicator; 5. RESET button. Note: Pressing the RESET button will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down;...
General operation Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press OPEN button on the panel to open the panel and press the RESET button to restore the unit to the original factory settings.
Page 16
Setting other characteristics During FM mode, keep pressing SEL button for 2 seconds to enter another mode. Shortly and repeatedly press the SEL button to select the setting: IN VOL => ADJ => TA VOL => EON => REC => DSP => LOUD => LOC => STEREO.
Page 17
Display operations 1. Press the DIS/ REC button to show the following current tuning information and time in any play mode: CT (Clock/ Time) => PTY => Radio frequency =>PS. 2. Press and hold for 2 seconds to enter the RECORD mode. Setting the time 1.
Digital tuner Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Band selection Press PWR to power on, then press the MODE button to select TUNER. Press BAND once or more to select: FM1, FM2, FM3, MW1, MW2.
Page 19
AS/ PS function (Auto Store/ Preset Scan) Preset scan: press AS/ PS button to scan all preset stations in the memories of the current band and stay on each memory stations for about 5 seconds. The memory location indicator on the LCD will flash during the process.
Page 20
PTY (Program Type) function 1. Press PTY button to activate the PTY function. 2. Press T-UP/ T-DN buttons to search the last time selected PTY program. 3. Press PTY button long time to select PTY program type (turn the knob to select PTY type). 4.
CD/ SD/ MMC/ USB operations Loading a disc 1. Turn the power on. 2. Press the OPEN button on the panel. 3. Insert the disc with the printed side facing upward into the slot. 4. Press EJECT button on the inner side to eject the disc. Inserting the SD/ MMC card/ USB device Insert the MMC/ SD card or USB device into MMC/ SD compartment or USB socket.
Page 23
Scanning forward and backward Press and hold for 2 seconds the T-DN or T-UP buttons to fast the playing in backward or forward direction. Note: During the disc playback when Fast/ Reverse Playback gets to the beginning of the playing another track, it resumes normal playback.
Page 24
Search function In CD/ MMC/ SD/ USB mode, press AS/PS button to enter the Music file search menu. Press again to select the search mode: FILE NUMBER SEARCH => FILE NAME SEARCH => FOLDER SEARCH => exit search mode. Audio CD supports the FILE NUMBER SEARCH only. File number search 1.
File managing Encoding (recording) function Encoding (Recoding) function enables sound source from Tuner, CD, AUX-in to record directly to USB device or SD/MMC card. Recoding at Tuner/ AUX-in mode Press DIS/REC button for more than 2 seconds, the unit asks the location of recording device. Press DIS/REC once to select recording device in the sequence of SD/MMC =>...
Page 26
Recording at MP3 CD mode Press DIS/REC for more than 2 seconds and the unit asks the location of copy device in the following sequence: MMC => USB. Press DIS/REC to select intended location. To exit recording, press DIS/REC more than 2 seconds. To start recording, press the BAND button.
MP3 overview Notes on MP3: MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. The unit can read MP3 files written in the format compliant with ISO 9660. However it does not support the MP3 data written by the method of packet write.
Make sure that when MP3 CD-R or CD-RW is burned that it is formatted as a data disc and NOT as an audio disc. You should not write non-MP3 files or unneeded folders along with MP3 files on the disc otherwise it takes a long time until the unit starts to play MP3 files.
Handling discs Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or dust.
Troubleshooting guide Cause Solution Symptom General The car ignition is not on. If the power supply is properly connected to the car No power The fuse is blown. accessory switch the ignition key to “ACC”. Replace the fuse. Disc Presence of disc inside the player. Remove the disc in the player then put a new Disc cannot be loaded.
Page 31
The radio does not work, The antenna cable is not connected the Insert the antenna cable firmly select a station the radio station signals are too weak. manually. automatic selection does not work.
Specification General Power supply: 11-16 V DC Current consumption: max. 10 A Maximum power output: 50 W x 4 channels Dimensions (L x W x H): 178 x 175 x 50 mm Working temperature range: -10º - +60º FM Stereo Radio Frequency range: 87.5 - 108.0 MHz Usable sensitivity:...
Page 46
RESET ( OPEN. RESET, PWR, V +/- SEL ( : VOLUME ) => BASS ( ) => TRE LE ( ) => BALANCE ( ) => FADER (...
Page 47
SEL, SEL ( : IN VOL => ADJ => TA VOL => EON => REC => DSP => LOUD => LOC => STEREO. IN VOL – – TA VOL : EON ON ( .) => EON OFF ( EON ON ( WMA =>...