Summary of Contents for Neilsen CT1709
- Page 1 13HP GASOLINE HIGH PRESSURE WASHER CT1709 ORIGINAI INSTRUCTION Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM SAVE THESE INSTRUCTIONS FOR REFERENCE...
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description:13HP GASOLINE HIGH PRESSURE WASHER Model: CT1709 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN 60335-2-79:2012 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 3: Specifications
1. SPECIFICATIONS Rated Power: 13HP/9.6Kw, 4 stroke Rated Pressure: 22.0 x 10 Allowable Pressure: 25.0 x 10 Rated Flow: 13.0 L/min No load speed: 3400RPM Allowable Temperature: 0 - 60 Warning:Sound power level emitted by this machinery is 113db during normal operation. - Page 4 extend a suitable distance from the tool user. 7. Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an application it is not designed for.
-
Page 5: Specific Safety Instructions For Pressure Washer Use
16. Prevent unintentional starting. Before plugging any machine in to the power supply, make sure the switch is in the OFF position. If the machine is portable; do not hold the machine near the switch and take care when putting the machine down;... - Page 6 potential hazards and limitations for your unit. • This equipment is designed for specific applications. Do not modify or use for any application other than which it is designed. • Store the pressure washer in a well ventilated area with the fuel tank empty. Fuel Should not be stored near the pressure washer.
- Page 7 defects should be corrected before operation. • Do not touch hot muffler. • Service, operate and refuel under the following conditions: a. Good ventilation. b. Refuel the pressure washer in a well lighted area. c. Avoid fuel spills and never refuel while the pressure washer is operating. d.
-
Page 8: Technical Description
3. TECHNICAL DESCRIPTION 1. Petrol engine. Wheel. 3. Frame. 4. Gun. 5. Lance. Pressure pump. 7. High pressure hose. 8. Nozzle panel. 9. Selection of nozzles. -
Page 9: Unpacking And Checking
4. UNPACKING & CHECKING PACKAGING Carefully remove the machine from the packaging and examine it for any sign of damage that may have happened during shipping. Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the seller and do not attempt to use the machine. -
Page 10: Operating Connections
OPERATING CONNECTIONS High Pressure Hose Attach the high pressure hose to the pressure washer by pulling back the collar on the quick connect coupling on the hose and pushing it over the coupling half on the pressure washer outlet. NOTE: DO NOT use a high pressure hose from another manufacturer. Water Connection Before connecting to unit, run water through the garden hose (not supplied) to flush out any foreign matter. -
Page 11: Chemical Injection
CHEMICAL INJECTION CAUTION! This pressure washer is intended for use only with liquid car wash Detergents, developed specifically for pressure washer and with mild soaps. Only use chemicals compatible with the aluminum and brass parts of the pressure washer. Powdered soaps may clog the injection system. Always use chemicals according to the manufacturer directions.We assumes no responsibility for any damages caused by chemicals injected through this pressure washer. -
Page 12: End Of Operation
a scrub brush. Application Of Wax 1. Immediately after cleaning, apply wax. Place injection tube in container of wax. 2. Apply the wax sparingly in an even layer. Apply to wet surfaces from bottom up for even distribution and to avoid streaking. 3. -
Page 13: Engine Maintenance
in place. Remove the screen and back flush to remove impurities from screen.Replace immediately. ENGINE MAINTENANCE During the winter month,rate atmospheric conditions may develop which will cause an icing condition in the carburetor.If this develops,the engine may run rough,lose power,and may stall.This temporary condition can be overcome by deflecting some of the hot air from the engine over the carburettor area. - Page 14 3. Pour about one teaspoon of engine oil through the spark plug hole，pull the recoil starter slowly until you feel increased pressure which indicates the piston is on its compression stroke and leave it in that position. This closes both the intake and exhaust valves to prevent the inside of the cylinder from rusting.
-
Page 15: Troubleshooting
8. TROUBLE SHOOTING... - Page 16 9. DISPOSAL At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •...
-
Page 17: Exploded View
10. EXPLODED VIEW PUMP... - Page 18 PART PART CODE DESCRIPTION CODE DESCRIPTION Overheat protection 01.10.11.063 Hexagonal bolts 8*30 01.10.11.097 valve 01.10.12.074 Crankshaft oil seal cover 01.10.12.073 1/2 to 1/4 connector 01.10.12.061 oil seal for crankshaft 01.10.11.090 O ring 14*1.8 Pump housing connection Stainless steel hexagon 02.01.041 flange (large) 01.10.12.040 socket screw M8*55...
- Page 19 01.10.07.038 Shaft circlip 01.10.12.025 Mandrel nut Gasoline engine crankshaft 25.4 Pressure regulating 02.01.20.002 Eccentricity 7.0 01.10.12.026 valve retaining ring 01.10.12.006 connecting rod 01.10.12.052 O ring 9*1.8 01.10.12.013 Plunger pin open gasket ring 01.10.12.018 Plunger spray 01.10.11.075 O ring 14*2 01.10.12.062 Plunger oil seal 01.10.11.075 O ring 14*2 01.10.12.011 Pressure ring...
- Page 20 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...