Tuner Operation; Tape Recording; Front-Panel Connections - Harman Kardon DPR 1005 Owner's Manual

• Some source devices, particularly cable set-top
boxes, will switch back and forth between digital and
analog audio outputs, depending on the channel
being watched. To avoid losing sound with this type
of product, it is recommended that you connect
both the digital and analog audio outputs of the
source to the DPR 1005, with the digital audio input
set as the default following the steps shown on
page 21. The DPR will monitor the digital data
stream and when it is interrupted the sound will
mute briefly and possibly display an UNLOCK
message while it switches to the analog audio input.
This switching is not a fault of either the DPR or the
cable box, as it is caused by the use of different
audio technologies on different channels by the
cable company or program supplier.
• Although the DPR 1005 will decode virtually all current
DVD movies, CDs and HDTV sources, it may not be
compatible with future digital sources.
• When a digital source is playing, you may not be
able to select some of the analog surround modes
such as Dolby Pro Logic II, Dolby Pro Logic IIx, Hall,
Theater or Logic 7.
• When a Dolby Digital or DTS source is playing,
it is not possible to make an analog recording using
the Tape Outputs ⁄ and Video 1 or Video 2
Audio Outputs £∞. However, the digital signals
will be passed through to the Digital Audio
Outputs °·J.

Tuner Operation

The DPR 1005's tuner is capable of tuning AM, FM
and FM Stereo broadcast stations. Stations may be
tuned manually, or they may be stored as favorite sta-
tion presets and recalled from a 30-position memory.
Station Selection
1. Press the AM/FM Button on the remote to
34
select the tuner as an input. The tuner may be
selected from the front panel by either pressing the
Input Source Selector 8 until the tuner is active
or by pressing the Tuner Band Selector 6.
2. Press the AM/FM Button 34 or Tuner Band
Selector 6 again to switch between AM and FM
so that the desired frequency band is selected.
3. Press the Tuning Mode Selector 9 l to select
manual or automatic tuning.
When the button is pressed so that AUTO or
AUTO/STEREO appears in the Upper
Display Line ^, each press of the Tuning
Selectors 5w will put the tuner in a scan
mode that seeks the next higher or lower frequency
station with acceptable signal strength. An AUTO
ST TUNED indication will momentarily appear
when the station stops at a stereo FM station, and
an AUTO TUNED indication will momentarily
appear when an AM or monaural FM station is
tuned. Press the Tuning buttons again to scan to
the next station.
When the button is pressed so that MANUAL
or MANUAL/MONO appears in the Upper
Display Line ^, each tap of the Tuning
Selectors 5w will increase or decrease the
frequency by one increment. When the tuner
receives a strong enough signal for adequate
reception, MANUAL TUNED will appear
in the Lower Display Line &.
4. Stations may also be tuned directly in either the
automatic or manual mode. To enter a station's fre-
quency directly, first select the AM or FM band as
desired be pressing the AM/FM Button 6
Next, press the Direct Button i. Within five
seconds of when DIRECT IN scrolls in the
Upper Display Line ^, enter the station fre-
quency by pressing the Numeric Keys k. If you
press an incorrect button while entering a direct fre-
quency, press the Clear Button j to start over.
NOTE: When the FM reception of a station is weak,
audio quality will be increased by switching to Mono
mode by pressing the Tuning Mode Button 9 l
so that MANUAL/MONO appears momentarily
in the Upper Display Line ^ and then goes out.
This will also activate manual tuning mode.
Preset Tuning
Using the remote, up to 30 stations may be stored in
the DPR 1005's memory for easy recall using the
front-panel controls or the remote.
To enter a station into the memory, first tune the sta-
tion using the steps outlined above. Then:
1. Press the Memory Button 39 on the remote;
the station's frequency will flash.
2. Within five seconds, press the Numeric Keys k
corresponding to the memory location where you
wish to store this station's frequency. Once entered,
the preset number will appear in the Upper
Display Line ^.
3. Repeat the process after tuning any additional
stations to be preset.
Recalling Preset Stations
• To manually select a station previously entered in
the preset memory, press the Numeric Keys k
for the desired station's memory location.
OPERATION OPERATION
• To manually scroll through the list of preset stations,
press the Preset Stations Selector Button
7v on the front panel or remote.

Tape Recording

In normal operation, the audio or video source
selected for listening through the DPR 1005 is sent to
the record outputs. This means that any program you
are watching or listening to may be recorded simply
by placing machines connected to the outputs for
Tape Outputs ⁄ or Video 1/Video 2 Outputs
£∞ in the record mode.
When a digital audio recorder is connected to the
Digital Audio Outputs °·, you are able to record
the digital signal using a CD-R, MiniDisc or
other digital recording system.
NOTES:
. • The digital outputs are active only when a digital sig-
34
nal is present, and they do not convert an analog
input to a digital signal, or change the format of the
digital signal. In addition, the digital recorder must
be compatible with the output signal. For example,
the PCM digital input from a CD player may be
recorded on a CD-R or MiniDisc, but Dolby Digital
or DTS signals may not.
• The Front-Panel Video 5 Jacks K may be con-
figured for use as an output, allowing connection to
a recorder, when the steps shown in the section
below are followed.
• Please obey the copyright restrictions on any material
you copy. Unauthorized duplication of copyrighted
materials is prohibited by law.

Front-Panel Connections

In addition to the rear-panel analog outputs, the
DPR 1005 offers Harman Kardon's exclusive
configurable front-panel output-jack feature. For easy
connection of portable devices, you may switch the
front-panel Video 5 Jacks K from an input to an
output by following these steps:
1. Press the OSD Button
MASTER MENU (Figure 1).
2. Press the Set Button q to enter the
IN/OUT SETUP menu (Figure 2).
Navigation Button o so that the
3. Press the
¤
on-screen cursor is next to VIDEO 5.
4. Press the Set Button q and then press the
Navigation Button o so that the word
/
‹ ›
OUT is highlighted.
to view the
OPERATION OPERATION 35 35