Harman Kardon AVR 7300 Owner's Manual page 16

MAIN REMOTE CONTROL FUNCTIONS
Delay Select Button: This button selects
adjustments to the A/V Sync Delay and the individual
channel delays. The first press of the button displays
an A/V SYNC DELAY message in the Lower
Display Line $ and in the on-screen display, which
means that you may change the amount of time that
all channels are delayed together behind the video.
This enables you to compensate for the loss of lip
sync that may be caused by digital video processing
in your display or by television stations. To change
the A/V Sync Delay, press the Set Button q while
the A/V SYNC DELAY message is visible
Navigation Button o
and then use the /
⁄ ¤
to change the setting so that the sound and the
video image are in sync. To change the delay for
an individual output channel, press the
Navigation Button o until the desired channel
name is shown, and then press the Set Button q.
Navigation Buttons o to change
Use the /
⁄ ¤
the delay amount. (See page 28 for more information
on delay options.)
Speaker Select Button: Press this button
to begin the process of configuring the AVR 7300's
bass management system. Then press the
Navigation Button o to select the channel you
wish to set up. Press the Set Button q and
then select another channel to configure. When all
adjustments have been completed, press the Set
Button q twice to exit the settings and return to
normal operation. (See page 26 for more information
on speaker setup.)
Memory Button: Press this button to enter a
radio station to the AVR 7300's preset memory. First,
tune the desired station, and then press this button.
Within five seconds of when you see the station's
frequency flash in the Upper Display Line # and
in the on-screen display, press the numeric keys
for the preset number between 01 and 30 that you
wish to assign to the station. (See page 39 for more
information.)
Stereo Mode Select Button: Press this button
to select a stereo listening mode. When the button is
pressed so that SURROUND OFF appears in
the Lower Display Line , the AVR will operate in
$
a bypass mode with true, fully analog, two-channel
16 MAIN REMOTE CONTROL FUNCTIONS
left/right stereo mode with no surround processing or
bass management, as opposed to other modes where
digital processing is used. When the button is pressed
so that SURROUND OFF appears in the Lower
Display Line $ , and the DSP and SURROUND
OFF Surround Mode Indicators % are lit, you will
enjoy a two-channel presentation of the sound along
with the benefits of bass management. Depending on
whether your system is configured for 5.1 or 6.1/7.1
channels, the next press of the button will cause either
5 CH STEREO or 7 CH STEREO to
appear, and the stereo signal will be routed to all five
(or seven) speakers. (See page 36 for more informa-
tion on stereo playback modes.)
DTS Neo:6 Mode Select Button: Press this
/
⁄ ¤
button as needed to select one of the DTS Neo:6
modes. (See page 36 for the available DTS Neo:6
options.)
Logic 7 Mode Select Button: Press this button
to select from among the available Logic 7 surround
modes. (See page 36 for the available Logic 7 options.)
DTS Digital Mode Select Button: When a
/
⁄ ¤
DTS-encoded digital source is playing, each press of
this button will scroll through the available DTS modes.
The specific choice of modes will vary according to
the type of encoding on the disc and your system's
speaker configuration. When a DTS source is not in
use, this button has no function. (See page 36 for the
available DTS digital options.)
Dolby Mode Select Button: This button is used
to select from the available Dolby Surround modes.
Each press of this button will select one of the Dolby
Pro Logic II or Dolby Pro Logic IIx modes. When a
Dolby Digital-encoded source is in use, Dolby Digital
or Dolby Digital EX mode may also be selected.
(See page 36 for the available Dolby surround
mode options.)
6/8-Channel Input Select: Press this button to
select the device connected to the 8-Channel Direct
Inputs Ü . (See page 34 for more information.)
SPL Select Button: This button activates the
EzSet function to quickly and accurately calibrate the
AVR 7300's output levels. When the button is
pressed, you will then need to select between auto-
matic EzSet operation or using the remote as a manu-
al SPL meter by pressing the Navigation
/
⁄ ¤
Button o until your choice appears in the remote's
LCD display. Press the Set Button q to enter the
setting, and then follow the instructions as displayed
in the LCD display. (For complete information, see
page 29.)
EzSet Microphone Sensor: The microphone
sensor that is used by the EzSet system is behind the
three slots at the top of the remote control. When
using EzSet to calibrate the AVR 7300, be certain that
the slots are not covered. (See page 29 for more
information on using EzSet.)
Lens: The infrared emitters behind the plastic
lens at the top of the remote communicate the remote
codes to the AVR 7300. Be certain that the lens is not
covered when using the remote, and point the lens
toward the AVR for best results. In learning mode, the
remote receives IR codes to be learned through a
sensor behind the lens.
NOTE: DO NOT remove the rubber plug that is supplied
to cover the jack on the upper right side of the remote.
The jack is not active and is reserved for future use.