Table of Contents
Advertisement
System Configuration
After the surround mode setting has been made
with the current input, repeat the setting with all
inputs you will use. The surround mode can also
be changed at any time later, and the AVR's
memory system will keep the settings for the
input selected, until they are changed again.
Configuring the Surround Off
(Stereo) Modes
For superior reproduction of two-channel pro-
gram materials, the AVR offers two Stereo
modes: an analog Stereo-Direct mode that
bypasses the digital signal processing circuitry for
a completely analog signal path that preserves
the purity of the original signal, and a digital
mode that is capable of providing bass manage-
ment for optimal distribution of the low frequen-
cies between smaller speakers and a subwoofer.
Stereo-Direct (Bypass) Mode
When the analog Stereo-Direct mode is selected
by pressing the Stereo Mode Selector
until
appears in the Main
SURROUND OFF
Information Display
and the Surround
Mode Indicator
for Surround Off is lit, the
AVR will pass the analog source material directly
through to the front left and right speakers,
bypassing the digital processing circuitry.
In this mode, the front left and right speakers will
automatically be configured as
LARGE
not possible to configure these speakers as
.
SMALL
When the AVR is in the Stereo Bypass mode you
may still configure the subwoofer output so that
it is either turned off, with a full-range signal
going to the front left/right speakers, or you may
configure it so that the subwoofer feed is activat-
ed. The factory default setting is to have the sub-
woofer turned off for this mode, but you may
change that setting by following these steps:
1. Press the Speaker Button
2. Press the Set Button
to activate the con-
figuration menu.
3. Press the
K
/
L
Buttons
on the remote
to select the desired option.
SUB NONE
off the feed to the subwoofer, while
turns it on.
<L+R>
4. When the desired setting has been entered,
press the Set Button
to return to normal
operation.
18 SYSTEM CONFIGURATION
Stereo-Digital Mode
When the Stereo-Direct (Bypass) mode is in use a
full range signal is always sent to the front
left/right speakers. By its nature, that option does
not pass the signal through the AVR's digital sig-
nal processing, creating the requirement for full-
range speakers. If your front speakers are band-
width limited, "satellite"speakers, we recom-
mend that you do NOT use the Bypass mode, but
rather use the
DSP SURROUND OFF
for stereo listening.
To listen to programs in the two-channel stereo
mode while taking advantage of the bass man-
agement system, press the Stereo Mode
Selector
until
appears in the Main Information Display
and the DSP and
Mode Indicators
the
SURR. OFF
Indicators
(Bypass) mode.
When this mode is in use, the front left/right
speakers and subwoofer may be configured to
meet the requirements of your specific speakers
using the steps shown in the Speaker Setup sec-
tion on page 16.
; it is
.
turns
SUB
mode
SURROUND OFF
Surround
SURR. OFF
both light up. When only
Surround Mode
is lit you are in the Stereo-Direct
Delay Settings
Only for the Dolby or DTS modes, you will need
to adjust the delay time setting. Note that the
delay time is not adjustable for any other modes.
Due to the different distances between the
listening position for the front channel speakers
and the surround speakers, the amount of time it
takes for sound to reach your ears from the front
or surround speakers is different. You may com-
pensate for this difference through the use of the
delay settings to adjust the timing for the specific
speaker placement and acoustic conditions in
your listening room or home theater.
The factory setting (see Surround Mode Chart
page 22) is appropriate for most rooms, but
some installations create an uncommon distance
between the front and surround speakers that
may cause the arrival of front channel sounds to
become disconnected from surround channel
sounds.
To resynchronize the front, center and surround
channels, follow these steps:
1. Measure the distance from the listening/
viewing position to the front speakers in
meters.
2. Measure the distance from the listening/
viewing position to the surround speakers.
3. Press the Delay Button
.
4. When
appears in the
FRONT DELAY
Main Information Display
press the Set
Button
.
5. Press the
K
/
L
Buttons
on the remote
to enter the distance from the front left/right
speakers to your listening position. Press the Set
Button
when this is complete.
6. Press the
K
/
L
Buttons
on the remote
so that
appears in the
CENTER DELAY
Main Information Display
and press the
Set Button
.
7. Press the the
K
/
L
Buttons
remote to enter the distance from the center
speaker your listening position. Press the Set
Button
when this is complete.
on the
Hide quick links:
Advertisement
Table of Contents
