Table of Contents
Advertisement
Available languages
Available languages
Removing the Blade
1. Unplug the saw.
2. Raise the arm to the upper position and raise the lower guard
3. Loosen, but do not remove guard bracket screw
enough to access the blade screw. Lower guard will remain raised due to the position of the
guard bracket screw.
4. Depress the spindle lock button
24
while carefully rotating the saw blade by hand until the
lock engages.
5. Keeping the button depressed, use the other hand and the blade wrench
loosen the blade screw
23
. (Turn clockwise, left-hand threads.)
Fig. C
16
Fig. D
6. Remove the blade screw
23
, outer blade clamp
clamp
27
, and if used, the 1" (25,4 mm) blade adapter, may be left on the spindle.
NoTE: For blades with a blade hole of 5/8" (15,88 mm), the 1" (25,4 mm) blade adapter is
not used.
Fig. E
25
23
Installing a Blade
1. Unplug the saw.
2. With the arm raised, the lower guard held open and the guard bracket raised, place the blade
on the spindle, onto the blade adapter [if using a blade with a 1" (25,4 mm) diameter blade
hole] and against the inner blade clamp with the teeth at the bottom of the blade pointing
toward the back of the saw.
3. Assemble the outer blade clamp
27
onto the spindle.
4. Install the blade screw
23
and, engaging the spindle lock, tighten the screw firmly with
wrench provided. (Turn counterclockwise, left-hand threads.)
5. Return the guard bracket to its original position and firmly tighten the guard bracket
screw
36
to hold bracket in place.
WARNING:
•
The guard bracket must be returned to its original position and the screw
tightened before activating the saw.
•
Failure to do so may allow the guard to contact the spinning saw blade resulting
in damage to the saw and severe personal injury.
4
as far as possible.
36
until the bracket can be raised far
16
provided to
36
23
24
25
, and blade
26
. The inner blade
26
27
Miter Scale Adjustment (Fig. A, F)
Place a square against the saw's fence and blade. (Do not touch the tips of the blade teeth with
the square. To do so will cause an inaccurate measurement.) Unlock miter lock knob
swing the miter arm until the miter detent locks it at the 0˚ miter position. Do not lock miter lock
knob. If the saw blade is not exactly perpendicular to the base fence
scale screws
8
that hold the miter scale
7
left or right until the blade is perpendicular to the fence, as measured with the square. Retighten
the three screws. Pay no attention to the reading of the miter pointer at this point.
Fig. F
Miter Pointer Adjustment (Fig. A, F, G)
Unlock miter lock knob
5
and squeeze the miter detent latch
the zero position. Unlock the miter lock knob to allow the miter detent to snap into place as
you rotate the miter arm toward zero. Observe the pointer
viewing opening shown in Figure H. If the pointer does not indicate exactly zero, loosen the
pointer screw, adjust the pointer to 0˚ and retighten.
Fig. G
7
Bevel Square to Table (Fig. A, H)
To align the blade square to the rotary table, lock the arm in the down position. Place a square
against the blade taking care to not have the square on top of a tooth. Loosen the bevel lock
knob
11
and ensure the arm is firmly against the 0° bevel stop. Move the 0° bevel stop adjusting
screw
19
as necessary so that the blade is at 0° bevel to the table. Ensure the bevel override
levers are pushed inward to obtain an accurate adjustment.
Fig. H
Bevel Pointer (Fig. I)
If the bevel pointer
29
does not indicate zero, loosen the screw
move the pointer as necessary. Do not remove the steel plate in front of the bevel pointer. This
plate prevents wood resin from accumulating on the bevel scale during use.
5
18
, loosen the three miter
to the base and move the scale/miter arm assembly
7
5
6
to move the miter arm to
28
and miter scale
7
through the
28
30
that holds it in place and
ENGlIsH
and
31
Advertisement
Table of Contents
