Summary of Contents for Pentair Pool Products Compool
Page 1
® Compool to EasyTouch ® Pool and Spa Control System Upgrade Upgrade MODES OF OPERATION Auto: Indoor control panel and other remote devices operate system. Service buttons on this panel operate system. Other remote devices are disabled. Time Out: Service buttons on this panel operate equipment for three hours, then settings return to Auto mode.
Page 2
“Single Body” system Configuring Compool/EasyTouch as a SINGLE BODY SYSTEM The Compool EasyTouch Upgrade circuit board is factory configured and ready to operate as a SHARED EQUIPMENT system (Jumper J25 = ON). To change the Compool EasyTouch Upgrade board to operate a SINGLE BODY system, first remove Jumper 25 (place the jumper on one of the pins) and erase the EEPROM (see page 49).
Technical Support ............................v How to Change the system to a SINGEL BODY system ................v Section 1 - Compool to EasyTouch Pool and Spa Control System Upgrade Overview ......1 Compool® EasyTouch® Pool and Spa Control System Upgrade Overview ............ 1 Compool upgrade systems ........................
Page 4
EasyTouch Error Messages .......................... 56 Self Test Error Codes ............................ 56 Error Code Table ............................56 Maximum Programs Exceeded ........................57 IntelliChlor Error Messages ........................... 57 System Problem Diagnosis ........................... 58 Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 5
Compool/EasyTouch Upgrade Models (Single Body Systems) ..............66 Compool/EasyTouch Upgrade Models (Shared Equipment Systems) ............67 Installing Compool/EasyTouch Upgrade Control Panel (with or without Transformer Kit) ......... 68 Compool Power Center (without sub-panel) ....................68 Compool Load Center (with breaker sub-panel) ....................72 Installing the Compool/EasyTouch Upgrade Control Panel (Compool Load Center with sub-panel) ......................
Page 6
Control System is intended to control heaters with built-in high limit circuits ONLY. Failure to do so may cause property damage or personal injury. Do not use this product to control an automatic pool cover. Swimmers may become entrapped underneath the cover. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 7
7. Electrical rating: 120/240 VAC 150 AMP Single Phase (3 wire). 8. The input line to the control panel should be protected by a 240 VAC CIRCUIT BREAKER rated at NO MORE then 150 Amperes maximum. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
• Compool To EasyTouch Upgrade Kit (P/N 521107) - For upgrading CP3xxx systems • Compool To EasyTouch Upgrade Kit with Transformer (P/N 521247) - For upgrading Cp100, Cp1000, Cp2000 system. • Temperature sensor with 20 foot cable, o-ring and hose clamp (P/N 520272) - Uses for the water temperature sensor •...
EasyTouch Pool and Spa Control System Upgrade Overview Welcome to the Compool EasyTouch upgrade Pool and Spa Control system − The next generation in automatic control systems. Your Compool EasyTouch upgrade system opens up a wide range of automation features. Your EasyTouch eight auxiliary system allows you to automatically control all of your spa and pool daily operations.
(Water, Air and • IC20 P/N 520554/520556 Solar optional) • IC40 P/N 520555/520556 Electric Heater - • CIC60 P/N 521105 Connects to plug J19 on (see page 26) motherboard Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Use the Left button to scroll through sub-menu selections, setting and values. While editing settings, press and hold the Left button to fast reverse through settings and values. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 12
Use this mode to service pool equipment and to operate equipment manually. Same functionality as “Service” mode, except that the system will automatically return to Timeout: normal operation (Auto) after three hours. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 13
These auxiliary circuits are assigned in the “Circuit Function” menu, see page 39 for details. There are seven auxiliary circuits (AUX 1- 7) on Compool/EasyTouch outdoor control panel. The Solar button can also be used for an “extra” auxiliary circuit if the Solar circuit is not being for solar equipment.
(see “Man Heat” on page 48). The Spa Mode will automatically turn off after 24 hours. For iS10 setup and configuration information, see page 45. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
(12 hour time-out) Down arrow button can also be used for an “extra” auxiliary POWER ON circuit if solar equipment is not being used EasyTouch wireless control panel - (P/N 520547) Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Compool/EasyTouch Upgrade Outdoor Control Panel Operating Modes The Compool/EasyTouch system can run in automatic mode or manual mode. Use the “Mode” button to switch the system from “Auto” mode (normal operating mode) to “Service” for manual operation and service purposes.
Press the Menu button to save the settings and to return to the Heat menu or press Heat: Heater the button again to return to the main screen. Note: Select “ POOL Temp/Src ” to adjust the pool temperature. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Schedules menu options. Press the Menu button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Schedules menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Schedules menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Setting up Compool/EasyTouch Upgrade System Setting up the Compool/EasyTouch Upgrade System for the First Time Use the following steps to setup up the Compool EasyTouch Upgrade system for the first time. 1. Set the system date and time (page 31) Set the current date and time.
FEATURE 1 - 8 AUX EXTRA: AUXILIARY OUTPUT (USE DOWN ARROW BUTTON TO SWITCH ON/OFF). ONLY AVAILABLE IF AUX EXTRA SOLAR PLUG (J17) IF NOT BEING USED FOR SOLAR EQUIPMENT. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 23
CIR NAMES [ON/OFF] VIEW DEFAULT CIRCUIT NAMES BEFORE MODIFICATION. RESET SYSTEM (REINITIALIZE INDOOR CONTROL PANEL - USE RIGHT BUTTON) FLASH UPDATE (USED FOR FIRMWARE UPDATES VIA PC - PRESS MENU TO ABORT) Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
: Displays the actual outside ambient air temperature (70° F) as recorded by the air sensor located near the EasyTouch load center. : The current system day and time (AM/PM). See the “Clock” menu to set the system day and DAY and TIME time (page 31). Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
When finished, press the Menu button twice to return to the main screen. FEATURE 2 [OFF] FEATURE 3 [OFF] FEATURE 4 [OFF] FEATURE 5 [ON] FEATURE 6 [OFF] FEATURE 7 [OFF] FEATURE 8 [OFF] Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Smart Start (SS: Yes/No) - Select Smart Start in the Schedules menu (see page 27). The Smart Start feature automatically starts changing colors when the lights are programmed to switch on. Smart Start is used when Color Swim and IntelliBrite show modes are being used. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Note: To use the “Color Swim” or “Color Set” feature, select IntelliBrite, SAM, SAL, Photon Generator or Color Wheel. Select “MagicStream” for MagicStream laminars. Press the Menu button three times to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
(6) seconds followed by the selection. If the light was previously on, after selecting the Color Swim feature, the previously selected color will momentarily illuminate, no illumination will occur for approximately six (6) seconds followed by the selection. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
MagicStream laminar circuits. Press the control panel auxiliary button (AuxX) assigned to a light circuit will also switch a light on or off. Sync Select Sync from the “Lights” screen to synchronize colors for all IntelliBrite, SAm, SAL and FIBERworks color changing lights. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
COLOR WHEEL for the circuit controlling the color wheel it self. The circuit light “functions” are: Light, SAM, SAL, Photon Generator, Color Wheel, and IntelliBrite, see page 40 for a more information. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
CLEANER. For a complete list of preset circuit functions, see “Preset Circuit Functions” on page 40. Right button/ Up Button: Turn “Freeze” protection ON. Press the Menu button three times to return to the main screen. Continue on next page... Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
(indicating that the MagicStream feature has been activated) then returns to the Reset Change Mode MagicStream feature menu. Press the Menu button three times to return to the main screen. Change Mode Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Note: For an EasyTouch single body system, “Pool” and “Spa” modes are Lo- Temp (Pool) and Hi-Temp (Spa) temperature controls. For more information, see “Hi-Temp/Lo-Temp Controls for Single Body Systems,” on page 37. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Right button: Use this button activate Delay Cancel for one time only. “Delay Heat Cancelled” is displayed after pressing the Right button. Delay Cancel Press the Menu button to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
New: press the Right button to create a new program. Delete: Select the program and press the Right button to delete it. Mode: Delete None: Press the Right button to exit the “Mode” selections without modifying the program. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Schedules menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Schedules menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Schedules menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
When finished setting up the circuits, press the Menu button to save the settings and the “Settings” menu to return to the Settings menu options. Press the button two times to return to the (page 46). main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
The display will inform the user when this is engaged and when it is finished during the priming cycle at each start up cycle. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 42
GPM: 73 1927 RPM 1980 W Filter: 7 Status: NORMAL Status screen: Displays current operating information: GPM, RPM, Filter minutes, and pump communication status. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
When the filter pump is switched on again using the Filter (F) button, the Super Chlorine process will resume for the duration of time left. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
MENU ▼ SETTINGS ▼ THERMALFLO STATUS Right button: Access the “Status” menu. Settings Status Press the Menu button to return to the main screen. Status [ OP NORMAL <MENU> = EXIT Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Valves (V) button or the Spa (Hi-Temp) and Pool (Lo-Temp) button on the optional Indoor control Panel. Change the circuit name so that the display shows the correct HI-TEMP POOL LO-TEMP temperature controls for your single body system. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
The Solar button is used to switch on and off the extra auxiliary circuit. To access the Solar menu: Getting There MENU ▼ SETTINGS ▼ Solar Solar Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save and to return to the Settings menu options. Press the Menu button again to return to the main menu or press again to go to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu options. Press the button twice to return to the main screen. iS10 button assignments Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu Pump Number: 1 options. Press the button twice to return to the main screen. Step GPM: 001 Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to save the settings and to return to the Settings menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Solar: 90°F and to return to the Settings menu options. Press the button again to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button three times to save the settings and to return to the main screen. Note: If the password feature is enabled, the current four digit password can be viewed from the EasyTouch outdoor control panel in the “Set Password” setting. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
EasyTouch wireless control panel, refer to the EasyTouch Wireless Control Panel User’s Guide (P/N 520688). Address Wireless Sending Address.. Press the Menu button to save the settings and to return to the Settings menu selections. <MENU> Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to return to the Settings menu options. Press the button again UOC: 1.02 to return to the main menu options or press again to return to the main screen. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to return to the Settings menu options. Press the button again UART Test <=Link Closed to return to the main menu options or press again to return to the main screen. >=Link Open Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Press the Menu button to return to the Settings menu options. Press the button again Solar Temperature to return to the main menu options or press again to return to the main screen. 85° F Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
(PC) in order to update the firmware. Press the Menu button to exit the flash mode. Getting There MENU ▼ DIAGNOSTICS ▼ FLASH UPDATE Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
“Solar” as the heat source (Settings Menu: Heat > Solar). Note: Do not set solar as a heat pump. Then the heating method must be selected for each body of water. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
LEDs, and the LCD backlight on the control panel. The following lists the control panel self test error codes. Error Code Table g i l c t i Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
2. Write down what each button switches on, including the number of the circuit. You need this information when you set up the Indoor Control Panel. 3. Label the circuit buttons on the outdoor control panel and the EasyTouch Indoor Control Panel. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Menu is button is pressed to stop the process. Note: To readdress the EasyTouch wireless device, repeat steps 2 through 7 on the wireless device to restart the address process. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
EasyTouch COM port pins YELLOW and GREEN respectively. Do not use pin 1 or pin 4 on the AutoSet board or the EasyTouch motherboard. These pins are not used. Wiring Description Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 72
Blank Page Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
This section describes how to install the Compool/EasyTouch control panel upgrade kit into a Compool load center or power center. For Compool CP3xxx models complete upgrade list, see page 66 and 67. Compool models TimeMaster, CP/LX100, CP1000, CP2000, CP3000 can also be upgraded to an EasyTouch system.
Compool/EasyTouch Upgrade Models The following tables list detailed upgrade information for Compool CP3xxx models. Compool TimeMaster, CP/LX100, CP1000, CP2000, CP3000 can also be upgraded to an EasyTouch system. Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
The following procedure describes how to install the Compool/EasyTouch upgrade control panel (with or without the transformer kit) in a Compool power center (without breaker sub-panel). For Compool/EasyTouch upgrade control panel (with or without the transformer kit) in a Compool load center (with breaker sub-panel), see page 70.
Page 77
Drain VALVES Control panel lower AUX 2 AUX 3 hinge AUX 4 HEATER SOLAR AUX 5 Reset AUX 6 AUX 7 Compool Power Center upgraded with Compool/EasyTouch Control Panel Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 78
Removal/Replacement of Compool Power Center Transformer Assembly: Switch the main AC power OFF to the Compool power center For Compool CP2000 and older systems remove the existing Compool transformer and replace it with the transformer in the Compool/EasyTouch Upgrade with Transformer Kit (P/N 521247).
Page 79
To install the Compool/EasyTouch Upgrade Transformer Assembly: Switch the main AC power OFF to the Compool power center 1. Mount the new transformer assembly above the low voltage compartment of the power center. Route the three (3) wires through the bushing in the high voltage barrier. See illustration on page 72.
To upgrade the Compool/EasyTouch control panel in a Compool load center (with breaker sub-panel), requires temporary removal of the existing transformer to allow the removal of the Compool control panel from the load center and the installation of the Compool/EasyTouch control panel.
Page 81
(TimeMaster) Removal of Compool transformer assembly: 5. For Compool CP2000 and older systems remove the existing Compool transformer and replace it with the Compool/EasyTouch Upgrade Transformer (P/N 521247). a) Remove the three (3) screws securing the service panel to expose the high voltage compartment in the right side of the load center.
Installing the Compool/EasyTouch Upgrade Transformer in a Compool Load Center (with sub- panel) For Compool CP2000 and older systems the existing transformer is removed and replaced with the transformer included with the Compool/EasyTouch Upgrade with Transformer Kit (P/N 521247). Otherwise, CP3xxx systems require P/N 521107.
Page 83
Switch the main AC power OFF to the Compool load center To install the Compool/EasyTouch Upgrade Transformer Assembly: 1. Mount the new transformer assembly above the low voltage compartment of the load center. Route the three (3) wires through the bushing in the high voltage barrier. See illustration on page 72.
RJ12 Adapter for Compool /EasyTouch ® ® Indoor Control Panel or iS10 for Cp3800 family to CONTROL PANEL or iS10 Compool/EasyTouch Upgrade Circuit board Wiring Diagram Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
SELECT 4 CIRCUITS to C O N TR O L PA N E L to SP A - S I DE R EMO T E Compool 3810 Circuit board Wiring Diagram Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...
Page 86
NOTES Compool/EasyTouch Pool and Spa Control System Upgrade Installation and User’s Guide...