Damaged air conditioners are not to be put into operation. In case of doubt, consult your supplier. Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User's Guide.
Always remember to unplug the air conditioner before openning inlet grill. Never unplug your air conditioner by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. All electrical repairs must be carried out by qualified electricians.
Page 4
9.Young children should be supervised ensure that they do not play with the appliance. 10.The appliance must be installed on strong enough supporter. 11 .The wiring diagram is attached inside the machine. Air Conditioner Maximum: D.B / W.B Minimum: D.B / W.B Maximum: D.B...
(adjust left and right air flow) Outdoor unit OUTLET INLET Air Conditioner POWER TIMER HEALTH (adjust up and down air flow. Don't adjust it manually) HSU-09CU13 CONNECTING PIPING AND ELECTRICAL WIRING DRAIN HOSE Edition:2006/1/18 Air Purifying Filter (inside) Air filter(inside) display board Vertical flap...
Page 6
Used to select up or down air sending direction. 10. ON/OFF button Used for unit start and stop. NOTE: The following functions and related displays are not available: 20 Air Conditioner POWER TIMER HEALTH 11. TIMER ON display 12. FAN SPEED display 13.
Page 7
If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out, just need to press reset key. Air Conditioner Edition:2006/1/18 HEALTH POWER/SOFT...
BRIEF INTRODUCTION TO HEALTH ANION FUCTION POWER/SOFT The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room.
Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5.Unit stop Press ON/OFF button, the unit stops.
Press FAN button. For each press, fan speed changes as Remote controller: Air conditioner is running under displayed fan speed. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. Press ON/OFF button, the unit stops.
4.Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp.setting+2 C,unit will run intermittently at LOW speed regardless of FAN setting.
Operation Fan Operation Remote controller POWER/SOFT Air Conditioner 1. Unit start Press ON/OFF on the remote controller, unit starts. 2.Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL Then Select FAN operation 3.Fan speed selection...
AUTO: Pos.1 remote controller: The vertical flap will swing according to the above positions Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. Air Conditioner Vertical flap Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6...
The unit will run for further 6 hours then stops. Temp. is higher than temp. setting so that room temperature won't be too Iow for your sleep. Remote Controller POWER/SOFT Air Conditioner SLEEP operation starts SLEEP operation stops Approx.6hrs Rises 1...
Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if time setting is the same as previous one. Air Conditioner Operation mode will be displayed on LCD. Press TIMER button to change TIMER mode. Every...
Page 16
Operation Timer On-Off Operation Remote Controller POWER/SOFT Air Conditioner Set clock correctly before starting TIMER operation. 1. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. 2. Timer mode selection Press TIMER button to change TIMER mode. Every time...
Press POWER/SOFT button again ,POWER/SOFT disappears. Hints: During POWER operation, in rapid HEAT or COOL mode, the room will show inhomogeneous temperature distribution. Long period SOFT operation will cause effect of not too cool or not too warm. Air Conditioner BLANK SOFT POWER BLANK POWER...
3.In cooling, it is better to select the mode. 4.In cooling and dry, using the air conditioner for a long time under the high air humidity, a phenomenon falling drips of water occurs at the outlet grille . 5.Select the appropriate fan direction according to the actual...
Press the emergency operation switch once more, or manipulate through the remote controller; the "Pi" sound, the emergency or test operation is terminated. When the remote controller is manipulated, it gets the system back to the normal operation mode. Air Conditioner Timer Air flow mode...