Mhl; Avnavigator - Pioneer sc-lx87 Operating Manual

13
Symptoms Remedies
Synchronized operation not possible Check the HDMI connections.
using Control with HDMI function.
The cable may be damaged.
Select ON for the Control Mode with HDMI setting (see
Turn the TV's power on before turning on this receiver's power.
Set the TV side Control with HDMI setting to on (see TV's operating instructions).
Connect the TV to the HDMI OUT 1 terminal and set the HDMI output to OUT 1. Then
turn on first the TV's power, then this receiver's power.
When HDZONE is set to ON, the This is due to the HDMI connection specifications; it is not a malfunction. When play-
video resolution and number of ing the same input in the main zone and HDZONE, video and audio signals that can be
audio channels for the main zone output in common for all the devices connected to the HDMI OUT 1, HDMI OUT 2 and
side changes. HDMI OUT 3 (HDZONE) terminals are set.
HDZONE cannot be turned on. Set Output Setting at MAIN/HDZONE to HDZONE
When the input source for the main This is because the HDMI devices need to recognize each other again. This is not a
or HDZONE is switched or when malfunction. If the picture is disturbed or not displayed, turn off the power of the devices
the power of the respective zones is in all the zones, then try again. Also try temporarily turning the Network Standby and
turned on and off, the audio or video Standby Through settings OFF.
of the HDMI output terminal that is
not being operated is sometimes
interrupted.
Such menus as the HOME MENU as Press HDMI OUT and switch the HDMI OUT 1/2 setting.
well as the on-screen display are not
displayed for HDMI OUT 1 or HDMI
OUT 2.

MHL

Symptoms Remedies
When playing an MHL-compat- The MHL device will not operate unless power is being supplied from this receiver. When
ible device connected to the this receiver is in the Standby Through mode, power cannot be supplied due to reduced
HDMI 5/MHL terminal, the Standby power consumption. Because of this, the MHL device will not operate. This is not a mal-
Through function does not work and function.
the power turns off.
MHL-compatible device cannot be Press MHL to set the remote control to the MHL control mode.
operated with the remote control.

AVNavigator

Symptoms
AVNavigator cannot be
HDMI Setup on page 71).
installed.
The menu is not displayed
even when the included
CD-ROM is inserted into the
(page 105).
computer's drive.
AVNavigator does not inter-
act well with the receiver.
When the Wiring Navi,
Operation Guide,
Interactive Manual or
Glossary is launched, a
warning about security
protection appears on the
browser.
Software updating does not
operate well.
115
Causes Remedies
An error message may appear Restart the computer and start installing with no other
if there are not enough system applications running.
resources available.
Installation of AVNavigator may fail Try the following (in given order):
because of incompatibilities with 1. If other applications are running on the computer, quit
other applications. those applications before installing.
2. If the problem persists, restart the computer and install
with no other applications running.
Depending on the computer's set- Using Explorer, etc., double-click "MAIN_MENU.exe" in the
tings and environment, the menu CD-ROM to execute it. A caution regarding security may
may not be displayed automatically. be displayed, but there is no security problem, so continue
the operation.
You are using a Macintosh com- The provided CD-ROM includes the Windows version of
puter. AVNavigator. The Mac OS version of AVNavigator can be
downloaded from the Pioneer website
The receiver's power is not turned Turn the receiver's power on. (Wait about 60 seconds after
on. the power turns on for network functions to start.)
After this, press Detection in AVNavigator to redetect the
receiver.
To turn this unit's power on and off from the Interactive
Manual, set Network Standby at HOME MENU d
System Setup d Network Setup to ON.
The receiver or computer is not con- Connect a LAN cable to the receiver or computer
nected to the LAN. After this, press Detection in AVNavigator to redetect the
receiver.
The router's power is off. Turn the router's power on.
After this, press Detection in AVNavigator to redetect the
receiver.
AVNavigator's network settings are If your router does not support DHCP or UPnP, the receiv-
not correct. er's IP address must be set in AVNavigator. First set the
IP address on the receiver, then set the same address in

AVNavigator

(page
After this, press Detection in AVNavigator to redetect the
receiver.
Network connections could be Check the computer's network settings, security settings,
restricted due to the computer's net- etc.
work settings, security settings, etc. After this, press Detection in AVNavigator to redetect the
receiver.
This is because of the browser's This is not a problem. Perform the operation to authorize
security function. the blocked contents.
There may be a problem with your Contact your contracted provider.
Internet Service Provider's network.
FAQ
(page 10).
(page 39).
102).