Operation - Husqvarna LC 247 Operator's Manual

To assemble the handle
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product.(Fig. 24 )
3. Set the handle height in one of the 2 available
positions.
4. Move the knobs up in the direction of the handle until
they stop and you hear a click.(Fig. 25 )
5. Tighten the knobs fully.
To set the product in transport position
1. Loosen the lower knobs.
2. Move the knobs to the lower end of the grooves on
the left and the right side of the product.(Fig. 26 )
3. Fold the handle forward.(Fig. 27 )
To set the product in operation position
1. Fold the handle to upright position.(Fig. 28 )
2. Move the knobs up in the direction of the handle until
they stop and you hear a click.(Fig. 29 )
3. Tighten the knobs fully.
To assemble the grass catcher
1. Attach the grass catcher frame to the grass bag with
the rigid part of the bag on the bottom. Keep the
handle of the frame on top of the grass bag.(Fig. 30 )
2. Attach the bottom section of the grass catcher frame
in the groove on the bottom of the grass catcher.
Introduction
WARNING: Before you operate the product,
you must read and understand the safety
chapter.
Before you operate the product
1. Read the operator's manual carefully and make sure
that you understand the instructions.
2. Examine the cutting equipment to make sure that it
is correctly attached and adjusted. See
the cutting equipment on page 13 .
3. Fill the fuel tank. See
4. Fill the oil tank and do a check of the oil level. See
To do a check of the oil level on page 14 .
To fill fuel
If available, use low-emission/alkylate gasoline. If low-
emission/alkylate gasoline is not available, use good
quality unleaded gasoline or leaded gasoline with octane
number not less than 90.
808 - 002 - 19.06.2018
To examine
To fill fuel on page 11 .
3. Attach the grass bag to the grass catcher frame with
the clips.(Fig. 31 )
4. Lift the rear cover.
5. Attach the grass catcher to the top edge of the
chassis.
6. Put the lower part of the grass catcher into the grass
discharge channel.(Fig. 32 )
To assemble the mulch plug
(accessory)
1. Lift up the rear cover and remove the grass catcher.
2. Put the mulch plug into the discharge channel.(Fig.
33 )
3. Replace the blade with the mulch blade that is
supplied in the mulch kit. Refer to
blade on page 13 .
To cut grass without a grass catcher or
mulch plug attached
• Lift up the rear cover and remove the grass catcher.
• If a mulch plug and a mulch blade are attached,
remove them.
• Close the rear cover before you operate the product.
When you operate the product, the cut grass discharges
below the rear cover.

Operation

CAUTION: Do not use gasoline with an
octane number less than 90 RON (87 AKI).
This can cause damage to the product.
1. Open the fuel tank cap slowly to release the
pressure.
2. Fill slowly with a fuel can. If you spill fuel, remove it
with a cloth and let remaining fuel dry off.
3. Clean the area around the fuel tank cap.
4. Tighten the fuel tank cap fully. If the fuel tank cap is
not tightened, there is a risk of fire.
5. Move the product a minimum of 3 m (10 ft) from the
position where you filled the tank before a start.
To set the cutting height
The cutting height can be adjusted in 6 levels.
1. Move the cutting height lever rearward to decrease
the cutting height.
2. Move the cutting height lever forward to increase the
cutting height.(Fig. 34 )
To replace the
11