2 SPECIFIC SERVICE INSTRUCTIONS ..................................................................................................................... 1-4
SERVICE MANUAL FLAT COLOR TELEVISION AV-29VT11 AV-29VT31 AV-29VT11 BASIC CHASSIS POWER POWER MUTING MUTING COLOR CINEMA COLOR CINEMA SYSTEM BASS SURROUND SYSTEM SURROUND DISPLAY SENSOR DISPLAY SENSOR MENU MENU CLOSED CLOSED CAPTION CAPTION TV/VIDEO TV/VIDEO TIMER TIMER PICTURE PICTURE MODE MODE CHANNEL CHANNEL...
Page 2
SPECIFICATION Contents Items AV-29VT11/P AV-29VT31/P AV-29VT11/T Dimentions (W x H x D) 81.2cm x 58.4cm x 52.1cm Mass 43.5kg 43.5kg 43.5kg 2.4kg (Bass Blaster Unit) TV RF System Color System TV Mode NTSC3.58 Video Mode NTSC3.58 / NTSC4.43 / PAL...
SECTION 1 PRECAUTION 1.1 SAFETY PRECAUTIONS (1) The design of this product contains special hardware, (8) When service is required, observe the original lead dress. many circuits and components specially for safety Extra precaution should be given to assure correct lead dress in the high voltage circuit area.
In accordance with the brightness in a room, the brightness and/or contrast of the picture can be adjusted automatically to make the optimum picture which is easy on the eye. Built-in OFF TIMER & RETURN +. • 2.2 MAIN DIFFERENCE LIST Items AV-29VT11/P AV-29VT31/P AV-29VT11/T MAIN PWB ASS’Y SCH-1176A-H2 SCH-1178A-H2 SCH-1177A-H2 CRT SOCKET PWB ASS’Y...
Page 5
2.3 FUNCTIONS REMOTE CONTROL UNIT RM-C1331-1H [AV-29VT11/P, AV-29VT11/T] MUTING key POWER key POWER MUTING COLOR SYSTEM key CINEMA SURROUND key COLOR CINEMA SYSTEM SURROUND DISPLAY key ECO SENSOR key DISPLAY SENSOR MENU ( / , / ) keys Number keys...
Page 6
POWER lamp CHANNEL (-/+) buttons MAIN POWER button REAR TERMINAL 10 11 10 11 BASS BASS SPEAKER SPEAKER [AV-29VT31/P] [AV-29VT11/P, AV-29VT11/T] COMPONENT (VIDEO-2) INPUT TERMINAL VIDEO-1 INPUT TERMINAL Y/VIDEO S-VIDEO VIDEO AUDIO L/MONO AUDIO L/MONO AUDIO R AUDIO R OUTPUT TERMINAL...
SECTION 3 DISASSEMBLY 3.1 DISASSEMBLY PROCEDURE 3.1.1 REMOVING THE TWIN PORT BASS BLASTER UNIT 3.1.6 REMOVING THE SPEAKER [AV-29VT31/P] • Remove the REAR COVER. (1) Remove the 2 screws [G] as shown in Fig.1. • Unplug the power supply cord. (2) Withdraw the SPEAKER backward.
Page 8
PICTURE TUBE [FRONT SIDE] CONTROL BASE (X2) FRONT CABINET CHASSIS SPEAKER BASE Fig.2 SOCKET PWB FRONT CONTROL PWB (2/2) MAIN PWB CLAW B FRONT CONTROL (under side) PWB (1/2) SPEAKER AV TERMINAL Fig.2 BOARD (X2) CONTROL BASE CHASSIS BASE CLAW B (under side) (×4) BASS SPEAKER OUT JACK...
Page 9
3.2 REPLACEMENT OF MEMORY IC 3.2.1 MEMORY IC SERVICE MENU This TV uses the following memory IC. Memory IC: IC1702 on MAIN PW Board SERVICE MENU The memory IC memorizes data for correctly operating the 1. IF 2. VC video and deflection circuits. When replacing the memory 3.
Page 10
3.2.3 FACTORY SETTING VALUE SETTING OF SYSTEM CONSTANT SET Setting value Setting item Setting content AV-29VT11/P AV-29VT31/P AV-29VT11/T ← ← TRIPLE NTSC COLOR SYSTEM NTSC ← ← NTSC COMB NTSC ← ← TILT SUPER BASS ← E/S/P LANGUAGE E/S/P ←...
Page 11
%SETTING OF SWITCHES ON FRONT PANEL AND REMOTE CONTROL UNIT Setting item Setting value POWER SUB POWER VOLUME COLOR SYSTEM NTSC SOUND SYSTEM PICTURE MODE (VSM) BRIGHT CINEMA SURROUND SUPER BASS ON [AV-29VT31/P] CLOSED CAPTION OFF (CC1/T1) OFF TIMER CHANNEL POSITION CH-02 Table 2 %SETTING OF MENU SCREEN...
Page 12
%SERVICE MENU SETTING ITEMS Service menu Setting item Service menu Setting item 1. IF 1. VCO 5. PRESET 1. PSNS 2. DELAY POINT [Do not adjust] 2. ACL 3. MUS 4. MAT 2. VC 1. CUTOFF(R/G) 5. FCO 2. DRIVE(R/G/B) 6.
Page 13
3.3 REPLACEMENT OF CHIP COMPONENT 3.3.1 CAUTIONS (1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it. 3.3.2 SOLDERING IRON (1) Use a high insulation soldering iron with a thin pointed end of it.
SECTION 4 ADJUSTMENT 4.1 ADJUSTMENT PREPARATION (1) You can make the necessary adjustments for this unit with either the remote control unit or with the adjustment equipment and parts as given below. (2) Adjustment with the remote control unit is made on the basis of the initial setting values, however, the new setting values which set the screen to its optimum condition may differ from the initial settings.
Page 15
4.4 ADJUSTMENT LOCATIONS FRONT CONTROL PWB ASS’Y (1/2) FRONT CONTROL PWB ASS’Y (2/2) FRONT FRONT S805 S801 S803 J304 J303 J302 J801 POWER S804 S806 S802 S801 : CH UP + CN002 S802 : CH DOWN – S901 S803 : MENU CN003 CN002 S804 : TV/VIDEO...
Page 16
4.5 BASIC OPERATION IN SERVICE MENU 4.5.1 TOOL OF SERVICE MENU OPERATION Operate the SERVICE MENU with the remote control unit. 4.5.2 SERVICE MENU ITEMS With the SERVICE MENU,various settings (adjustments) can be made,and they are broadly classified in the following items of settings: 1.
Page 17
4.5.4 SERVICE MENU FLOW CHART SUB MENU 1. IF SERVICE MENU SERVICE MENU 1. IF 2. VC VCO (CW) ***** 3. DEF 4. VSM PRESET TOO HIGH 5. PRESET 6. AUDIO 1. VCO ABOVE REFERENCE 7. PLUG & PLAY (ON) BELOW REFERENCE 2.
Page 18
4.6 ADJUSTMENT PROCEDURE 4.6.1 B1 POWER SUPPLY Measuring Item Test point Adjustment part Description instrument Signal B1 (pin 1) (1) Receive a black and white signal. B1 POWER SUPPLY generator GND (pin 5) (2) Connect a DC voltmeter between B1 and GND (between [CN00S pins 1 and 5 of the connector CN00S).
Page 20
Measuring Item Test point Adjustment part Description instrument WHITE Signal [2. VC] Notes: • generator 2.DRIVE (R) BALANCE Proceed to the following adjustment after having completed (High light) 2.DRIVE (G) the WHITE BALANCE (Low light) adjustment. Remote 2.DRIVE (B) adjustment •...
Page 21
(5) Connect the oscilloscope between TP-47G and TP-E. (6) Adjust NTSC 3.58 COLOR to set the value (A) in the figure to +4V [AV-29VT11/P, AV-29VT31/P] or +6V [AV-29VT11/T]. - NTSC 4.43 COLOR - When adjustment is done for NTSC 3.58 COLOR, appropriate values are automatically set for NTSC 4.43 COLOR.
Page 22
(6) Connect the oscilloscope between TP-47G and TP-E. (–) (7) Adjust NTSC 3.58 TINT to set the value (B) in the figure to +2V [AV-29VT11/P, AV-29VT31/P] or +7V [AV-29VT11/T]. (8) Press the [DISPLAY] key twice to return to the normal screen.
Page 23
4.6.5 DEFLECTION CIRCUIT ADJUSTMENTS • The setting (adjustment) using the remote control unit is made on the basis of the initial setting values. • The setting values which adjust the screen to the optimum condition can be different from the initial setting values. •...
Page 24
Measuring Item Test point Adjustment part Description instrument [3. DEF] - PAL V. HEIGHT - V. HEIGHT Signal adjustment 2. VER. HEIGHT (1) Input a PAL cross-hatch signal. generator 13. V. ZOOM (2) Select 2. VER. HEIGHT. (3) Set the initial setting value of 2. VER. HEIGHT. Remote (4) Select 13.
Page 25
Measuring Item Test point Adjustment part Description instrument SIDE PIN [3. DEF] - PAL SIDE PIN - Signal adjustment 7. EW-PIN (1) Input a PAL cross-hatch signal. generator (2) Select 7. EW-PIN. (3) Set the initial setting value of 7. EW-PIN. Remote (4) Adjust 7.
Page 26
Measuring Item Test point Adjustment part Description instrument [3. DEF] - PAL CORNER - CORNER Signal adjustment 9. UP CORNER (1) Input a PAL cross-hatch signal. generator 10. DW CORNER (2) Select 9. UP CORNER. (3) Set the initial setting value of 9. UP CORNER. Remote (4) Select 10.
Page 27
COMPRESS : ON (16:9), fv: 50Hz/60Hz mode Measuring Test point Adjustment part Description Item instrument V. HEIGHT Signal [3.DEF] - PAL V. HEIGHT - generator 13. V. ZOOM (1) Input a PAL cross-hatch signal of vertical frequency 50Hz. adjustment 2. VER. HEIGHT (2) Select COMPRESS from the MENU and set COMPRESS Remote to ON.
Page 28
Measuring Item Test point Adjustment part Description instrument [3. DEF] - PAL SIDE PIN - SIDE PIN Signal adjustment 7. EW-PIN (1) Input a PAL cross-hatch signal. generator (2) Select 7. EW-PIN. (3) Set the initial setting value of 7. EW-PIN. Remote (4) Adjust 7.
Page 29
VIDEO - 2 SET : COMPONENT, fv: 50/60Hz mode Measuring Item Test point Adjustment part Description instrument H. POSITION [3. DEF] (1) Input a PAL circle pattern signal to VIDEO-2 terminal. Signal adjustment 5. HOR. POSITION (2) Select VIDEO-2 SET from the MENU and set VIDEO-2 generator SET to COMPONENT.
Page 30
4.6.7 PRESET SETTING • Do not adjust 5. PRESET in the SERVICE MENU as it requires no adjustment. [SUB MENU 5. PRESET] Initial setting value Setting item Variable range AV-29VT11/P AV-29VT31/P AV-29VT11/T ← 1. PSNS 2. ACL ← ← 3. MUS ←...
SECTION 5 TROUBLESHOOTING 5.1 SELF CHECK FUNCTIONS 5.1.1 OUTLINE This model has self check functions given below. When an abnormality has been detected, the SUB POWER is turned off and POWER LED flash to inform of the failure. An abnormality is detected by the signal input state of the control line connected to the microcomputer.
Page 32
PARTS LIST CAUTION The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the safety. The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied. P.W.
Page 33
MAIN P.W. BOARD ASS'Y (SCH-1176A-H2) ....................3-17 CRT SOCKET P.W. BOARD ASS'Y (SCH-3009A-H2) ..................3-20 FRONT CONTROL P.W. BOARD ASS'Y (SCH-8006A-H2) ................3-21 REMOTE CONTROL UNIT PARTS LIST (RM-C1331-1H) [AV-29VT11/P, AV-29VT11/T] ........3-22 REMOTE CONTROL UNIT PARTS LIST (RM-C1330-1H) [AV-29VT31/P] .............. 3-22 PACKING ................................... 3-23 PACKING PARTS LIST .............................
EXPLODED VIEW PARTS LIST -1 Ref.No. Part No. Part Name Description Local GG20028-001A-H OPERATION SHEET CM48229-00A-C DOOR LATCH LC41540-002B JVC MARK QYNSS2000P PUSH NUT CM35235-003-H SPRING GG30050-001B-H REMOCON LENS GG30049-001B-H LED LENS 100 GG10239-004A-H FRONT CABINET ASS'Y Inc.101,102...
EXPLODED VIEW -2 FRONT CABINET FRONT CONTROL PWB (2/2) SOCKET PWB MAIN PWB FRONT CONTROL PWB (1/2) T1551 BASS SPEAKER OUT JACK [AV-29VT31/P] TWIN PORT BASS BLASTER UNIT [AV-29VT31/P] (No.52195) 3-5...
EXPLODED VIEW PARTS LIST -3 [AV-29VT31/P] Ref.No. Part No. Part Name Description Local LC40352-001A-H RUBBER SHEET (x4) QYSBSFG4016Z TAP SCREW 4.0mm x 16mm(x13) GG10141-001C-H BASS BOTTOM LC41211-001A SOUND ABSORBER QYSBSFG4016Z TAP SCREW 4.0mm x 16mm(x4) QAS0118-001 SPEAKER SP03 WJJ0266-002A E-SIC WIRE C-C GG30022-001A-H BASS DUCT R...
PRINTED WIRING BOARD PARTS LIST [AV-29VT11/P] Ref No. MAIN P.W. BOARD ASS'Y (SCH-1176A-H2) Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1902 MTZJ33B-T2 Z DIODE D1906 MTZJ27B-T2 Z DIODE IC1301 TDA9181T/N1-X D1907 MTZJ33B-T2 Z DIODE...
Page 39
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local C1541 QETN2EM-106Z E CAPACITOR 10uF 250V M C1746 NDC31HJ-101X C CAPACITOR 100pF 50V J C1550 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J C1747 NCB31HK-473X C CAPACITOR 0.047uF 50V K C1591 QETN1CM-107Z...
Page 40
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local R1603 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R1001 NRSA63J-221X MG RESISTOR 220Ω 1/16W J R1604 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R1002 NRSA63J-221X MG RESISTOR 220Ω...
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local R1810 NRSA63J-823X MG RESISTOR 82kΩ 1/16W J L1702 QQL244K-100Z PEAKING COIL 10uH K R1811 NRSA63J-391X MG RESISTOR 390Ω 1/16W J L1731 QQL244J-101Z PEAKING COIL 100uH J R1812 NRSA63J-104X...
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local Q3262 2SA1530A/QR/-X TRANSISTOR R3160 NRSA63J-101X MG RESISTOR 100Ω 1/16W J Q3263 2SA1530A/QR/-X TRANSISTOR R3166 QRZ0107-152Z C RESISTOR 1.5kΩ 1/2W K Q3264 2SC3928A/QR/-X TRANSISTOR R3170 QRZ0107-474Z C RESISTOR 470kΩ...
Page 43
Ref No. Part No. Part Name Description Local D8802 P1241-04 PHOTO CONDUCTOR D8803 LH22440-T16 POWER C8481 NCB21EK-224X C CAPACITOR 0.22uF 25V K C8482 NCB21EK-224X C CAPACITOR 0.22uF 25V K C8483 NCB21EK-224X C CAPACITOR 0.22uF 25V K C8484 NCB21EK-224X C CAPACITOR 0.22uF 25V K C8485 QETN1EM-476Z...
PRINTED WIRING BOARD PARTS LIST [AV-29VT31/P] Ref No. MAIN P.W. BOARD ASS'Y (SCH-1178A-H2) Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1733 MA111-X SI DIODE D1801 MA3120/M/-X Z DIODE IC1301 TDA9181T/N1-X D1802 MA3120/M/-X Z DIODE IC1401 LA78041 D1901...
Page 45
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local C1533 QEHR1EM-108Z E CAPACITOR 1000uF 25V M C1739 NFV91CJ-104X MPPS CAPACITOR 0.1uF 16V J C1534 QCB32HK-561Z C CAPACITOR 560pF 500V K C1740 QETN1HM-225Z E CAPACITOR 2.2uF 50V M C1536 QFLC1HJ-103Z...
Page 46
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local R1547 C1983 QETN1CM-227Z E CAPACITOR 220uF 16V M QRL029J-221 OMF RESISTOR 220Ω 2W J C1984 NCB31CK-104X C CAPACITOR 0.1uF 16V K R1591 QRA14CF-1202Y CMF RESISTOR 12kΩ...
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local R1750 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R1973 QRE121J-332Y C RESISTOR 3.3kΩ 1/2W J R1755 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R1974 QRL029J-220 OMF RESISTOR 22Ω...
PRINTED WIRING BOARD PARTS LIST [AV-29VT11/T] Ref No. MAIN P.W. BOARD ASS'Y (SCH-1176A-H2) Part No. Part Name Description Local Ref No. Part No. Part Name Description Local D1902 MTZJ33B-T2 Z DIODE D1906 MTZJ27B-T2 Z DIODE IC1301 TDA9181T/N1-X D1907 MTZJ33B-T2 Z DIODE IC1401 LA78041 D1908...
Page 49
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local C1541 QETN2EM-106Z E CAPACITOR 10uF 250V M C1746 NDC31HJ-101X C CAPACITOR 100pF 50V J C1550 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J C1747 NCB31HK-473X C CAPACITOR 0.047uF 50V K C1591 QETN1CM-107Z...
Page 50
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local R1603 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R1001 NRSA63J-221X MG RESISTOR 220Ω 1/16W J R1604 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R1002 NRSA63J-221X MG RESISTOR 220Ω...
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local R1810 NRSA63J-823X MG RESISTOR 82kΩ 1/16W J L1702 QQL244K-100Z PEAKING COIL 10uH K R1811 NRSA63J-391X MG RESISTOR 390Ω 1/16W J L1731 QQL244J-101Z PEAKING COIL 100uH J R1812 NRSA63J-104X...
Ref No. Ref No. Part No. Part Name Description Local Part No. Part Name Description Local Q3261 2SA1530A/QR/-X TRANSISTOR R3150 QRZ0107-152Z C RESISTOR 1.5kΩ 1/2W K Q3262 2SA1530A/QR/-X TRANSISTOR R3152 NRSA63J-101X MG RESISTOR 100Ω 1/16W J Q3263 2SA1530A/QR/-X TRANSISTOR R3160 NRSA63J-101X MG RESISTOR 100Ω...
REMOTE CONTROL UNIT PARTS LIST (RM-C1331-1H) [AV-29VT11/P, AV-29VT11/T] Ref No. Part No. Part Name Description Local R25-8173 BATTERY COVER REMOTE CONTROL UNIT PARTS LIST (RM-C1330-1H) [AV-29VT31/P] Ref No. Part No. Part Name Description Local R25-8173 BATTERY COVER 3-22 (No.52195)
PACKING Set SP. WIRE on this space PACKING PARTS LIST Ref.No. Part No. Part Name Description Local GG10044-065A-H PACKING CASE AV-29VT11/P,AV-29VT11/T GG10044-066A-H PACKING CASE AV-29VT31/P GG10193-001D-H CUSHION ASS'Y 8pcs in 1set GG20011-008A-H SUPPORT PAD GG20011-009A-H SUPPORT PAD GG20011-009A-H SUPPORT PAD...
Page 55
AV-29VT11 , AV-29VT31 , AV-29VT11 STANDARD CIRCUIT DIAGRAM NOTE ON USING CIRCUIT DIAGRAMS ! ! ! ! ! • 1. SAFETY Type The components identified by the ! ! ! ! ! symbol and shading No indication : Ceramic capacitor are critical for safety.
Page 56
CONTENTS SEMICONDUCTOR SHAPES ............................ 2-2 BLOCK DIAGRAM ................................2-3 CIRCUIT DIAGRAMS MAIN PWB CIRCUIT DIAGRAM (1/2) ..........................2-5 MAIN PWB CIRCUIT DIAGRAM (2/2) ..........................2-7 CRT SOCKET PWB CIRCUIT DIAGRAM ......................... 2-9 FRONT CONTROL PWB CIRCUIT DIAGRAM ......................2-11 PATTERN DIAGRAMS MAIN PWB PATTERN ..............................
BLOCK DIAGRAM IC701 MAIN MICROCOMPUTER, TELETEXT DECODER, MAIN PWB VIDEO/SYNC/DEF PROCESSOR TU001 TUNER 28, 29 SF101 SIF IN QSS OUT Q150 SAW FILTER IC601 SOUND BUFFER 30,31 L,R MULTI SOUND PROCESSOR VIDEO 23, 24 IF VOUT SF102 IF IN SAW FILTER DETECT SELECT MATRIX...
VOLTAGE CHART Note : • Mark * expresses the portion into which a voltage value is changed. <CRT SOCKET PWB> <FRONT PWB> <MAIN PWB> PIN NO. VOLTAGE(V) PIN NO. VOL AGE(V) PIN NO. VOLTAGE(V) PIN NO. VOL AGE(V) PIN NO. VOLTAGE(V) PIN NO.