Sealey CP108VCSBO Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Always work with the saw safety guard in place.
‰
Maintain the tool and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the tool is switched off before installing the battery pack.
9
Keep the tool and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the tool; e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
Ensure battery pack is correctly inserted into the handle and latched in place before attempting to switch on tool.
9
Check the blade to ensure that it is not split, cracked or damaged in any way. If in doubt DO NOT use the blade.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep direction switch in the locked position until the tool is required for use.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the tool.
8
DO NOT operate the tool if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT switch the saw on whilst the blade is in contact with the workpiece.
8
DO NOT leave the tool operating unattended.
8
DO NOT carry the tool with your finger on the power switch.
8
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the tool or battery charger wet or use in damp or wet locations.
8
DO NOT touch the workpiece immediately after cutting as it will be very hot.
8
DO NOT hold unsecured work in your hand and DO NOT touch the saw blade whilst operating
8
DO NOT leave the saw running unattended and DO NOT lay it down whilst it is running.
8
DO NOT cover the saw air vents. To do so will overheat the machine.
8
WARNING! DO NOT use on materials containing asbestos.
‰
2. INTRODUCTION
Compact, lightweight cordless circular saw - body only. Comfortable housing with soft grip to help reduce vibration. Supplied with
1 x wrench for removing and replacing blades. Requires compatible 10.8V 2Ah or 4Ah battery and mains charger, sold separately.
3. SPECIFICATION
Model No: .......................................................CP108VCSBO
Blade Diameter ......................................................... Ø85mm
Consumable Parts ........................................................ ........
CP108VBP 2Ah Battery (not included)
CP108VBP4 4Ah Battery (not included)
Cutting Depth at 90 ..................................................... 26mm
o
Cutting Depth at 45 ..................................................... 17mm
o
Disk Bore Size .......................................................... Ø15mm
Noise Power/Pressure ......................................... 88/77dB(A)
No-load speed .......................................................0-1450rpm
Replacement parts .....................CP108VMC - mains charger
Vibration/uncertainty ........................................ 3.368/1.5m/s²
4. PREPARATION
© Jack Sealey Limited
10.8V Ø85MM CORDLESS CIRCULAR SAW -
BODY ONLY
MODEL NO:
Wear protective
Wear safety
gloves
footwear
Original Language Version
CP108VCSBO
Wear protective Wear ear
clothing protection
Wear a mask
CP108VCSBO Issue 1 19/04/21