Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5 INTRODUCTION 5 Common Icons...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures, which could result in an accident or bodily injury. It also contains CAUTIONS against procedures, which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....10 Ignition Key Removal ....10 Automatic Transaxle Ignition Interlock System .
Page 8 8 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Program Transmitters ....20 General Information ....20 Battery Replacement .
Page 9 Airbag System Components ....41 Front Seat Airbag Features ....42 Airbag Deployment Sensors And Controls ..47 Event Data Recorder (EDR) .
Page 10: Things To Know Before Starting Your Vehicle 7
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 11: Automatic Transaxle Ignition Interlock System
ignition cylinder to warn you that this safety feature is inoperable. The engine can be started and stopped but the key cannot be removed until you obtain service. NOTE: The power window switches, radio, and power outlets, will remain active for up to 45 seconds after the ignition switch has been turned off.
Page 12: Locking Doors With The Key
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locking Doors With The Key There is only one external door lock cylinder which is located in the driver’s door only. You can insert the key with either side up. To lock the door, turn the key rearward, to unlock the door, turn the key forward.
Page 13: Replacement Keys
• Exxon/Mobil Speed Pass,™ additional Sentry Keys, or any other transponder equipped components on the same keychain will not cause a key-related (tran- sponder) fault unless the additional part is physi- cally held against the ignition key being used when starting the vehicle. Cell phones, pagers, or other RF electronics will not cause interference with this system.
Page 14: General Information
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound. The Theft Alarm Light will stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed.
Page 15: To Disarm The System
3. The indicator light in the instrument cluster will flash rapidly for 16 seconds. This shows that the system is arming. During this period, if a door is opened, the ignition switch is turned ON, or the power door locks are unlocked in any manner, the system will automatically disarm.
Page 16: Security System Manual Override
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tamper Alert If the alarm was triggered, but the warning signals have timed out, the park and taillights flash three times (instead of the normal twice) when unlocking the vehicle with a valid Remote Keyless Entry (RKE) transmitter to alert the driver.
Page 17: Remote Keyless Entry
REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors and trunk or activate the panic alarm from distances a maxi- mum of 66 feet (20 meters) using a hand held radio transmitter. The transmitter need not be pointed at the vehicle to activate the system.
Page 18: To Lock The Doors
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Press and hold the LOCK button on a programmed key fob. 2. Continue to hold the LOCK button at least 4 seconds, but not longer than 10 seconds, then press and hold the UNLOCK button.
Page 19: Using The Express Down Window Feature - If Equipped
Using The Express Down Window Feature — If Equipped The key fob remotely lowers both driver and passenger front windows simultaneously. Lowering the front win- dows using the key fob is a two step operation: 1. Press the unlock button once. 2.
Page 20: To Program Transmitters
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Pressing the LOCK button on the key fob, while you are in the vehicle, will activate the Security Alarm. Opening a door with the Security Alarm activated will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm.
Page 21: Remote Start System - If Equipped
Separating Transmitter Halves 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. 3. To assemble the transmitter case, snap the two halves together.
Page 22 22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE START BUTTON To exit the Remote Start mode, allow the engine to run the cycle or depress the unlock button to disarm the Vehicle Theft Security Alarm and within one minute insert the key into the ignition and turn the ignition to the RUN position.
Page 23: Door Locks
• Battery is at an acceptable charge level • Panic button on key fob is not depressed DOOR LOCKS Manual Door Locks Use the manual door lock plunger to lock the doors from inside the vehicle. If the plunger is down when the door is closed, the door will lock.
Page 24: Power Door Locks
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. Power Door Locks A door lock switch is located on the driver and passenger door panel.
Page 25: Child-Protection" Door Lock System (Rear Doors)
2. Cycle the ignition switch between LOCK, and ON, and back to LOCK 4 times ending up in the LOCK position. 3. Depress the power door lock switch to lock the doors. 4. A single chime will indicate the completion of the programming.
Page 26: Power Windows
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE or similar flat-bladed object into the lock and rotate approximately ⁄ turn to the lock or unlock position (as indicated by the stamped icons). Child Lock Control WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged.
Page 27: Auto Window Up (Express Up) With Anti-Pinch
window will go down automatically. To cancel the Auto Down movement, operate the switch either in the up or down direction and release the switch. Power Window Auto Up / Auto Down Switches NOTE: The convenience of one-touch down front win- dows, can also be controlled by using the remote key fob —...
Page 28: Window Lockout Switch
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To close the window part way, lift the window switch to the first detent and release it when you want the window to stop. NOTE: • If the window runs into any obstacle during auto- closure, it will reverse direction and then stop.
Page 29: Reset Express Up
Reset Express Up Any time the vehicle battery is disconnected, or goes dead, the auto-up function will be disabled. To reactivate the auto-up feature, pull the window switch up to close the window completely and continue to hold the switch up for an additional two seconds after the window is closed.
Page 30: Trunk Safety Warning
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE With the ignition ON, the word “deck” will display in place of the odometer display indicating that the trunk is open. The odometer display will reappear once the trunk is closed or if the trip button is depressed. With the key in the lock position or with the key out, the word “deck”...
Page 31: Occupant Restraints
OCCUPANT RESTRAINTS Some of the most important safety features in your vehicle are the restraint systems. The following safety features are standard on all vehicles: • Three point lap and shoulder belts for all seating positions • Pretensioning and load-limiting retractors for the front seat belts •...
Page 32: Lap/Shoulder Belts
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 33 WARNING! • Be sure everyone in your vehicle is in a seat and using a seat belt properly. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 35 WARNING! • A belt that is worn under your arm is very dangerous. Your body could strike the inside sur- faces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 37: Adjustable Upper Shoulder Belt Anchorage
Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push anchorage button to release the anchor- age, and move it up or down to the position that serves you best.
Page 38: Rear Seat Belts
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How To Disengage The Automatic Locking Mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic lock- ing mode and activate the vehicle sensitive (emergency)
Page 39: Seat Belts And Pregnant Women
The Enhanced Warning System (BeltAlert) will be reacti- vated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). Belt Alert Programming BeltAlert can be enabled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON...
Page 40: Seat Belt Extender
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender If a seat belt is too short, even when fully extended and when the adjustable upper shoulder belt anchorage (if equipped) is in its lowest position, your dealer can provide you with a seat belt extender.
Page 41: Airbag System Components
NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment. The front airbags have a multistage inflator design. This may allow the airbag to have different rates of inflation that are based on collision severity and occupant size. This vehicle may also be equipped with window bags to protect the driver, front, and rear passengers sitting next to a window.
Page 42: Front Seat Airbag Features
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Seat Airbag Features The front airbag system has dual-stage driver and front passenger airbags. This system provides output appro- priate to the level of crash severity as determined by the Occupant Restraint Controller (ORC) and the impact sensors at the front of the car.
Page 43 Seat-mounted Side Airbag Label When the bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each bag deploys independently, that is a left side impact deploys the left bag only and a right-side impact deploys only the right bag.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag covers may not be obvious in the NOTE: interior trim; but they will open to allow airbag deploy- ment. The system includes sensors adjacent to both front and rear seat occupants that are calibrated to deploy during an impact severe enough to require airbag occupant protection.
Page 45 Airbags inflate in moderate to high speed impacts. Along with seat belts and pretensioners, front airbags work with the knee bolsters to provide improved protection for the driver and front passenger. Side airbags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. All occupants should wear their lap and shoulder belts properly. 3. The driver and front passenger seats should be moved back as far as practical to allow the front airbags room to inflate. 4.
Page 47: Airbag Deployment Sensors And Controls
Airbag Deployment Sensors and Controls Occupant Restraint Controller (ORC) The Occupant Restraint Controller System (ORC) is part of a Federally regulated safety system required for this vehicle. The ORC determines if a frontal collision is severe enough to require the airbags to inflate. Based on the sensor signals, a central electronic Occupant Restraint Controller (ORC) deploys the front airbags, side inflat- able airbag curtains, seat-mounted side (Thorax) airbags,...
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Ignoring the AIRBAG light in your instrument panel could mean you won’t have the airbags to protect you in a collision. If the light does not come on, stays on after you start the vehicle, or if it comes on as you drive, have the airbag system checked right away.
Page 49 The following requirements must be strictly adhered to: • Do not make any modifications to the front passenger seat components, assembly, or to the seat cover in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Turns on the interior lamps which remain on as long as the battery has power or until the ignition key is removed. • Unlocks the doors automatically If A Deployment Occurs The airbag systems are designed to deploy when the Occupant Restraint Controller (ORC) detect a moderate- to-severe collision, to help restrain the driver and front...
Page 51 • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you. WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, seat belt pretensioners, and the front passenger seat belt retractor assembly, replaced by an authorized dealer as soon as possible.
Page 52: Event Data Recorder (Edr)
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Do not attempt to modify any part of your advanced airbag system. The airbag may inflate accidentally or may not function properly if modifications are made. Take your vehicle to an authorized dealer for any advanced airbag system service.
Page 53 NOTE: 1. A near-deployment event occurs when the airbag sensor detects severe vehicle deceleration usually indica- tive of a crash, but not severe enough to warrant airbag deployment. 2. Under certain circumstances, EDR data may not be recorded (e.g., loss of battery power). In conjunction with other data gathered during a com- plete accident investigation, the electronic data may be used by DaimlerChrysler Corporation and others to learn...
Page 54: Child Restraint
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning lamp status for electronically-controlled safety systems, including the airbag system • Airbag disable lamp status (if equipped) • Time of airbag deployment (in terms of ignition cycles and vehicle mileage) •...
Page 55 Infants And Small Children There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat owner’s manual to ensure you have the correct seat for your child. Use the restraint that is correct for your child.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Page 57 • If the seat belt has a switchable retractor, it will have a distinctive label. To operate the switchable retractor, please refer to Automatic-Locking Retractor (ALR) in this section. • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle’s seat belt at the center position. If your child restraints are not LATCH-compatible, you can only in- stall the child restraints using the vehicle’s seat belts. Please refer to “Installing the Child Restraint System” for typical installation instructions.
Page 59 NOTE: When using the LATCH attaching system to install a child restraint, please ensure that all seat belts not being used for occupant restraints are stowed and out of reach of children. It is recommended that before installing the child restraint, buckle the seat belt so the seat belt is tucked behind the child restraint and out of reach.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You will first loosen the adjusters on the lower straps and on the tether strap so that you can more easily attach the hooks or connectors to the vehicle anchorages. Next, attach the lower hooks or connectors over the top of the seat cover material.
Page 61 1 — Cover 3 — Attaching Strap A — Tether Strap and Hook B — Tether Anchor 2. Route the tether strap to provide the most direct path for the strap between the anchor and the child seat. If your vehicle is equipped with adjustable rear head restraints, raise the head restraint, and where possible, route the tether strap under the head restraint and THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61...
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight; however, any seat belt system will loosen with time, so check the belt occasionally, and pull it tight if necessary.
Page 63: Engine Break-In Recommendations
• Make sure that the child is upright in the seat. • The lap portion should be low on the hips and as snug as possible. • Check belt fit periodically. A child’s squirming or slouching can move the belt out of position. •...
Page 64: Safety Tips
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be considered as a normal part of the break-in and not interpreted as an indication of difficulty. SAFETY TIPS Exhaust Gas WARNING!
Page 65: Periodic Safety Checks You Should Make Outside The Vehicle
turned ON. If the LED is not lit during starting, have it checked. If the light stays on or comes on while driving, have the system checked by an authorized dealer. Defroster Check operation by selecting the defrost mode and place the blower control on high speed.
Page 67: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......70 Inside Day/Night Mirror— If Equipped ..70 Automatic Dimming Mirror—...
Page 68 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lights ......104 Map/Reading/Interior Lights ... . 104 Multi-Function Control Lever .
Page 69 Programming A “Rolling Code” System ..117 Canadian Programming/Gate Programming . . 118 Using HomeLink ..... 118 Erasing HomeLink Buttons .
Page 70: Mirrors
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror— If Equipped Adjust the mirror to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjusting Manual Rear View Mirror Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 71: Electric Remote-Control Mirrors
CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Electric Remote-Control Mirrors Both of the outside mirrors can be adjusted by using the remote controls mounted on the driver’s door panel.
Page 72: Adjusting Side View Mirrors
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mirror Directions Adjusting Side View Mirrors Outside Mirror — Driver’s Side Adjust the outside mirror to center on the adjacent lane of traffic, with a slight overlap of the view obtained on the inside mirror.
Page 73: Illuminated Vanity Mirrors - If Equipped
UConnect™ system. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro-...
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The UConnect™ phone book enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phone book accessible only in that language. This system is driven through your Blue- tooth™...
Page 75: Operations
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., Headset Profile) you may not be able to use any UCon- nect™...
Page 76 One of the following vehicle specific websites may also provide detailed instructions for pairing with the brand of phone that you have: NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect The following are general phone to UConnect™ System pairing instructions:...
Page 77 • After the Ready prompt and the following beep, say Setup Phone Pairing. • When prompted, after the beep, say Pair a Phone and follow the audible prompts. • You will be asked to say a four-digit pin number, which you will later need to enter into your cellular. You can enter any four-digit pin number.
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will confirm the phone num- ber and then dial. The number will appear in the display of certain radios. Call by Saying a Name • Press the “Phone” button to begin. •...
Page 79 The UConnect™ system will allow you to enter up to 32 names in the phone book with each name having up to four associated phone numbers and designations. Each language has a separate 32-name phone book accessible only in that language. Edit Entries in the UConnect™...
Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE from which you choose. To select one of the entries from the list, press the Voice Recognition button while the UConnect™ system is playing the desired entry and say Delete. • After you enter the name, the UConnect™ system will ask you which designation you wish to delete, home, work, mobile, pager, or all.
Page 81: Phone Call Features
Phone Call Features The following features can be accessed through the UConnect™ system if the feature(s) are available on your cellular service plan. For example, if your cellular service plan provides three-way calling, this feature can be accessed through the UConnect™ system. Check with your cellular service provider for the features that you have.
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched.
Page 83: Uconnect™ System Features
until the vehicle battery condition dictates cessation of the call on the UConnect™ system and transfer of the call to the mobile phone. • After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico). The number dialed may not be applicable with the available cellular service and area. The UConnect™...
Page 85 You can use your UConnect™ system to access a voice- mail system or an automated service, such as, paging service or automated customer service. Some services require immediate response selection, in some instances, that may be too quick for use of UConnect™ system. When calling a number with your UConnect™...
Page 86: Advanced Phone Connectivity
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad You can dial a phone number with your cellular phone keypad and still use the UConnect™ system (while dialing via the cell phone keypad, the user must exercise caution and take precautionary safety measures).
Page 87 Connect or Disconnect Link Between the UConnect™ System and Cellular Phone Your cellular phone can be paired with many different electronic devices, but can only be actively connected with one electronic device at a time. If you would like to connect or disconnect the Blue- tooth™...
Page 88: Things You Should Know About Your Uconnect™ System
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing. • At the next prompt, say Delete and follow the prompts.
Page 89 • Make sure that no one other than you is speaking during a voice recognition period. • Performance is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, •...
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, and • dry weather condition. • operation from driver seat. • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the UConnect™...
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91...
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93...
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location call cancel confirmation prompts continue delete dial edit emergency English erase all Espanol Fancais help home language...
Page 95: General Information
pair a phone phone pairing pairing phonebook phone book previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance transfer call try again voice training work UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 General Information...
Page 96: Seats
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Seat Adjuster After releasing the adjusting bar, apply forward and rearward body pressure to be sure the seat is latched.
Page 97 Reclining Bucket Seats The recliner control is on the side of the seat. To recline, lean forward slightly before lifting the lever, then lean back to the desired position and release the lever. Lean forward and lift the lever to return the seatback to its normal position.
Page 98: Power Seats - If Equipped
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lumbar Support — If Equipped This feature allows you to increase or decrease the amount of lumbar support. The control lever is located on the outboard side of the driver’s seatback. Turn the control lever downward to increase and upward to decrease the desired amount of lumbar support.
Page 99: Heated Seats - If Equipped
CAUTION! Do not place any article under a power seat as it may cause damage to the seat controls. Heated Seats — If Equipped WARNING! Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaus- tion or other physical condition must exercise care when using the seat heater.
Page 100: Fold Flat Front Passenger Seat
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Fold Flat Front Passenger Seat The recline handle on the front passenger seat also releases the seatback to fold forward. Seat Back Fold Forward The hard seatback features a work surface and a molded rim for retaining items stored on the seat back panel.
Page 101: Adjustable Head Restraints
Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjust the restraints so that the upper edge is as high as practical. To raise, pull up on the head restraint. To lower, depress the button on the post guide and push down on the head restraint.
Page 102: Folding Rear Seat Center Armrest
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! The rear cargo area of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children. They could be seriously injured in an accident. Children should be seated and using the proper restraint system.
Page 103: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located under the left side of the instrument panel. Hood Release Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Then lift the secondary latch located under the front edge of the hood, near the center and raise the hood.
Page 104: Lights
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Use the hood prop rod to secure the hood in the open position. Place the upper end of the prop rod in the hole on the left underside of the hood. Hood Prop Rod Hole Location Before closing the hood, make sure to stow the prop rod in its proper location.
Page 105: Multi-Function Control Lever
To protect the battery, the interior lights will turn off automatically 10 minutes after the ignition switch is moved to the LOCK position. This will occur if the interior lights were switched on manually or are on because a door is open. This includes the glove box light, but not the trunk light.
Page 106: Automatic Headlight System - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, rotate the center portion of the Multi-Function Control Lever up or down. Dimmer Control Automatic Headlight System — If Equipped Turning the end of the multi-function control lever to the third detent, “A”...
Page 107: Daytime Running Lights (Drl) - If Equipped
Daytime Running Lights (DRL) — If Equipped The high beam lights will come on as Daytime Running Lights (DRL) at DRL intensity (lower), whenever the ignition is on, the engine is running, the headlight switch is off, the parking brake is off, the turn signal is off, and the gearshift lever is in any position except park.
Page 108: Turn Signals
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent.
Page 109: Windshield Wipers And Washers
WINDSHIELD WIPERS AND WASHERS The wipers and washers are operated by a switch on the control lever. The lever is located on the right side of the steering column. Windshield Wiper / Washer Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Windshield Washers To use the washer, pull the multi-function control lever toward you and hold while spray is desired.
Page 110: Mist Feature
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Push down on the wiper control lever to activate a single wipe to clear the windshield of road mist or spray from a passing vehicle. As long as the lever is held down, the wipers will continue to operate.
Page 111: Windshield Wiper Operation
Windshield Wiper Operation Turn to the second detent for low wiper speed and the third detent for high wiper speed. Wiper Control Speed Sensitive Intermittent Wiper System Use the intermittent wiper when weather conditions make a single wiping cycle, with a variable pause be- tween cycles, desirable.
Page 112: Tilt/Telescoping Steering Column
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping control handle is located below the steering wheel at the end of the steering column.
Page 113: Electronic Speed Control - If Equipped
ELECTRONIC SPEED CONTROL — IF EQUIPPED When engaged, this device takes over the accelerator operation at speeds greater than 25 mph (40 km/h). The speed control lever is located on the right side of the steering wheel. Speed Control Location To Activate: Push the ON/OFF button located in the end of the Electronic Speed Control Lever.
Page 114: To Deactivate
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The vehicle should be traveling at a steady speed and on level ground before pressing the SET lever. To Deactivate: A soft tap on the brake pedal, pulling the speed control lever towards you “CANCEL”, or normal brake pressure while slowing the vehicle will deactivate speed control without erasing the set speed memory.
Page 115: To Accelerate For Passing
To Accelerate For Passing: Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. Using Speed Control On Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal.
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE in the hand-held transmitter of the device being pro- grammed. This will allow for quicker training and accu- rate transmission of the radio-frequency signal. If your garage door opener (located in the garage) is equipped with an antenna, make sure that the antenna is hanging straight down.
Page 117: Programming A "Rolling Code" System
4. The indicator light in the Universal Transceiver will begin to flash, first slowly and then rapidly. The rapid flashing indicates successful programming. If after 90 seconds the indicator light does not flash rapidly or goes out, return to step 1 and repeat the procedure. To train the other buttons, repeat steps 3 and 4.
Page 118: Canadian Programming/Gate Programming
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE training process. Some garage door openers may require you to do this procedure a third time to complete the training. Canadian Programming/Gate Programming Canadian radio-frequency laws require transmitter sig- nals to time-out (or quit) after several seconds of transmission, which may not be long enough for HomeLink to pick up the signal during programming.
Page 119: Reprogramming A Single Homelink Button
Reprogramming a Single HomeLink Button To program a device with a previously trained HomeLink button, follow these steps: 1. Press and hold the Universal Transceiver button to be reprogrammed. Do not release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand held transmitter one to three inches away from the button to be trained.
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 121: Power Sunroof - If Equipped
POWER SUNROOF — IF EQUIPPED The sunroof controls are mounted between the sun visors in the Dome / Reading Lamp. Power Sunroof Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WARNING! • Never leave children in a vehicle, with the keys in the ignition switch.
Page 122: Opening Sunroof - Manual
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Manual Press the switch rearward and hold, and the sunroof will open automatically from any position. The sunroof will open fully, then stop automatically. During this opera- tion, any release of the sunroof switch will stop the sunroof.
Page 123: Sunshade Operation
Sunshade Operation The sunshade can be opened manually. However, the sunshade will open automatically as the sunroof opens. NOTE: The sunshade cannot be closed if the sunroof is open. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears.
Page 124: Electrical Power Outlets
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12-volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. The 12-volt power outlet next to the ash receiver tray (if equipped with an optional Smoker’s Package) has power available only when the ignition is on.
Page 125: Electrical Power Inverter - If Equipped
Console Interior ELECTRICAL POWER INVERTER — IF EQUIPPED There is a 115 VAC (150-Watts Maximum) outlet in the cen- ter console for added conve- nience. This outlet can power cell phones, electronics, and other low power devices. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 NOTE: Due to built-in overload protection, the inverter will shut down if the power rating is exceeded.
Page 126: Electrical Outlet Use With Engine Off
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Electrical Outlet Use With Engine Off CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 127 Optional Cup Holder Ash Receiver UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CAUTION! If your vehicle is equipped with the heated and cooled cup holder, locate the cup holder ash receiver in the forward cup holder. The optional ash receiver also comes with a cigar lighter. You may use the power outlet, located in the instrument panel below the climate control knob, or in the bottom of the console compartment, for this cigar lighter.
Page 128: Console Features
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONSOLE FEATURES Console Features The center console armrest slides forward from design position to provide added user comfort. Two cup holders, each of which can accommodate large sized fast food beverage containers. A one piece cup holder insert for both cavities can easily be removed for cleaning.
Page 129 • The lower bin can be accessed directly, without first exposing the upper bin, by operating the right latch with the armrest down. • The first storage bin can be used to hold smaller items. • The lower storage bin includes a molded-in coin holder, room for CD’s, DVD’s, and a power outlet that allows a cell phone to recharge while concealed.
Page 130: Cup Holders
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS Heated or Cooled Cup Holder — If Equipped With this feature the rear cavity of the cup holder can heat or cool the beverage container it is holding. The rear cup holder can heat from room temperature (70°F /21°C), to 140°F (60°C) or cool it to near freezing, 0°F (–20°C).
Page 131: Rear Bottle Holders
Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels. Rear Bottle Holder UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! If containers of hot liquid are placed in the bottle holder, they can spill when the door is closed, burning the occupants.
Page 133: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....136 Instrument Cluster—Base ....137 Instrument Cluster—Premium .
Page 134 134 UNDERSTANDING YOUR INSTRUMENT PANEL FM Reception ......159 Sales Code REQ — AM/FM Stereo Radio And 6–Disc CD/DVD Changer (MP3/WMA Aux Jack) .
Page 135 Operating Instructions - Hands Free Phone (If Equipped) ..186 Operating Instructions - Video Entertainment System (VES®) (If Equipped) ... . 186 Video Entertainment System —...
Page 136: Instrument Panel Features
136 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES Instrument Panel...
Page 137: Instrument Cluster-Base
UNDERSTANDING YOUR INSTRUMENT PANEL 137 INSTRUMENT CLUSTER—BASE...
Page 138: Instrument Cluster-Premium
138 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—PREMIUM 120 MPH Cluster with EVIC...
Page 139: Instrument Cluster Descriptions
INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel Gauge When the ignition switch is in the ON position, the pointer will show the level of fuel remaining in the fuel tank. 2. Fuel Door Reminder This is a reminder that the Fuel Filler Door is located on the left side of the vehicle.
Page 140 140 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Low Fuel Light When the fuel level drops to 2 gallons, the fuel symbol will light and a single chime will sound. 7. Charging System Light This light shows the status of the electrical charging system.
Page 141 The light does not show the quantity of oil in the engine. This can be determined using the procedure shown in Section 7. 12. Engine Temperature Warning Light This light warns of an overheated engine con- dition. If the engine is critically hot, a warning chime will sound 10 times.
Page 142 142 UNDERSTANDING YOUR INSTRUMENT PANEL off for 60 seconds when a system fault is detected. The flash cycle will repeat every ten minutes or until the fault condition is removed and reset. If this indicator comes on, the entire, PRNDL/ odometer, display will brighten to FULL DAYTIME INTENSITY and will not be dimmable.
Page 143 trip odometer, display the desired trip odometer to be reset then push and hold the button until the display resets (approximately 2 seconds). U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven.
Page 144 144 UNDERSTANDING YOUR INSTRUMENT PANEL 19. Electronic Throttle Control Indicator Light This red illuminated light informs you of a problem with the Electronic Throttle Control system. If a problem is detected, the light will come on while the engine is running. If the light remains lit with the engine running your vehicle will usually be drivable and not need towing, however see your dealer for service as soon as pos-...
Page 145 BAS Warning Lamp” comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light remains on after several ignition cycles, and the vehicle has been driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible.
Page 146 146 UNDERSTANDING YOUR INSTRUMENT PANEL indicated by the Brake Warning Light which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers which change fluid level condi- tions.
Page 147: Electronic Vehicle Information Center (Evic) - If Equipped
ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) – IF EQUIPPED EVIC Display Location The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display. It is located in the lower left part of the cluster below the fuel and engine tem- perature gauge. The EVIC consists of the following: •...
Page 148: Evic Functions
148 UNDERSTANDING YOUR INSTRUMENT PANEL • Right Front Turn Signal Light Out (with a single chime) • Right Rear Turn Signal Light Out (with a single chime) • RKE (Remote Keyless Entry) Battery Low (with a single chime) • Memory #1/#2 Profile Set •...
Page 149: Trip Functions
Trip Functions MENU / STEP Button Press and release the MENU / STEP button (located near the radio) until one of the follow- ing Trip Functions displays in the EVIC: • Average Fuel Economy UNDERSTANDING YOUR INSTRUMENT PANEL 149 • Distance To Empty •...
Page 150: To Reset The Display
150 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Significant changes in driving style or vehicle loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE displayed value. • When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text display of LOW FUEL.
Page 151 is calibrated. Calibrate the compass by completing one or more 360° turns (in an area free from large metal or metallic objects) until the “FLASH THE CAL” message displayed in the EVIC turns off. The compass will now function normally. Manual Compass Calibration If the compass appears erratic, inaccurate, or abnormal, you may wish to calibrate the compass manually.
Page 152 152 UNDERSTANDING YOUR INSTRUMENT PANEL Procedure to Update the Variance: 1. Turn the ignition switch to the ON position while leaving the transmission selector in PARK. 2. Press the Step Button Several Times until “Personal Settings” is displayed in the EVIC window. 3.
Page 153: Telephone - If Equipped
Telephone — If Equipped Press and release the MENU button until “Telephone” displays in the EVIC. When the appropriate conditions exist, the EVIC pro- vides the following telephone information: • Phone status: idle; voice mail; roaming; battery strength; and signal strength in increments of 20 percent.
Page 154: Navigation - If Equipped
154 UNDERSTANDING YOUR INSTRUMENT PANEL The EVIC displays this symbol to indicate that you have voice mail. Voice Mail The EVIC displays this symbol to indicate a text message. Text Message The EVIC displays this symbol to indicate the battery strength of the UConnect™ phone. Battery Strength The EVIC displays this symbol to indicate that...
Page 155: Personal Settings (Customer Programmable Features)
Turn-By-Turn Directions The EVIC displays turn-by-turn directions to a pro- grammed destination when Turn-By-Turn Navigation is enabled through Personal Settings. When enabled, the EVIC displays the name of the approaching road at the top of the screen, followed by an arrow to indicate the direction to turn the vehicle, and a count down to indicate the distance to the turn.
Page 156 156 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Key Unlock Driver Door 1st When Driver Door 1st Press is selected, only the driver’s door will unlock on the first press of the remote keyless entry unlock button. When Driver Door 1st Press is selected, you must press of the remote keyless entry unlock button twice to unlock the passenger’s doors.
Page 157: Setting The Analog Clock
Key-Off Power Display When this feature is selected, the power window switches, radio, hands–free system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch is turned off. Opening a vehicle door will cancel this feature.
Page 158: Electronic Digital Clock
158 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the frequency and/or time in hours and minutes (depending on your radio model) whenever the ignition switch is in the “ON” or “ACC”...
Page 159: Electrical Disturbances
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
Page 160: Operating Instructions - Radio Mode
160 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Press the ON/VOL control to turn the radio ON. Press the ON/VOL a second time to turn OFF the radio.
Page 161 3. After the hours are adjusted, press the right side TUNE control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE control knob. Press the TUNE control knob to save time change. 5.
Page 162 162 UNDERSTANDING YOUR INSTRUMENT PANEL MUSIC TYPE Button (Radio Mode) Pressing this button once will turn on the Music Type mode for 5 seconds. Pressing the Music Type button or turning the TUNE control knob within 5 seconds will allow the program format type to be selected. Many radio stations do not currently broadcast Music Type informa- tion.
Page 163 If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items: NOTE: Use Tune Control Knob to scroll through the entries, and push Audio/Select button to select an entry...
Page 164 164 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button will allow user to set the clock. Turn TUNE control knob to adjust the hours then press and turn the TUNE control knob to adjust the minutes. Press the TUNE control knob again to save changes.
Page 165 Aspect Ratio — If Equipped Selecting this item will allow the user to choose between wide screen, pan scan, and letter box. AutoPlay — If Equipped When this is set to ON and a DVD video is inserted, it will bypass the DVD menu screen and automatically play the movie.
Page 166: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
166 UNDERSTANDING YOUR INSTRUMENT PANEL DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - (DISC MODE for CD and MP3/WMA Audio Play, DVD-VIDEO) The radio DVD player and many DVD discs are coded by geographic region.
Page 167 Eject Button — Ejecting Compact Disc(s) Press the eject button and the push-button with the corresponding number (1-6) where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
Page 168: Notes On Playing Mp3/Wma Files
168 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files The radio can play MP3/WMA files, however, acceptable MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the following restrictions. Supported Media (Disc Types) The MP3/WMA file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3,WMA, DVD Video, DVD-R, DVD-RW, DVD+R, DVD+RW, and CDDA+MP3.
Page 169 When using the MP3/WMA encoder to compress audio data to an MP3/WMA file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit rates (VBR) are also supported. The majority of MP3/WMA files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.
Page 170: List Button (Disc Mode For Mp3/Wma Play)
170 UNDERSTANDING YOUR INSTRUMENT PANEL LIST Button (DISC Mode for MP3/WMA Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE control knob. Selecting a folder by pressing the TUNE control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files).
Page 171 PSCAN Button (Auxiliary Mode) No function. TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will be displayed for 5 seconds. RW/FF (Auxiliary Mode) No function. SET Button (Auxiliary Mode) No function.
Page 172: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)
172 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK) NOTE: The radio sales code is located on the lower right side of your radio faceplate. RES Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 173 SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station, in either AM or FM frequen- cies, pausing for 5 seconds at each listenable station before continuing to the next. To stop the search, press SCAN a second time.
Page 174 174 UNDERSTANDING YOUR INSTRUMENT PANEL Setting the Tone, Balance, and Fade Press the rotary TUNE control knob and BASS will display. Turn the TUNE control knob to the right or left to increase or decrease the Bass tones. Press the rotary TUNE control knob a second time and MID will display.
Page 175 News Nostalgia Oldies Personality Public Rhythm and Blues Religious Music Rel Musc Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Soft R&B Sports Talk Top 40 Weather By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name.
Page 176: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play
176 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 177 CAUTION! • This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel away and jam the player mechanism. •...
Page 178: Notes On Playing Mp3 Files
178 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. AM or FM Button Switches the Radio to the Radio mode.
Page 179 • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 3-character extension) • Level 2: 31 (including a separator 3-character extension) Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files).
Page 180: List Button (Cd Mode For Mp3 Play)
180 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files.
Page 181: Sales Code Rer - Am/Fm/Cd/Dvd
Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 182: Operating Instructions - Satellite Radio
182 UNDERSTANDING YOUR INSTRUMENT PANEL This radio has a hard drive. CD’s can be ripped to the hard drive, and the map data comes loaded on the hard drive. Refer to your “Navigation User’s Manual” for detailed operating instructions. Operating Instructions — Satellite Radio Refer to your “Navigation User’s Manual”...
Page 183: Satellite Radio - If Equipped
NOTE: When you are traveling and enter a new time zone, the cluck must be reset manually for the new zone. Changing Daylight Savings Time 1. Highlight the box next to “Time” and press ENTER. 2. Select Daylight Savings when Daylight Savings Time is in effect or Select Standard if Daylight Savings Time is not being observed.
Page 184: Selecting Satellite Mode (Rsc Radios)
184 UNDERSTANDING YOUR INSTRUMENT PANEL ESN/SID Access With RSC Radios With the ignition switch in the ON/RUN or ACCESSORY position and the radio ON, press the SETUP button and scroll using the TUNE control knob until Sirius ID is selected. Press the TUNE control knob and the Sirius ID number will be displayed.
Page 185 remain tuned to the new channel until you make another selection. Holding either button will bypass channels without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next channel, pausing for 8 seconds before continuing to the next.
Page 186: Operating Instructions - Hands Free Phone (If Equipped)
186 UNDERSTANDING YOUR INSTRUMENT PANEL SET Button — To Set the Push-Button Memory When you are receiving a channel that you wish to commit to push-button memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel and press and release that button.
Page 187: Video Entertainment System - If Equipped
VIDEO ENTERTAINMENT SYSTEM — IF EQUIPPED The optional VES™ (Video Entertainment System) in- cludes the following components for rear seat entertain- ment: • A diagonal seven-inch liquid crystal display (LCD) screen integrated into the center console armrest. The screen features brightness control for optimum day- time and nighttime viewing.
Page 188: Radio Operation And Cellular Phones
188 UNDERSTANDING YOUR INSTRUMENT PANEL • Two wireless infrared headsets allow rear seat passen- gers to listen to the same or individual audio sources. • Audio/Video RCA Jacks (AUX Jacks) on the rear of the center console enable the monitor to display video directly from a video camera, connect video games for display on the screen or play music directly from an MP3 player.
Page 189: Radio Operation
The button located in the center of the right hand control will switch modes to Radio or CD. The left hand control is a rocker type switch with a push button in the center. The function of the left hand control is different depending on which mode you are in.
Page 190: Climate Controls
190 UNDERSTANDING YOUR INSTRUMENT PANEL 7. Do not store the disc where temperatures may become too high. CLIMATE CONTROLS The Climate Control System allows you to balance the temperature, amount, and direction of air circulating throughout the vehicle. The controls are located on the instrument panel, below the radio.
Page 191 The instrument panel features four airflow registers. Two registers are located on the outer ends of the instrument panel and two are located in the center of the instrument panel. These registers can be fully closed to partially block airflow, and they can be adjusted to direct airflow where the occupant desires.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes.
Page 193 This dehumidifies the air to help dry the windshield. To improve fuel economy, use these modes only when necessary. Recirculation Control Use this button to choose be- tween outside air intake or recirculation of the air inside the vehicle. A lamp will illu- minate when you are in recir- culate mode.
Page 194: Automatic Temperature Control (Atc)- If Equipped
194 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Operation Use this button to engage the Air Conditioning. A lamp will illuminate when the Air Con- ditioning System is engaged NOTE: The air conditioning compressor will not en- gage until the engine has been running for about 10 seconds.
Page 195 Operation of the system is quite simple. 1. Turn the Mode Control knob (on the right) and the Blower Control knob (on the left) to AUTO. NOTE: The AUTO position performs best for front seat occupants only. 2. Dial in the temperature you would like the system to maintain by rotating the Temperature Control knob.
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL Air conditioning in this system is automatic. Pressing the Air Conditioning Control button while in AUTO mode will cause the LED in the control button to flash three times and then turn off. This indicates that the system is in AUTO mode and request- ing the air conditioning is not necessary.
Page 197 • In cold weather, use of the Recirculation mode may lead to excessive window fogging. The Recirculation mode is not allowed in the Mix and Defrost modes to improve window clearing operation. Recirculation will be disabled automatically if these modes are selected.
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL Auto Climate Controls Chart...
Page 199: Operating Tips
The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control knob (on the right) to one of the following positions. Panel Mode Air is directed through the outlets in the instrument panel. These outlets can be adjusted to direct air flow. Bi-Level Mode Air is directed through the panel and floor outlets.
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Vacation Storage Anytime you store your vehicle, or keep it out of service (i.e. vacation) for two weeks or more, run the air condi- tioning system at idle for about five minutes in the fresh air and high blower setting.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 201 Control Setting Suggestions for Various Weather Conditions...
Page 202: Electric Rear Window Defroster
202 UNDERSTANDING YOUR INSTRUMENT PANEL Electric Rear Window Defroster Press this button, located on the Blower Control knob, to turn on the rear window defroster and the heated side mirrors — if equipped. A light in the button will illuminate to indicate the rear window defroster is ON.
Page 203: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....207 Automatic Transaxle ....207 Normal Starting .
Page 204 204 STARTING AND OPERATING Electronic Brake Control System – ABS/TCS/BAS/ESP ....221 Anti-Lock Brake System (ABS) — If Equipped ......221 Traction Control System (TCS) —...
Page 205 General Information ....248 Tire Chains ......248 Snow Tires .
Page 206 206 STARTING AND OPERATING Loading ......260 Trailer Towing ......261 Common Towing Definitions .
Page 207: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Make sure all occupants have securely fastened their seat belts. WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
Page 208: Tip Start Feature - Automatic Transaxle Only
208 STARTING AND OPERATING start within 15 seconds, turn the ignition switch to the “OFF” position, wait 10 to 15 seconds, then repeat the normal starting procedure. WARNING! Do not attempt to push or tow your vehicle to get it started.
Page 209: After Starting
engine is flooded. Leave the ignition key in the ON position, release the accelerator pedal and repeat the “NORMAL STARTING” procedure. WARNING! Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start the vehicle.
Page 210 210 STARTING AND OPERATING REMOTE START BUTTON To exit the Remote Start mode , allow the engine to run the cycle or depress the unlock button to disarm the Vehicle Theft Security Alarm and within one minute insert the key into the ignition and turn the ignition to the RUN position.
Page 211: Automatic Transaxle
AUTOMATIC TRANSAXLE Automatic Transaxle Shifter CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. STARTING AND OPERATING 211 • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 212: Brake/Transaxle Interlock System
212 STARTING AND OPERATING Brake/Transaxle Interlock System This system prevents you from moving the gear shift out of Park and into any gear unless the brake pedal is pressed. This system is active only while the ignition switch is in the ON or ACC positions. Always depress the brake pedal first, before moving the gear selector out of PARK.
Page 213 • Stop the vehicle and shift into Park (P). • Turn the key to OFF then restart the engine. • Shift into the desired range and resume driving. NOTE: Even if the transaxle can be reset, it is recom- mended that you visit a dealer at your earliest possible convenience.
Page 214: Autostick - If Equipped
214 STARTING AND OPERATING “3” Drive This range eliminates shifts into Overdrive. The transaxle will operate normally in First, Second and Third while in this range. The “3” position should also be used when descending steep grades to prevent brake system dis- tress.
Page 215: Autostick Operation
AutoStick Operation By placing the selector lever one shift level below the D position, it can be moved from side to side. This allows the driver to select a higher or lower range of gears. Moving the selector lever to the Left (-) triggers a downshift and to the Right (+) an upshift.
Page 216: Parking Brake
216 STARTING AND OPERATING • If the system detects a problem it will disable the AutoStick mode and the transaxle will return to the automatic mode until the problem is corrected. PARKING BRAKE When the parking brake is applied with the ignition on, the Brake Light in the instrument cluster will come on.
Page 217: Brake System
NOTE: When parking on a hill, it is important to set the parking brake before placing the gear selector in Park, otherwise the load on the automatic transaxle locking mechanism may make it difficult to move the selector out of Park. As an added precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on a uphill grade.
Page 218: Anti-Lock Brake System (Abs) - If Equipped
218 STARTING AND OPERATING If either of the two hydraulic systems lose normal capa- bility, the remaining system will still function with some loss of overall braking effectiveness. This will be evident by increased pedal travel during application and greater pedal force required to slow or stop.
Page 219 WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 220 220 STARTING AND OPERATING ABS is activated during braking under certain road or stopping conditions. ABS-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose debris, or panic stops. You also may experience the following when the brake system goes into Anti-lock: •...
Page 221: Electronic Brake Control System - Abs/Tcs/Bas/Esp
ELECTRONIC BRAKE CONTROL SYSTEM – ABS/TCS/BAS/ESP Your vehicle may be equipped with an optional ad- vanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS) and Electronic Stability Program (ESP). All systems work together to enhance vehicle stability and control in various driving conditions and are commonly referred to as ESP.
Page 222: Electronic Stability Program (Esp) - If Equipped
222 STARTING AND OPERATING WARNING! • BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 223 WARNING! • Electronic Stability Program (ESP) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning.
Page 224 224 STARTING AND OPERATING WARNING! In the Partial ESP mode, the engine torque reduction and stability features are desensitized. Therefore, the enhanced vehicle stability offered by ESP is unavailable. NOTE: To improve the vehicle’s traction when driving with snow chains, or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off”...
Page 225: Power Steering
POWER STEERING The standard power steering system will give you good vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical steering capability if power assist is lost. If for some reason the power assist is interrupted, it will still be possible to steer your vehicle.
Page 226: Driving On Slippery Surfaces
226 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip- pery surfaces may cause the front wheels to pull errati- cally to the right or left. This phenomenon occurs when there is a difference in the surface traction under the front (driving) wheels.
Page 227: Tire Safety Information
TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. STARTING AND OPERATING 227 • European Metric tire sizing is based on European design standards.
Page 228 228 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 229 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions (i.e.
Page 230: Tire Identification Number (Tin)
230 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 231: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 231 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the:...
Page 232 232 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 233 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. NOTE: The following table shows examples on how to calculate total load, cargo/luggage, and towing capaci- ties of your vehicle with varying seating configurations STARTING AND OPERATING 233...
Page 234 234 STARTING AND OPERATING...
Page 235: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 236: Tire Inflation Pressures
236 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 237 CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 238: Radial-Ply Tires
238 STARTING AND OPERATING WARNING! High speed driving with your vehicle under maxi- mum load is dangerous. The added strain on your tires could cause them to fail. You could have a serious accident. Don’t drive a vehicle loaded to the maximum capacity at continuous speeds above 75 mph (120 km/h).
Page 239: Limited Use Spare - If Equipped
CAUTION! Prolonged use of limited use spare, or an incorrect tire size on either front wheel, may damage transaxle differential and result in loss of vehicle mobility. Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare.
Page 240: Tire Spinning
240 STARTING AND OPERATING WARNING! Prolonged use of limited use spare, or incorrect tire size of front wheel, may damage the transaxle dif- ferential and result in loss of vehicle mobility and could result in loss of vehicle control. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) for more than 30 seconds continuously.
Page 241: Life Of Tire
Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure.
Page 242: Alignment And Balance
242 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Page 243: Tire Pressure Monitoring System (Tpms) - If Equipped
TIRE PRESSURE MONITORING SYSTEM (TPMS) — IF EQUIPPED Base Tire Pressure Monitoring System (TPMS) Operation – If Equipped This is the Tire Pressure Monitoring System warn- ing indicator located in the instrument cluster. • The Tire Pressure Monitoring System (TPMS) will warn the driver of a low tire pressure based on the vehicle recommended cold placard pressure.
Page 244: Premium System - If Equipped
244 STARTING AND OPERATING sufficiently low enough to turn ON the “Tire Pressure Monitoring Light”. Driving the vehicle may cause the tire pressure to rise to approximately 30 psi (207 kPa), but the “Tire Pressure Monitoring Light” will still be ON. In this situation, the “Tire Pressure Monitoring Light”...
Page 245 Low Tire Pressure Display NOTE: A low spare tire will not cause the Tire Pressure Monitoring Telltale Lamp to illuminate or the chime to sound. Should a low tire condition occur on any of the four active road tire(s), you should stop as soon as possible, and inflate the low tire(s) that is flashing on the graphic display to the vehicle’s recommended cold placard pres- sure value.
Page 246 246 STARTING AND OPERATING Check TPM System Display If the ignition key is cycled, this sequence will repeat, providing the system fault still exists. If the system fault no longer exists, the Tire Pressure Monitoring Telltale Light will no longer flash, and the CHECK TPM SYS- TEM text message will no longer display.
Page 247 CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
Page 248: General Information
248 STARTING AND OPERATING General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired op- eration.
Page 249: Tire Rotation Recommendations
Snow tires generally have lower speed ratings than what was originally equipped with your vehicle and should not be operated at sustained speeds over 75 mph (120 km/h). Tire Rotation Recommendations Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving and braking functions.
Page 250: Fuel Requirements
(with the ap- propriate octane rating for your engine) before consider- ing service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) which...
Page 251: Reformulated Gasoline
Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline”. Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality. The manufacturer supports the use of reformulated gaso- lines.
Page 252: Mmt In Gasoline
252 STARTING AND OPERATING MMT In Gasoline MMT is a manganese containing metallic additive that is blended into some gasoline to increase the octane num- ber. Gasolines blended with MMT offer no performance advantage beyond gasolines of the same octane number without MMT.
Page 253: Carbon Monoxide Warnings
Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not the responsibility of the manufacturer. NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly.
Page 254: Ethanol Fuel (E-85)
254 STARTING AND OPERATING CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
Page 255: Selection Of Engine Oil For Flexible Fuel
Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requirements are the same. Refer to “Engine Oil Selection in the “Maintenance Procedures” section of this manual for the proper quality and viscosity engine oil.
Page 256: Adding Fuel
256 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle.
Page 257: Loose Fuel Filler Cap Message
CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. CAUTION! A poorly fitting gas cap may cause the Malfunction Indicator Light to turn on.
Page 258: Vehicle Loading
258 STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you hear one click. This is an indication that cap is properly tightened. If the gas cap is not tighten properly, the Malfunction Indicator Light will come on. Be sure the gas cap is tightened every time the vehicle is refueled.
Page 259: Gross Vehicle Weight Rating (Gvwr)
• Gross Axle Weight Rating (GAWR) rear • Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read the Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.
Page 260: Loading
260 STARTING AND OPERATING Overloading can cause potential safety hazards and shorten useful service life. Heavier axles or suspension components do not necessarily increase the vehicle’s GVWR. Loading To load your vehicle properly, first figure out its empty weight, axle by axle and side by side. Store heavier items down low and be sure you distribute their weight as evenly as possible.
Page 261: Trailer Towing
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible.
Page 262 262 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) The gross combination weight rating (GCWR) is the total permissible weight of your vehicle and trailer when weighed in combination. (Note that GCWR ratings in- clude a 150 lbs (68 kg) allowance for the presence of a driver).
Page 263: Trailer Hitch Classification
Section in this manual. Enclosed trailers or open utility trailers with front shields/guards are not recommended for use with 2.4L or 2.7L engine with automatic transmission. Please see the website, http://www-5.chrysler.com/searchapp/ui.jsp or your dealer for additional information. STARTING AND OPERATING 263...
Page 264: Trailer And Tongue Weight
264 STARTING AND OPERATING CAUTION! Towing a trailer with a larger than recommended frontal area could cause the engine to overheat or cause severe engine damage under extreme condi- tions. Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer.
Page 265: Towing Requirements
must be considered as part of the total load on your vehicle. Refer to the Tire and Loading Information plac- ard in the Tire Safety Information Section of this manual for the maximum combined weight of occupants and cargo for your vehicle. CAUTION! Incorrect tongue weight could result in increased yaw or vehicle instability.
Page 266 266 STARTING AND OPERATING WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer and will not shift during travel. When trailering cargo that is not fully secured, dynamic load shifts can occur that may be difficult for the driver to control.
Page 267 − Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to the Tires–General Information section of this manual on Tire Pressures for proper tire inflation procedures. − Also, check the trailer tires for proper tire inflation pressures before trailer usage.
Page 268 268 STARTING AND OPERATING WARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance.
Page 269: Towing Tips
7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. Make sure all trailer and vehicle lights are working properly — including hazard flashers. STARTING AND OPERATING 269 Towing Tips —...
Page 270: Recreational Towing (Behind Motorhome, Etc.)
270 STARTING AND OPERATING − When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until you can get back to cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency.
Page 271: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....272 If Your Engine Overheats ....272 Engine Oil Overheating —...
Page 272: Hazard Warning Flasher
272 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, below the radio. Depress the switch and both cluster indicators and all front and rear directional signals will flash. Depress the switch again to turn Hazard Warning Flashers off.
Page 273: Engine Oil Overheating - 2.4L Engine Only (If Equipped)
NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioner is on, turn it off. The air conditioning system adds heat to the engine cooling system and turning off the A/C removes this heat.
Page 274: Jacking And Tire Changing
274 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
Page 275: Preparations For Jacking
Preparations For Jacking Park the vehicle on a firm level surface, avoid ice or slippery areas, set the parking brake and place the gear selector in PARK (automatic transaxle) or REVERSE (manual transaxle). Turn OFF the ignition. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 276: Jacking Instructions
276 WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly.
Page 277 WHAT TO DO IN EMERGENCIES 277 Jacking Locations...
Page 278 278 WHAT TO DO IN EMERGENCIES CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated in step 3. 3. There are two front jacking locations and two rear jacking locations on each side of the body. The front locations are outlined by two triangular cutouts, the rear ones by two rectangular cutouts.
Page 279 WARNING! To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp edges. NOTE: The wheel cover is held on the wheel by the wheel nuts. When reinstalling original wheel, properly align the wheel cover to the valve stem, place the wheel cover onto the wheel, then install the wheel nuts.
Page 280: Jump-Starting Procedures Due To A Low Battery
280 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW BATTERY Jump-starting remote battery terminals are located under the hood. The battery is stored between the left front head lamp assembly and the left front wheel splash shield. Access is through the splash shield.
Page 281 1. Wear eye protection and remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact. 2. When boosting from a battery in another vehicle, park that vehicle within booster cable reach but without letting the vehicles touch.
Page 282: Freeing A Stuck Vehicle
282 WHAT TO DO IN EMERGENCIES 6. If the vehicle is equipped with Sentry Key Immobi- lizer, turn the ignition switch to the ON position for 3 seconds before moving the ignition switch to the START position. 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, then start the engine in the vehicle with the discharged battery.
Page 283: Towing A Disabled Vehicle
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause axle, tire damage or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck.
Page 284: Without The Ignition Key
284 WHAT TO DO IN EMERGENCIES If it is necessary to use the accessories while being towed (wipers, defrosters, etc.), the key must be in the ON position, not the ACCESSORY position. Make certain the transaxle remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towed with the ignition in the LOCK position.
Page 285: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Engine Compartment ....287 2.7L Engine Compartment ....288 3.5L Engine Compartment .
Page 286 286 MAINTAINING YOUR VEHICLE Exhaust System ..... . 304 Cooling System ..... . . 305 Hoses And Vacuum/Vapor Harnesses .
Page 287: 2.4L Engine Compartment
MAINTAINING YOUR VEHICLE 287 2.4L ENGINE COMPARTMENT 2.4L Engine...
Page 288: 2.7L Engine Compartment
288 MAINTAINING YOUR VEHICLE 2.7L ENGINE COMPARTMENT 2.7L Engine...
Page 289: L Engine Compartment
MAINTAINING YOUR VEHICLE 289 3.5L ENGINE COMPARTMENT 3.5L Engine...
Page 290: Onboard Diagnostic System - Obd Ii
290 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 291: Emissions Inspection And Maintenance Programs
might indicate a damaged cap. If the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off. EMISSIONS INSPECTION AND MAINTENANCE PROGRAMS In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
Page 292: Replacement Parts
292 MAINTAINING YOUR VEHICLE b. The MIL will not flash at all and will remain fully illuminated until you turn off the ignition key or start the engine. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station.
Page 293: Maintenance Procedures
WARNING! You can be badly injured working on or around a motor vehicle. Only do service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 294 294 MAINTAINING YOUR VEHICLE Engine Oil Dipstick — Gasoline Engines Checking the oil while the vehicle is on level ground and only when the engine is hot, will improve the accuracy of the oil level readings. Maintain the oil level between the range markings on the dipstick.
Page 295 • Trailer towing. • Taxi, Police or delivery service (commercial service). • Off-Road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow schedule “B—All Engines”...
Page 296 296 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) SAE 5W-20 engine oil for 2.4L and 2.7L engines, is recommended for all operating temperatures. 5W-20 Oil Viscosity Chart SAE 10W-30 engine oil for 3.5L engines, is recom- mended for all operating temperatures. 10W-30 Oil Viscosity Chart These engine oils are designed to improve low tempera- ture starting and vehicle fuel economy.
Page 297: Spark Plugs
Synthetic Engine Oils There are a number of engine oils being promoted as either synthetic or semi-synthetic. If you chose to use such a product, use only those oils that are American Petroleum Institute (API) Certified and have the recom- mended SAE viscosity grade.
Page 298: Catalytic Converter
298 MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
Page 299: Crankcase Emission Control System
• Do not idle the engine with any ignition coil connec- tors disconnected for prolonged periods. Crankcase Emission Control System Proper operation of this system depends on freedom from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may accumulate deposits.
Page 300: Maintenance-Free Battery
300 MAINTAINING YOUR VEHICLE Maintenance-Free Battery You will never have to add water, nor is periodic main- tenance required. NOTE: The battery is stored in a compartment behind the left front fender and is accessible without removing the tire and wheel. Remote battery terminals are located in the engine compartment for jump starting.
Page 301: Air Conditioner Maintenance
CAUTION! It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked positive (+) and negative (-) and identified on the battery case. Cable clamps should be tight on the terminal posts and free of corrosion.
Page 302: Power Steering - Fluid Check
302 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 303: Body Lubrication
Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, liftgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 304: Windshield Washer Reservoir
304 MAINTAINING YOUR VEHICLE 3. Install the new blade assembly onto the wiper arm tip until it locks in place. NOTE: Always refer to the wiper blade packaging for specific installation instructions. Many wiper blade re- placements fit multiple vehicles. Windshield Washer Reservoir The washer fluid reservoir is located engine compart- ment and should be checked for fluid level at regular...
Page 305: Cooling System
Cooling System WARNING! • When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the OFF position. The fan is temperature controlled and can start at any time the ignition switch is in the ON position. •...
Page 306 306 MAINTAINING YOUR VEHICLE CAUTION! Mixing of coolants other than specified HOAT en- gine coolants, may result in engine damage and may decrease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 307 Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
Page 308 308 MAINTAINING YOUR VEHICLE ground. If ingested by a child, contact a physician immediately. Clean up any ground spills immediately. Coolant Level 4 Cylinder Engines — the coolant bottle provides a quick visual method for determining that the coolant level is adequate.
Page 309: Hoses And Vacuum/Vapor Harnesses
• Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. •...
Page 310: Brake System
310 MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Suggested service intervals can be found in the Mainte- nance Section. WARNING! Riding the brakes can lead to brake failure and possibly an accident.
Page 311 WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any signs of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Brake Master Cylinder The fluid level in the master cylinder should be checked when performing under hood services, or immediately if the brake system warning lamp is on.
Page 312: Automatic Transaxle
312 MAINTAINING YOUR VEHICLE Automatic Transaxle The automatic transaxle and differential assembly are contained within a single housing. All automatic transaxles (with the exception of the trans- axle with the 3.5L engine, which has no dipstick and is dealer service only) are equipped with a conventional filler tube and dipstick.
Page 313: Appearance Care And Protection From Corrosion
If the fluid level indicates low, add sufficient fluid to bring to the proper level. CAUTION! Do not overfill. Dirt and water in the transaxle can cause serious damage. To prevent dirt and water from entering the transaxle after checking or replen- ishing fluid, make certain that the dipstick cap is re-seated properly.
Page 314 314 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, use Mopar Super Kleen Bug and Tar Remover to remove.
Page 315 • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 316 316 MAINTAINING YOUR VEHICLE YES Essentials Fabric Cleaning Procedure – If Equipped YES Essentials seats may be cleaned in the following manner: • Remove as much of the stain as possible by blotting with a clean, dry towel. • Blot any remaining stain with a clean, damp towel. •...
Page 317: Cleaning The Center Console Cup Holders
Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.
Page 318: Fuses/Totally Integrated Power Module (Tipm)
318 MAINTAINING YOUR VEHICLE FUSES/TOTALLY INTEGRATED POWER MODULE (TIPM) A Totally Integrated Power Module is located in the engine compartment near the air cleaner assembly. This center contains cartridge fuses and mini fuses. A label that identifies each component may be printed on the inside of the cover.
Page 319 Cavity Cartridge Mini Description Fuse Fuse 20 Amp CCN Power Locks Yellow 15 Amp Power Outlet Lt Blue 20 Amp Ign Run/Acc Inverter Yellow 20 Amp Pwr run/Acc Outlet Yellow 10 Amp IOD CCN/ Interior Lighting 40 Amp RAD Fan Relay Bat- Green tery Feed 15 Amp...
Page 320 320 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini Fuse Fuse 20 Amp Heated Seats Yellow 10 Amp Headlamp Washer Relay Control 30 Amp ENG ASD Control Pink Feed 1 10 Amp ABS MOD/J1962 Conn/PCM 30 Amp ABS Valve Feed Pink 40 Amp ABS Pump Feed Green 30 Amp...
Page 321: Vehicle Storage
VEHICLE STORAGE If you will not be using your vehicle for more than 21 days you may want to take steps to preserve your battery. You may: • Disengage the mini fuse in the Power Distribution Center labeled IOD (Ignition Off-Draw). •...
Page 322: Bulb Replacement
322 MAINTAINING YOUR VEHICLE BULB REPLACEMENT Head Lamp Bulb Replacement 1. Open the hood and remove the two head lamp mount- ing screws. Removing Head Lamp For Bulb Replacement 2. Remove the push-in fasteners by prying under the head of the fasteners with a flat bladed tool. 3.
Page 323: Fog Lamps
CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. 6. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. 7. Reinsert the bulb and socket assembly and rotate clockwise ⁄...
Page 324: Tail Lamps, Rear Turn Signals And Backup Lamps - Replacement
324 MAINTAINING YOUR VEHICLE Tail Lamps, Rear Turn Signals And Backup Lamps — Replacement The tail lamps are a two piece design. The turn signal, brake and tail lamps are located in the rear corner body panel housing. The back up and tail lamps are located in the trunk lid housing.
Page 325 2. Remove the two plastic wing nuts from the tail lamp housing. Location Plastic Wing Nuts 3. Grasp the tail lamp and pull firmly outward pushing gently on the studs from inside to disengage the lamp housing. 4. Twist and remove socket from lamp. 5.
Page 326: License Plate Lamp - Rear
326 MAINTAINING YOUR VEHICLE License Plate Lamp — Rear 1. Remove two retaining screws holding the lamp lens in place. Location and Removal of Rear License Lamp Lens 2. Gently pry the lens loose. 3. Pull bulb from socket, replace and reattach the lamp lens with the two retaining screws.
Page 327: Fluids And Capacities
FLUIDS AND CAPACITIES Fuel (approximate) 2.4L, 2.7L and 3.5 Liter Engine Engine Oil with Filter 2.4 Liter Engine (SAE 5W-20, API Certified) 2.7 Liter Engine (SAE 5W-20, API Certified) 3.5 Liter Engine (SAE 10W-30, API Certified) Cooling System * 2.4 Liter Engine (Mopar Antifreeze/Coolant 5 Year/100,000 Mile For- mula) or equivalent.
Page 328: Fluids, Lubricants, And Genuine Parts
328 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Engine Coolant Engine Oil (2.4 & 2.7 Liter) Engine Oil (3.5 Liter) Oil Filter (2.4 Liter) Oil Filter (2.7 & 3.5 Liter) Spark Plugs Fuel Selection (2.4 & 2.7 Liter) Fuel Selection (3.5 Liter) Fluids, Lubricants, and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid...
Page 329 Chassis Component Automatic Transmission Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3 and SAE J1703 should be used. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. Mopar ATF+4 Automatic Transmission Fluid.
Page 331 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..332 Maintenance Schedules ....332 Schedule “B” ......335 Schedule “A”...
Page 332: Emission Control System Maintenance
332 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 333 NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual. NOTE: If ANY of these apply to you then change your coolant every 102,000 miles (170 000 km) or 60 months, whichever comes first and follow schedule “B”...
Page 334 334 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake/ clutch master cylinder, and manual transaxle and add as needed. • Check all lights and all other electrical items for correct operation. At Each Oil Change • Change the engine oil filter. •...
Page 335: Schedule "B" 335
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 336 336 SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Inspect engine air cleaner filter, replace if neces- sary. Rotate tires. Check spare tire for proper pressure and correct stowage. 3,000 6,000 9,000 (5 000) (10 000)
Page 337 Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace the air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.4L Engine 18,000 21,000 24,000 (30 000)
Page 338 338 SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Inspect engine air cleaner filter, replace if neces- sary. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. 33,000 36,000 39, 000...
Page 339 Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Change Automatic Transaxle Fluid and Filter. Replace Spark Plugs: 2.4L Engine Flush and replace engine coolant at 60 months, or 102,000 miles (170 000 km) whichever comes first.
Page 340 340 SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Inspect engine air cleaner filter, replace if neces- sary. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. 63,000 66,000 69,000...
Page 341 Miles (Kilometers ) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.4L Engine 78,000 81,000 84,000...
Page 342 342 SCHEDULE “B” Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Replace Spark Plugs: 2.7L and 3.5L Engines Flush and replace engine coolant if not done at 60 months.
Page 343 Miles (Kilometers) Change engine oil and oil filter, or at 3 months, whichever comes first. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Change Automatic Transaxle Fluid and Filter. Replace Spark Plugs: 2.4L Engine Replace the accessory drive belt every 120,000 miles (200 000 km).
Page 344: Schedule "A
344 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and oil filter. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.4L Engine 6,000 12,000 18,000 (10 000) (20 000)
Page 345 Miles (Kilometers) [Months] Change engine oil and oil filter. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (170 000 km). Replace Spark Plugs: 2.4L Engine 36,000 42,000...
Page 346 346 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and oil filter. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Replace Spark Plugs: 2.4L Engine 66,000 72,000 78,000 (110 000) (120 000) (130 000) [66]...
Page 347 Miles (Kilometers) [Months] Change engine oil and oil filter. Replace engine air cleaner filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Inspect brake linings. Change Automatic Transaxle Fluid and Filter. Flush and replace engine coolant, 102,000 miles (170 000 km) if not done at 60,000 miles Replace Spark Plugs: 2.4L Engine Replace Spark Plugs: 2.7L and 3.5L Engines...
Page 348 348 SCHEDULE “A” Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment.
Page 349: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......350 Prepare For The Appointment .
Page 350: Suggestions For Obtaining Service For Your Vehicle
We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 351 • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance. • If your dealership is unable to resolve the concern, you may contact the Manufacturer’s Customer Center. Any communication to the Manufacturer’s Customer Center should include the following information: •...
Page 352: Warranty Information (U.s. Vehicles Only)
352 IF YOU NEED CONSUMER ASSISTANCE Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires. The manufacturer stands be- hind only the manufacturer’s Service Contracts.
Page 353: Reporting Safety Defects
REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect, which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 354: Department Of Transportation Uniform Tire Quality Grades
• Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 355: Treadwear
Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled con- ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire graded 100.
Page 356 356 IF YOU NEED CONSUMER ASSISTANCE WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under inflation, or excessive load- ing, either separately or in combination, can cause heat buildup and possible tire failure.
Page 357 INDEX...
Page 358 358 INDEX ABS (Anti-Lock Brake System) ... . . 218 Adding Engine Coolant (Antifreeze) ..306 Adding Fuel ......256 Adding Washer Fluid .
Page 359 Keyless Transmitter Replacement (RKE) ..20 Location ......300 Body Mechanism Lubrication .
Page 360 360 INDEX Coin Holder ......128 Compact Disc (CD) Maintenance ... 189 Compact Spare Tire .
Page 361 Electrical Power Outlets ....124,125 Electronic Speed Control (Cruise Control) ..113 Electronic Stability Program (ESP) ..222 Electronic Vehicle Information Center (EVIC) .
Page 362 362 INDEX Maintenance ......255 Replacement Parts ....255 Starting .
Page 363 General Information ....14,95,248 General Maintenance ....293 Glass Cleaning .
Page 364 364 INDEX Jump Starting ......280 Key, Programming ..... . . 13 Key, Replacement .
Page 365 Theft Alarm (Security Alarm) ... . 140 Traction Control ..... . 222 Turn Signal .
Page 366 366 INDEX Octane Rating, Gasoline (Fuel) ... . . 250 Odometer ......142 Trip .
Page 367 Programming Transmitters (Remote Keyless Entry) ....20,115,119 Radial Ply Tires ......238 Radio Broadcast Signals .
Page 368 368 INDEX Child Restraint ..... . 54,61 Extender ......40 Front Seat .
Page 369 Steering Wheel Mounted Sound System Controls ......188 Storage ......321 Storage, Vehicle .
Page 370 370 INDEX Spare Tire ......274 Spinning ......240 Tread Wear Indicators .
Page 371 Vacuum/Vapor Harnesses ....309 Vanity Mirrors ......73 Variance, Compass .
Page 372 NOTES...
Page 373 NOTES...
Page 374 NOTES...
Page 375 NOTES...
Page 376 NOTES...

This manual is also suitable for:

Sebring sedan 2007

Chrysler 2007 Sebring Sedan Instruction Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2007 Sebring Sedan

Summary of Contents for Chrysler 2007 Sebring Sedan