Chrysler 2007 Aspen Owner's Manual

page of 472

/ 472
Contents
Table of Contents
Bookmarks

Table of Contents

Quick Links

Download this manual

SECTION

INTRODUCTION

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

INSTRUMENT PANEL AND CONTROLS

STARTING AND OPERATING

WHAT TO DO IN EMERGENCIES

MAINTAINING YOUR VEHICLE

MAINTENANCE SCHEDULES

IF YOU NEED CONSUMER ASSISTANCE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 449

INDEX

TABLE OF CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 345

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

PAGE

Table of Contents

Chapters

Table of Contents

Summary of Contents for Chrysler 2007 Aspen

Page 1: Introduction
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3: Table Of Contents
CONTENTS Introduction ......4 Roll Over Warning ..... 4 How To Use This Manual .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: How To Use This Manual
Failure to use driver and passenger seat belts provided is a major cause of severe or fatal injury. In fact, the U.S. government notes that the universal use of existing seat belts could cut the highway death toll by 10,000 or more each year, and could reduce disabling injuries by 2 million annually.
Page 6 6 INTRODUCTION...
Page 7: Warnings And Cautions
INTRODUCTION 7 WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 8: Vehicle Modifications / Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Ignition Key Removal ....12 Locking Doors With The Key .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information ....22 Programming Additional Transmitters ..23 Battery Replacement .
Page 11 Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags ...51 Event Data Recorder (EDR) ....60 Child Restraint ......62 Engine Break-In Recommendations .
Page 12: A Word About Your Keys
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the key code numbers for your vehicle locks. These numbers can be used to order duplicate keys from your dealer. Ask your dealer for these numbers and keep them in a safe place.
Page 13: Locking Doors With The Key
in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as described. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 14: Ignition Accessory Delay Feature
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE inserted or withdrawn only in the LOCK position. Push in on the key in the ignition lock cylinder to rotate to the LOCK position. Ignition Switch Positions WARNING! The key cannot be turned to LOCK until the selector is in the PARK position.
Page 15: Sentry Key - If Equipped
For vehicles equipped with the Electronic Vehicle Infor- mation Center (EVIC), the power window switches, radio, hands–free system (if equipped), and power out- lets will remain active for up to 10 minutes after the ignition switch is turned off. Opening either front door will cancel this feature.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the Vehicle Security Alarm Indicator Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle ser- viced as soon as possible.
Page 17: General Information
4. Insert a blank Sentry Key into the ignition switch and turn the ignition switch ON within 60 seconds. After 10 seconds a single chime will sound and the Vehicle Theft Alarm Indicator Light will stop flashing, turn on again for 3 seconds, and then turn off.
Page 18: To Set The Alarm
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set the Alarm: The alarm will set when you use the power door locks or use the Keyless Entry transmitter to lock the doors. After all the doors are locked and closed the security light in the instrument cluster will flash rapidly to signal that the system is arming.
Page 19: Illuminated Entry
ILLUMINATED ENTRY Vehicles Equipped With Power Door Locks All interior lights will illuminate in the vehicle when the doors are unlocked using the key fob. The interior lights will remain on for 30 seconds after the last door is closed, or until all doors are closed and either the ignition is turned to the ON position or a key fob LOCK button is pressed.
Page 20: To Unlock The Doors And Liftgate
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Your vehicle’s keyfob may have three, four or five buttons (shown), depending on the optional features purchased with your vehicle. This system allows you to lock or unlock the doors and liftgate or activate the panic alarm from distances a minimum of 66 feet (20 meters) using a hand held radio transmitter.
Page 21: To Lock The Doors And Liftgate
5. If the desired programming was not achieved or to reactivate this feature, repeat the above steps. To lock the doors and liftgate: Press and release the LOCK button on the key fob to lock all doors and liftgate. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Test the flash lamps with LOCK feature while outside of the vehicle, by pressing the LOCK button on the key fob with the ignition in the OFF position, and the key removed.
Page 23: Programming Additional Transmitters
Changes or modifications not expressly ap- NOTE: proved by the party responsible for compliance could void the user’s authority to operate the equipment. If your Remote Lock Control fails to operate from a normal distance, check for these two conditions. 1.
Page 24: Battery Replacement
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 7. When a single chime is heard release both buttons. The chime is an indication that you have successfully entered program mode. All fobs that are to be programmed must be done so within 60 seconds of when the chime was heard.
Page 25: Remote Starting System - If Equipped
Transmitter Battery Replacement 2. Remove and replace the batteries. Avoid touching the new batteries with your fingers. Skin oils may cause battery deterioration. If you touch a battery, clean it with rubbing alcohol. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 3.
Page 26 26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To remote start your vehicle, press the REMOTE START button on the key fob twice within three seconds. To indicate that the vehicle is about to start, the parking lights will flash and the horn will sound briefly. Remote Start Transmitter Once the vehicle has started, the engine will run for 15 minutes.
Page 27: Door Locks
The vehicle can be started remotely up to a maximum of two times. The vehicle is also allowed a maximum of one failed start, where the remote start sequence was initiated but cancelled before the engine begins to crank. After either of these conditions, or if the Vehicle Theft Alarm is alarming, or if the PANIC button was pressed, the vehicle must be reset by inserting a valid key into the ignition...
Page 28: Power Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks A power door lock switch is on each front door trim panel. Use this switch to lock or unlock the doors. Power Door Lock Switch If you press the power door lock switch while the key is in the ignition, and any front door is open, the power locks will not operate.
Page 29 3. Place the key into the ignition. 4. Within 10 seconds, cycle the key from the OFF position to the ON position a minimum of four times; ending in the ON position. (do not start the engine). 5. Within 30 seconds, press the driver’s door lock switch in the LOCK direction.
Page 30: Child Protection Door Lock
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 5. Within 30 seconds, press the driver’s door lock switch in the UNLOCK direction. 6. A single chime will sound to indicate the feature has been changed. 7. Repeat the above steps to alternate the availability of this feature.
Page 31: Windows
WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
Page 32: Auto Down
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE windows will operate only when the ignition switch is turned to the ON position and for ten minutes after the ignition is turned OFF or the driver’s door is opened. This feature can be turned off by your authorized dealer. NOTE: The Power Accessory Delay feature will allow the power windows to operate for ten minutes after the ignition it turned OFF.
Page 33: Window Lockout Switch
NOTE: If the window runs into any obstacle during the auto-closure it will reverse direction and then stop. Re- move the obstacle and use the window switch again to close the window. Any impact due to rough road condi- tions may trigger the auto reverse function unexpectedly during auto closure.
Page 34: Liftgate
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LIFTGATE The liftgate can be unlocked using the remote keyless entry transmitter or by activating the power door lock switches located on the front doors. NOTE: When the engine is running from a Remote Start (if equipped), the vehicle must first be unlocked by pressing the remote transmitter UNLOCK button prior to activating the Power Liftgate otherwise the engine will...
Page 35: Power Liftgate - If Equipped
The liftgate will not manually open if the vehicle is in gear or the vehicle speed is above 0 mph (0 km/h). NOTE: • If the liftgate is locked and is not equipped with a powered liftgate, pressing the button on the remote keyless entry transmitter will result in the liftgate becoming unlocked for 30 seconds allowing you to manually access the liftgate area.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: • In the event of a power malfunction to the liftgate, an emergency liftgate latch release can be used to open the liftgate. The emergency liftgate latch release can be accessed through a snap-in cover located on the lift- gate trim panel.
Page 37 • The power liftgate must be in the full open position for any of the buttons to operate. If the liftgate is not fully open, press the remote keyless entry transmitter or overhead console button to fully open the liftgate and then press again to close.
Page 38: Occupant Restraints
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Driving with the liftgate open can allow poison- ous exhaust gases into your vehicle. You and your passengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle.
Page 39: Lap/Shoulder Belts
WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 41 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. Pulling Out Belt and Latchplate 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 plate and pull out the belt.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. •...
Page 43 WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as pos- sible and keep it snug.
Page 44: Adjustable Upper Shoulder Belt Anchorage
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Push in on the anchorage release button to release the anchorage, and then move it up or down to the position that serves you best.
Page 45: Second Row Center Seat Belt
WARNING! A 20% seatback that is not fully latched in the upright position will not protect you properly. Second Row Center Seat Belt The center seating position in the second row has a seat belt assembly that can be converted from the normal emergency locking mode to the automatic locking mode.
Page 46: Rear 60/40 Seat Third Row Center Three Point Belt - If Equipped
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear 60/40 Seat Third Row Center Three Point Belt — If Equipped The center three point seat belt for the third row rear seat may be disconnected to allow the 60% seat back to easily fold down.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Third Row Center Seat Belt Third Row Center Seat Belt To reattach the seat belt to the third row center seat, pull the small (keyed buckle) latch plate forward from the headliner slots and insert it into the keyed buckle until there is an audible click.
Page 48: Seat Belt Pretensioners
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Headliner Stowage Slots Seat Belt Pretensioners The seat belts for both front seating positions are equipped with pretensioning devices that are designed to remove any slack from the seat belt system in the event of a collision.
Page 49 Enhanced Warning System (BeltAlert) will continue to chime and flash the Seat Belt Warning Light for 96 seconds or until the driver’s seat belt is buckled. The Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h).
Page 50: Seat Belts And Pregnant Women
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Programming mode will be cancelled after the feature has toggled with the seat belt still buckled or if the ignition switch is turned to the lock position or 10 seconds after the feature has toggled. The Enhanced Warning System (BeltAlert) can be reacti- vated by repeating this procedure.
Page 51: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbags
Driver And Right Front Passenger Supplemental Restraint System (SRS)—Airbags This vehicle has airbags for both the driver and right front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel. The passenger front airbag is mounted in THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 the instrument panel, above the glove compartment.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the front airbag covers or attempt to manually open them. You may damage the airbags and you could be injured be- cause the airbags are no longer functional. These protective covers for the airbag cushions are de- signed to open only when the airbags are inflating.
Page 53 Here are some simple steps you can follow to minimize the risk of harm from a deploying airbag. 1. Children 12 years and under should always ride buckled up in a rear seat in an appropriate child restraint. Infants in rear-facing child restraints should NEVER ride in the front seat of a vehicle with a passenger front airbag.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision. The airbags work with your seat belt to restrain you properly. In some collisions the airbags won’t deploy at all. Always wear your seat belts even though you have airbags.
Page 55 How the Airbag System Works • The Occupant Restraint Controller (ORC) determines if a frontal collision is severe enough to require the airbags to inflate. The front airbag inflators are de- signed to provide different rates of airbag inflation from direction provided by the ORC. The ORC will not detect roll over.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are located in the center of the steering wheel and the right side of the instrument panel. When the ORC detects a collision requiring the airbags, it signals the inflator units.
Page 57 The following requirements must be strictly adhered to: • Do not modify the front seat center console or center position seat in any way. • Do not use prior or future model year seat covers not designated for the specific model being repaired. Al- ways use the correct seat cover specified for the vehicle.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. As the airbags deflate you may see some smoke-like particles. The particles are a normal by- product of the process that generates the nontoxic gas used for airbag inflation.
Page 59 Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured if the airbag system is not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 60: Event Data Recorder (Edr)
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The light flickers or comes on and remains on while driving. NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection.
Page 61 may be released for incorporation in aggregate crash databases, such as those maintained by the US govern- ment and various states. Data of a potentially sensitive nature, such as would identify a particular driver, ve- hicle, or crash, will be treated confidentially. Confidential data will not be disclosed by DaimlerChrysler Corpora- tion to any third party except when: 1.
Page 62: Child Restraint
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint Everyone in your vehicle needs to be buckled up all the time - babies and children, too. Every state in the United States and all Canadian provinces require that small children ride in proper restraint systems.
Page 63 LATCH child restraint anchorage system. (See the LATCH - Child Seat Anchorage System section.) • Rearward-facing child seats must NEVER be used in the front seat of a vehicle with a front passenger airbag. An airbag deployment could cause severe injury or death to infants in this position.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the face or neck, move the child closer to the center of the vehicle. Never allow a child to put the shoulder belt under an arm. WARNING! •...
Page 65 around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt. The cinching latch plate will keep the belt tight, however, any seat belt system will loosen with time, so check the belt occasionally and pull it tight if necessary.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE and hooks for connection to the top tether anchorages have been available for some time. For some older child restraints, many child restraint manufacturers offer add-on tether strap kits or retro-fit kits. You are urged to take advantage of all the available attachments provided with your child restraint in any vehicle.
Page 67 Second Row Seat Right Side Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 were provided with the child restraint system.
Page 68 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE anchorages. Next attach the lower hooks or connectors over the top of the anchorage bars, pushing aside the seat cover material. Then attach the tether strap to the anchor- age located on the back of the seat, being careful to route the tether strap to provide the most direct path between the anchor and the child restraint.
Page 69 Installing Child Restraints Using the Vehicle Seat Belt The second and third row seats have either cinching latch plates or automatic locking retractors which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchor positions directly behind the child seat to secure a child restraint top tether strap.
Page 71: Engine Break-In Recommendations
WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 72: Safety Tips
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. SAFETY TIPS Exhaust System WARNING! Exhaust gases contain carbon monoxide, an ex-...
Page 73: Safety Checks You Should Make Inside The Vehicle
Safety Checks You Should Make Inside The Vehicle Heater Defroster Ducts Inspect the heater defroster ducts for proper operation. Check for proper air flow through all defroster ducts. If there are any question regarding the operation of your heater defroster ducts, have the system checked by an authorized dealer Seat Belts Inspect the belt system periodically, checking for cuts,...
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lights Check the operation of all exterior lights. Check turn signal and high beam indicator lights on the instrument panel. Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks.
Page 75: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......79 Inside Day/Night Mirror ....79 Automatic Dimming Mirror —...
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... . 108 Front Seat Manual Seat Adjustment .
Page 77 Headlight Delay ..... . 133 Automatic Headlights — If Equipped ..133 Headlights, Parking Lights, Panel Lights ..134 Illuminated Entry .
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome/Reading Lights ....151 Electronic Vehicle Information Center (EVIC) — If Equipped ......152 Compass/Temperature Button .
Page 79: Mirrors
MIRRORS Inside Day/Night Mirror The mirror should be adjusted to center on the view through the rear window. A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Day/Night Mirror UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of truck).
Page 80: Automatic Dimming Mirror - If Equipped
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped This mirror will automatically adjust for annoying head- light glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror.
Page 81: Outside Mirrors
CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror.
Page 82: Illuminated Vanity Mirrors - If Equipped
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mirror Directions To adjust a mirror, turn the control wand toward the left or right mirror positions indicated. Tilt the control wand in the direction you want the mirror to move. When finished adjusting the mirror, turn the control to the center position to prevent accidentally moving a mirror.
Page 83: Heated Mirrors - If Equipped
Lighted Vanity Mirror Heated Mirrors — If Equipped Heated mirrors are automatically activated when you depress the rear window defroster switch located on the instrument panel. The light will illuminate to indicate that the heating elements are ON. Turning Off the rear window defroster or the ignition will deactivate the heated mirrors.
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro-...
Page 85: Operations
UConnect™ Switches The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. See www.chrysler.com/uconnect for supported phones. If your cellular phone supports a different profile (e.g., UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Headset Profile), you may not be able to use any UCon- nect™...
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for the voice on beep, which follows the Ready prompt or another prompt. • For certain operations, compound commands can be used. For example, instead of saying Setup and then Phone Pairing, the following compound command can be said: Setup Phone Pairing.
Page 87 Bluetooth™ enabled cellular phone. NOTE: The UConnect™ system use requires a cellular phone equipped with the Bluetooth Hands-Free Profile, version 0.96 or higher. See www.chrysler.com/uconnect for supported phones. To complete the pairing process, you will need to refer- ence your cellular phone owner’s manual.
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your cellular phone a priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to your UConnect™ system. However, at any given time, only one cellular phone can be in use, connected to your UConnect™...
Page 89 Call/Dial by Saying a Name • Press the “Phone” button to begin. • After the Ready prompt and the following beep, say “Dial” or Call. • System will prompt you to say the name of the person you want call. •...
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished adding an entry into the phone- book, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The UConnect™...
Page 91 Delete Entries in the UConnect™ Phonebook NOTE: Editing phonebook entries is recommended when vehicle is not in motion. • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook Delete. • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete.
Page 92: Phone Call Features
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook List Names. • The UConnect™ system will play the names of all the phonebook entries.
Page 93 Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your cell phone.
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Conference Call When two calls are in progress (one active and one on hold), press and hold the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 95: Uconnect™ System Features
• After ignition key is switched to off, a call can continue on the UConnect™ system for certain duration, after which the call is automatically transferred from the UConnect™ system to the mobile phone. • An active call is automatically transferred to the mobile phone after ignition key is switched to off.
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Emergency and the UConnect™ system will instruct the paired cellular phone to call the emergency num- ber. This feature is only supported in the USA. NOTE: The emergency number dialed is based on the Country where the vehicle is purchased (911 for USA and Canada and 060 for Mexico).
Page 97 Paging To learn how to page, refer to Working with Automated Systems. Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™ system. Voice Mail Calling To learn how to access your voice mail, refer to Working with Automated Systems.
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g., the UConnect™ system will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. •...
Page 99: Advanced Phone Connectivity
Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. In order to mute the UConnect™ system: •...
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, then follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names •...
Page 101: Things You Should Know About Your Uconnect™ System
Delete UConnect™ Paired Cellular Phones • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing. • At the next prompt, say Delete and follow the prompts. • You can also press the Voice Recognition’ button anytime while the list is being played and then choose the phone you wish to delete.
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Recognition (VR) • Always wait for the beep before speaking. • Speak normally, without pausing, just as you would speak to a person sitting approximately eight (8) feet away from you. • Make sure that no one other than you is speaking during a voice recognition period.
Page 103 • Even though international dialing for most number combinations is supported, some shortcut dialing number combinations may not be supported. Far End Audio Performance • Audio quality is maximized under: • low-to-medium blower setting, • low-to-medium vehicle speed, • low road noise, •...
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105...
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 107 Voice Commands Primary Alternate(s) zero three four five seven eight nine star (*) plus (+) pound (#) add location UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 call cancel confirmation prompts continue delete dial edit emergency English erase all Espanol Fancais help home language...
Page 108: Seats
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mobile mute mute off new entry pager pair a phone phone pairing pairing phonebook phone book previous record again redial return to main menu return or main menu select phone select send set up phone settings or phone set up towing assistance...
Page 109: Front Seats Manual Seat Recliners
Manual Seat Adjuster UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 110: Manual Lumbar Support Adjustment - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only when the vehicle is parked.
Page 111: Way Driver's Power Seat - If Equipped
To lower the head restraint, depress the release button located at the base of the head restraint and push down on the head restraint. Head Restraint Adjustment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 8 - Way Driver’s Power Seat — If Equipped The driver power seat switches are located on the left side of the driver seat lower side trim.
Page 112: Way Passenger's Power Seat - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the right side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjustment. The top switch controls the seatback recline adjustment.
Page 113 With the ignition switch in the RUN position, depressing the heated seat switch rocker to its momentary high or low position provides power to the heated seat element and maintains the requested temperature setting. If the heated seat switch is depressed to a different position (low or high) than the currently selected state, the re- quested temperature setting will change to a new selec- tion.
Page 114 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE off. Both of the indicators on identifies High heat level. The lower indicator on only, identifies Low heat level. NOTE: The high heat setting will operate for approxi- mately 30 minutes. After 30 minutes, the system will automatically transition to the low heat setting.
Page 115: Second Row Bucket Seats - Fold And Tumble
Second Row Bucket Seats — Fold and Tumble Second row bucket seats have seatback recliners on both seating positions. Raising the lever allows the seatback to be reclined an additional 11 degrees. The second row bucket seats can be folded and tumbled forward for easy access to the third seat or rear cargo area.
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Pull up on the release handle and lift to tumble the seat fully forward. If the seat contacts the rear of the front seat, move the front seat forward. Tumbling the Seat Forward To relatch the seat, tilt the seat rearward and push down firmly to engage the rear attachments.
Page 117: Second Row 40/20/40 Seat - Fold And Tumble
Tumble Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! In a collision, you or others in your vehicle could be injured if seats are not properly latched to their floor attachments. Always be sure the seats are fully latched. Second Row 40/20/40 Seat —...
Page 118 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Second row leather seats have seatback recliners at the 40% seating positions. Raising the lever allows the seat- back to be reclined an additional 11 degrees. Fold, Tumble, and Recline Lever To Fold the 40% seatbacks fully raise the lever on the side of the seat to release the seatback.
Page 119 Fold, Tumble, and Recline Lever UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 To Tumble the 40% seat, fully raise the lever on the side of the seat to release the floor latches and tumble the seat. WARNING! Do not drive the vehicle with the outer 40% second row seats in the tumbled position.
Page 120: Third Row Seat Bench - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The seatback must be fully folded into the down position to allow the lever to be raised enough to release the floor latches. Tumble Lever To Fold and Tumble the 2nd row 40% seats from the 3rd row, fully raise the lever at the rear of the seat to fold the seatback.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Seat Cushion Pockets Seat Cushion Movement Up And Forward...
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Folded CAUTION! When loading cargo into the rear of you vehicle with the 3rd row seat folded flat, be careful not to damage the material on the head restraints. NOTE: The seat belt buckles are hinged to fold with the seat back.
Page 123: Third Row 60/40 Folding - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Third Row 60/40 Folding — If Equipped Third Row Seat 40% Seatback Fold Third Row Seat...
Page 124 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Third Row Seat Features Third Row Seat Folded Forward...
Page 125: Driver Memory System - If Equipped
Third Row Seat Return Pull Strap DRIVER MEMORY SYSTEM — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat position, driver’s outside mirror position, adjustable brake and accelerator pedals position, Automatic Tem- perature Control (ATC) temperature and radio station UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 preset settings.
Page 126: Setting Memory Positions And Linking Remote
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions and Linking Remote Keyless Entry Transmitter to Memory NOTE: Each time the SET (S) button and a numbered button (1 or 2) are pressed, you erase the memory settings for that button and store new settings. 1.
Page 127: Memory Position Recall
Memory Position Recall NOTE: • The driver’s seat belt must be unbuckled to recall memory positions. • The vehicle must be in Park to recall memory posi- tions. • Not all motors may be moved at one time. Please refer to the 8-way power seat description.
Page 128: Self-Limiting Control
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Within 10 seconds, press and release the UNLOCK button on the Remote Keyless Entry transmitter. To disable another transmitter linked to either memory position, repeat steps 1-3 for each transmitter. NOTE: The capability to link Remote Keyless Entry transmitters to memory is enabled when delivered from the factory.
Page 129: To Open And Close The Hood
the seat is positioned rearward enough and no benefit from moving the seat any farther rearward. NOTE: The Easy Entry/Easy Exit feature can be en- abled or disabled through the programmable features in the Electronic Vehicle Information Center (EVIC). For details, refer to “EASY EXIT SEAT,”...
Page 130 130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Then push the safety latch lever to the left. It is located between the grille and hood opening right of the center. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the center front edge of the hood to ensure that both latches engage.
Page 131: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 LIGHTS Headlight Switch Headlight Switch Location...
Page 132: Interior Lights
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Interior Lights Dimmer Control Courtesy and dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or when the UNLOCK button is pressed on the key fob.
Page 133: Headlight Delay
If the ignition is off and any door is left ajar for eight minutes or the dimmer control is rotated upwards for 15 minutes, the interior lights will automatically turn off. If the headlights remain on while the ignition is cycled off, the exterior lights will automatically turn off after 8 minutes.
Page 134: Headlights, Parking Lights, Panel Lights
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights, Parking Lights, Panel Lights When the headlight switch is rotated to the first position to the right, the parking lights, taillights, side marker lights, license plate light and instrument panel lights are all turned on.
Page 135: Lights-On Reminder
Lights-on Reminder If the headlights, parking lights, or courtesy lights are left On, after the ignition is turned Off, a continuous fast chime will sound when the driver’s door is opened. Fog Lights — If Equipped Fog Light Switch UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 The fog lights are turned ON by placing the headlight rotary control in the parking light, headlight, or Auto position and pressing the fog light button.
Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE of the front and rear turn signal lights. If an indicator fails to light when the lever is moved, it would suggest that the switch or indicator lamp is defective. If a defective bulb or wiring circuit is detected for the turn signal system, the arrow indicators will flash at a faster rate.
Page 137 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will momentarily allow the high and low beams to energize at the same time. Within one second the headlights will switch to high beams.
Page 138: Windshield Wipers And Washers
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Windshield Wipers Windshield Wiper Switch The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle,...
Page 139: Windshield Washers
NOTE: Avoid using the wiper blades to remove frost or Ice from the windshield. NOTE: If the front wiper is operating when the ignition is turned off, the wiper will automatically return to the Park position. When the vehicle is restarted, the wipers will resume operation.
Page 140: Tilt Steering Column
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, pull rearward on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever forward to lock the column firmly in place.
Page 141: Driver Adjustable Pedals - If Equipped
DRIVER ADJUSTABLE PEDALS — IF EQUIPPED Adjustable Pedals Switch The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
Page 142: Electronic Speed Control - If Equipped
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
Page 143: To Activate
To Activate NOTE: Activating any two speed control switch func- tions simultaneously (i.e. SET and CANCEL) will cause the speed control system to shut off and will erase the memory. Push the ON/OFF button to the ON position. In the instrument cluster, the word “CRUISE”...
Page 144: To Resume Speed
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed To resume a previously set speed, push and release the RESUME button. Resume can be used at any speed above (refer to the table below for the speed for your specific engine).
Page 145: To Accelerate For Passing
Functions Engage Speed Minimun RESUME Speed ACCEL Increase DECEL Decrease Dropout Speed To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
Page 146: Rear Park Assist System - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Speed Control can be dangerous where the system can’t maintain a constant speed. Your vehicle could go too fast for the conditions, and you could lose control. An accident could be the result. Don’t use Speed Control in heavy traffic or on roads that are winding, icy, snow-covered, or slippery.
Page 147 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 The warning display contains two sets of yellow and red LEDs, one set to warn of obstacles behind the left rear of the vehicle and the other set to warn of obstacles behind the right rear of the vehicle.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM: REAR CORNERS 1st LED 2nd LED 3rd LED 4th LED 31.5 in. (80 cm) 5th LED 25.5 in. (65 cm) 6th LED 20 in. (50 cm) 7th LED 16 in.
Page 149 WARNING! • Drivers must be careful when backing up even when using the Rear Park Assist System. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings.
Page 150: Overhead Console
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Ensure that the rear bumper is free of dirt and debris to keep the system operating properly. • Jackhammers, large trucks, and other vibrations could affect the performance of the system. If “Service Park Assist System”...
Page 151: Courtesy/Reading Lights
Courtesy/Reading Lights Near the front of the console are two courtesy/reading lights. Both lights illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (fully upward position), or when the UNLOCK button is pressed on the Remote Keyless Entry transmitter, if so equipped.
Page 152: Electronic Vehicle Information Center (Evic) - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The dome/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle. Overhead Console Electronic Vehicle Information Center (EVIC) — If Equipped Pressing the menu button will change the display to one of the following features:...
Page 153 Trip Functions Pressing the STEP button allows you to scroll through one of the following Trip Function features: • TRIP – Shows the total distance traveled since the last reset. To reset the TRIP function, press and hold the RESET button. •...
Page 154 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE change to a text display of LOW FUEL. This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn off the LOW FUEL text and a new DTE value will display.
Page 155 • COOLANT LOW • ESP SYSTEM DEACTIVATED • LIFTGATE OPEN Personal Settings (Customer Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in PARK. If the trans- mission is not in PARK the EVIC will display NOT AVAILABLE and VEHICLE NOT IN PARK.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE remote keyless entry unlock button twice to unlock the passenger’s doors. To make your selection, press and release the RESET button until “DRV DR 1st ” appears. • “RKE UNLOCK ALL DR 1ST” – When All ALL DR 1ST is selected, all of the doors will unlock on the first press of the remote keyless entry unlock button.
Page 157 • HEADLAMPS W /WIPERS > YES – When ON is selected, the headlamps will automatically turn on when the wiper switch is activated. • EASY EXIT SEAT > YES – When ON is selected, and the key is removed from the ignition, the driver’s seat will automatically move rearward to allow easy exit.
Page 158: Compass/Temperature Button
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE change your variance according to your variance on the variance map. Refer to Compass Variance, in this section for additional information. • “COMPASS CALIBRATE > YES” – Press the RESET button to manually calibrate the compass. Refer to Manual Compass Calibration, in this section for addi- tional information.
Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 3. Press the STEP button until “Calibrate Compass YES” is displayed. 4. Press and release the RESET button to start the cali- bration. The message “CAL” will display on the compass temperature screen in the EVIC. 5.
Page 160: Garage Door Opener - If Equipped
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Turn the ignition switch to the ON/RUN position. 2. Press the menu button until Personal Set- tings is displayed. 3. Press the STEP button until “Compass Variance” is displayed. 4. Press and release RESET button until the proper variance zone is selected according to the map.
Page 161 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured. Only use this transceiver with a garage door opener that has a “stop and reverse”...
Page 162: Programming Homelink
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink The Electronic Vehicle Information Center (EVIC) fea- tures a driver–interactive display which includes HomeLink system messages. The EVIC display is located in the overhead console. NOTE: When programming a garage door opener, it is advised to park outside the garage.
Page 163 3. Simultaneously press and hold both the HomeLink button that you want to train and the hand-held trans- mitter button. Do not release the buttons until step 4 has been completed. The EVIC will display “CHANNEL X TRAINING”, once the transmitter is programmed the EVIC will display “CHANNEL X TRAINED”.
Page 164: Canadian Programming/Gate Programming
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 6. Firmly press and release the learn or smart button. (The name and color of the button may vary by manu- facturer.) NOTE: There are 30 seconds in which to initiate step eight. 7.
Page 165: Using Homelink
NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the cycling process to prevent possible overheating. Using HomeLink To operate, simply press and release the programmed HomeLink button. Activation will now occur for the trained device (i.e.
Page 166: Security
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security Garage Door Opener Operation with Security Alarm (if equipped) If your vehicle is equipped with the Security Alarm feature, the operation of the HomeLink feature will be purposely inhibited if the Security Alarm is Armed . This prevents HomeLink operation due to un-authorized vehicle entry.
Page 167: Power Sunroof - If Equipped
POWER SUNROOF — IF EQUIPPED The power sunroof control is located between the sun visors on the overhead console. Pressing the open end of the rocker switch once moves the panel to a comfort stop position short of full opening. Pressing the switch a second time causes the panel to continue moving rearward, up to the full-open position.
Page 168: Wind Buffeting
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Never leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Don’t leave the keys in the ignition.
Page 169: Sunroof Maintenance
the rear windows open, open the front and rear windows together to minimize the buffeting. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting or open any window. Sunroof Maintenance Use only a nonabrasive cleaner and a soft cloth to clean the glass panel.
Page 170: 115V Inverter Outlet - If Equipped
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115V Inverter Outlet – If Equipped This vehicle may also be equipped with a 115 Volt (150 Watts Maximum) outlet on the rear of the front center console. These outlets can power cell phones, electronics and other low power devices.
Page 171: Electrical Outlet Use With Engine Off (Battery Fed Configuration)
115V Inverter Plug UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Electrical Outlet Use With Engine OFF (Battery Fed Configuration) CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.).
Page 172: Floor Console
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reconfiguring Power Outlets To reconfigure the outlets, be sure the ignition is OFF before removing the fuse. The reconfigurable fuse loca- tion is a special design that allows the fuse to be installed in two different ways.
Page 173 • Portable phone storage bin • Portable phone cord routing between lid and base on forward edge • 12 Volt reconfigurable power outlet inside storage compartment • Side open armrest lid • Tissue holder & pen holder • Coin slots •...
Page 174 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Center Console The front storage bin in the center console is equipped with a removable bin mat. This mat can be removed by pulling on the tab located on the front edge of the bin mat.
Page 175: Rear Floor Console Features - If Equipped
being stored in the bin. To use, plug in the portable power recharge cord and place the cord along the opening under the forward portion of the storage bin. Close the console armrest lid and plug the power cord into the phone while resting the phone in the bin.
Page 176: Factory Installed Roof Luggage Rack
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FACTORY INSTALLED ROOF LUGGAGE RACK The load carried on the roof when equipped with a luggage rack must not exceed 68 kg (150 lbs.), and should be uniformly distributed over the cargo area. The side rails between the stantions should be used to tie down cargo.
Page 177 CAUTION! To avoid damage to the roof rack and vehicle, do not exceed the maximum roof rack load capacity. Always distribute heavy loads as evenly as possible and secure the load appropriately. Long loads which extend over the windshield, such as wood panels or surfboards, should be secured to both the front and rear of the vehicle.
Page 178: Cargo Management System-If Equipped
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO MANAGEMENT SYSTEM—IF EQUIPPED The cargo management system consists of a removable cargo liner and removable cargo organizer. 1 — Side Cover Latch 2 — Main Cover Latch 3 — Cargo Divider Handles To open the side cover, pull on the cover latch, and attach the cord to the upper cargo net hook.
Page 179 To open the Cargo divider, lift up on the cargo divider handles, raising the doors to the full open position. Raise the side panels until they engage into the doors. 1 — Cargo Divider Door 2 — Cargo Divider Side Panel UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 To remove the cargo management system from the ve- hicle, pull the right hand side of the organizer towards...
Page 181: Instrument Panel And Controls
INSTRUMENT PANEL AND CONTROLS CONTENTS Instruments And Controls ....185 Instrument Cluster ..... . 186 Instrument Cluster Description .
Page 182 182 INSTRUMENT PANEL AND CONTROLS Operating Instructions - Hands Free Phone — If Equipped ......207 Operating Instructions - Satellite Radio —...
Page 183 Selecting a Channel ....228 Storing And Selecting Pre-Set Channels ..229 Using The PTY (Program Type) Button (If Equipped) .
Page 184 184 INSTRUMENT PANEL AND CONTROLS Rear Rotary Temperature Control ..245 Front Unit To Rear Unit Chart ... . 246 Operating Tips ..... . . 246 Operating Tips Chart .
Page 185: Instruments And Controls
INSTRUMENT PANEL AND CONTROLS 185 INSTRUMENTS AND CONTROLS...
Page 186: Instrument Cluster
186 INSTRUMENT PANEL AND CONTROLS Instrument Cluster...
Page 187: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Fuel Gage The fuel gauge shows level of fuel in tank when ignition switch is in the ON position. 2. Temperature Gage The temperature gage indicates engine coolant temperature. Any reading within the normal range indicates that the cooling system is operat- ing satisfactorily.
Page 188 188 INSTRUMENT PANEL AND CONTROLS left/right turn signal is left on with the engine RPM vehicle speed greater than 15 mph (24 km/h) for more than one mile. 4. Low Fuel Warning Light This indicator lights when the fuel gauge reads 1/8 of a tank or less.
Page 189 CAUTION! Driving with a hot engine cooling system could damage your vehicle. If the temperature light is on, safely pull over and stop the vehicle. Idle the vehicle in neutral with the air conditioner turned off until the light turns off. If the if the light remains on, turn the engine off immediately, and call for service.
Page 190 190 INSTRUMENT PANEL AND CONTROLS 11. Security Light This light will flash rapidly for approximately 15 seconds when the vehicle theft alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The security light will also come on for about three seconds when the ignition is first turned on.
Page 191 15. Gear Selector The electronic gear selector display is self-contained within the instrument cluster. It displays the position of the automatic transmission shift lever, and the relation of each position to all other positions. For a good signal the display will place a box around the selected transmission range (PRND21).
Page 192 192 INSTRUMENT PANEL AND CONTROLS replacement, be sure to keep a record of the reading before and after the service so that the correct mileage can be determined. 18. Electronic Stability Program (ESP) Indicator Light The yellow ESP indicator light in the speedom- eter area illuminates with the key in the igni- tion switch turned to the ON/RUN position.
Page 193 on for 15 seconds as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. 21. BRAKE System Warning Light The red “BRAKE” warning light will come on when the ignition key is first turned on, and stay on briefly as a bulb check.
Page 194 194 INSTRUMENT PANEL AND CONTROLS NOTE: • The ESP/TCS Indicator Light and the ESP/ BAS Warning Lamp come on momentarily each time the ignition switch is turned ON. • The ESP Control System will make buzzing or clicking sounds when it is actively operating.
Page 195 24. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those...
Page 196 196 INSTRUMENT PANEL AND CONTROLS CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system op- eration or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Page 197: Electronic Digital Clock
29. TOW/HAUL The TOW/HAUL button is located at the end of the gear shift lever. This light will illuminate when the TOW/ HAUL button has been selected. 30. 4LOW Indicator Indicates transfer case is in 4LOW position. 31. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display.
Page 198: Setting The Analog Clock
198 INSTRUMENT PANEL AND CONTROLS 5. To exit, press any button/knob or wait approximately 5 seconds. SETTING THE ANALOG CLOCK To set the analog clock at the top center of the instrument panel, press and hold the button until the setting is correct.
Page 199: Electrical Disturbances
Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.
Page 200: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
200 INSTRUMENT PANEL AND CONTROLS SALES CODE REF — AM/FM/CD (SINGLE DISC) RADIO WITH OPTIONAL SATELLITE RADIO AND HANDS FREE PHONE CAPABILITY NOTE: The radio sales code is located on the lower right side of your radio faceplate. REF Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio.
Page 201 Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 202 202 INSTRUMENT PANEL AND CONTROLS Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune/ Audio control. 3. After the hours are adjusted, press the right side Tune/Audio control to set the minutes.
Page 203 Press the rotary TUNE control a fourth time and BAL will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers. Press the rotary TUNE control a fifth time and FADE will display.
Page 204: Operation Instructions - Cd Mode
204 INSTRUMENT PANEL AND CONTROLS Operation Instructions - CD Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Inserting The Compact Disc (Single CD Player) Gently insert one CD into the CD player with the CD label facing up.
Page 205 SCAN Button (CD Mode) Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. EJECT Button (CD Mode) Press this button and the disc will unload and move to the entrance for easy removal.
Page 206: Operation Instructions - Auxiliary Mode
206 INSTRUMENT PANEL AND CONTROLS Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, cassette player, or microphone and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers.
Page 207: Operating Instructions - Hands Free Phone - If Equipped
TIME Button (Auxiliary Mode) Press this button to change the display from elapsed playing time to time of day. The time of day will display for 5 seconds. RW/FF (Auxiliary Mode) No function. RND/SET Button (Auxiliary Mode) No function. Mode Button (Auxiliary Mode) Press the mode button repeatedly to select between the CD player and Satellite Radio (if equipped).
Page 208: Sales Code Raq - Am/Fm/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (Ves) Capabilities
208 INSTRUMENT PANEL AND CONTROLS SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO WITH OPTIONAL SATELLITE RADIO, HANDS FREE PHONE, AND VEHICLE ENTERTAINMENT SYSTEMS (VES) CAPABILITIES NOTE: The radio sales code is located on the lower right side of your radio faceplate. RAQ Radio Operating Instructions - Radio Mode NOTE: The ignition switch must be in the ON or ACC...
Page 209 Mode Button (Radio Mode) Press the mode button repeatedly to select between the CD player, Satellite Radio, or Vehicle Entertainment System (VES) (if equipped). SEEK Button (Radio Mode) Press and release the SEEK button to search for the next listenable station in either AM/FM or Satellite (if equipped) mode.
Page 210 210 INSTRUMENT PANEL AND CONTROLS Time Button Press the time button and the time of day will be displayed for 5 seconds. Clock Setting Procedure 1. Press and hold the time button until the hours blink. 2. Adjust the hours by turning the right side Tune / Audio control.
Page 211 Press the rotary TUNE control a third time and TREBLE will display. Turn the TUNE control to the right or left to increase or decrease the Treble tones. Press the rotary TUNE control a fourth time and BAL- ANCE will display. Turn the TUNE control to the right or left to adjust the sound level from the right or left side speakers.
Page 212 212 INSTRUMENT PANEL AND CONTROLS Jazz News Nostalgia Oldies Personality Public Rhythm and Blues Rhythm_and_Blues Religious Music Religious Talk Rock Soft Soft Rock Soft Rhythm and Blues Sports Talk Top 40 Weather By pressing the SEEK button when the PTY icon is Jazz displayed, the radio will be tuned to the next frequency News...
Page 213: Operation Instructions - (Cd Mode For Cd Audio Play)
You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET/DIR button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 214 214 INSTRUMENT PANEL AND CONTROLS CAUTION! This CD player will accept 4 3/4 inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc.
Page 215: Load/Eject Button (Cd Mode For Cd Audio Play)
LOAD/EJECT Button (CD Mode for CD Audio Play) LOAD/ EJECT - Load Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD is being loaded. The radio will display PLEASE WAIT and prompt when to INSERT DISC.
Page 216 216 INSTRUMENT PANEL AND CONTROLS TIME Button (CD MODE for CD Audio Play) Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF (CD MODE for CD Audio Play) Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed.
Page 217: Notes On Playing Mp3 Files
Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CD-ROM, CD-R and CD-RW.
Page 218 218 INSTRUMENT PANEL AND CONTROLS Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- sion as MP3 files. Non-MP3 files named with the *.mp3 extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file.
Page 219: Operation Instructions
Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: •...
Page 220 220 INSTRUMENT PANEL AND CONTROLS LOAD / EJECT - Eject Press the LOAD/ EJECT button and the push- button with the corresponding number where the CD was loaded and the disc will unload and move to the entrance for easy removal. Radio display will show EJECTING DISC when the disc is being ejected and prompt the user to remove the disc.
Page 221 AM/FM Button (CD Mode for MP3 Play) Switches back to Radio mode. RND/ PTY Button (CD Mode for MP3 Play) Pressing this button plays files randomly. SET/DIR Button (CD Mode for MP3 Play) Press the SET/DIR Button to display folders, when playing an MP3 discs that have a file/folder structure.
Page 222: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio With Navigation System
222 INSTRUMENT PANEL AND CONTROLS SALES CODE REC — AM/FM/CD (6–DISC) RADIO WITH NAVIGATION SYSTEM REC Radio Satellite Navigation Radio with CD Player with MP3 Capability (REC) - combines a Global-Positioning System-based navigation system with an integrated color screen to provide maps, turn identification, selection menus and instructions for selecting a variety of destina- tions and routes, AM/FM stereo radio and six-disc CD changer with MP3 capability.
Page 223 the worldwide standard for time. This makes the sys- tem’s clock very accurate once the appropriate time zone and daylight savings information is set. 1. At the Main Menu screen, highlight “Clock Setup” and press ENTER OR press and hold for 3 seconds the TIME button on the unit’s faceplate.
Page 224 224 INSTRUMENT PANEL AND CONTROLS User Defined Clock If you wish to set the clock to a time different than the system clock, you can manually adjust the time by choosing the “User Defined Clock” option. 1. At the Clock Setup screen highlight “Displayed Clock: User Defined Clock”.
Page 225: Audio Clock Display
Audio Clock Display Select this option to change the size of the clock on the audio screens. 1. When you are at an audio screen, quickly press the TIME button on the navigation faceplate. 2. In this example the large clock appears on the screen. INSTRUMENT PANEL AND CONTROLS 225 3.
Page 226: Video Entertainment System (Sales Code Xrv) - If Equipped
226 INSTRUMENT PANEL AND CONTROLS VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The system is located in the headliner behind the front row seat.
Page 227: Electronic Serial Number/Sirius Identification Number (Esn/Sid)
Electronic Serial Number/Sirius Identification Number (ESN/SID) The Electronic Serial Number/Sirius Identification Num- ber is needed to activate your Sirius Satellite Radio system. To access the ESN/SID, refer to the following steps: ESN/SID Access With REF Radios With the ignition switch in the ACCESSORY position and the radio OFF, press the CD Eject and Time buttons simultaneously for 3 seconds.
Page 228: Selecting Satellite Mode In Ref, Raq, And Rak
228 INSTRUMENT PANEL AND CONTROLS Selecting Satellite Mode in REF, RAQ, and RAK Radios Selecting Satellite Mode — REF Radio Press the MODE button repeatedly until the word SAT appears in the display. A CD may remain in the radio while in the Satellite radio mode.
Page 229: Storing And Selecting Pre-Set Channels
Storing and Selecting Pre-Set Channels In addition to the 12 AM and 12 FM pre-set stations, you may also commit 12 satellite stations to push button memory. These satellite channel pre-set stations will not erase any AM or FM pre-set memory stations. Follow the memory pre-set procedures that apply to your radio.
Page 230: Reception Quality
230 INSTRUMENT PANEL AND CONTROLS Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception in the form of short audio mutes.
Page 231: Radio Operation
The right hand control is a rocker type switch with a push button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The button located in the center of the right hand control will switch modes to Radio or CD.
Page 232: Compact Disc Maintenance
232 INSTRUMENT PANEL AND CONTROLS COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 233: Climate Controls
CLIMATE CONTROLS Manual Control The Air Conditioning and Heating System is designed to make you comfortable in all types of weather. The following describes its operation: INSTRUMENT PANEL AND CONTROLS 233 Air Conditioning Operation To turn the air conditioning On or Off perform the following steps: •...
Page 234: Front Blower Control
234 INSTRUMENT PANEL AND CONTROLS engine speed or power may be noticed when the com- pressor cycles. This is a normal occurrence since the compressor will cycle on and off to maintain comfort and improve fuel economy. Front Blower Control The Front Blower controls the amount of air delivered to the passenger...
Page 235 Recirculation Mode (Panel or Bi-Level) Select either the Panel or Bi-Level mode positions when the outside air contains smoke, odors, high humidity, or if rapid cooling of the interior is desired. This feature allows for recir- culation of interior air only, when ei- ther of these positions are selected.
Page 236 236 INSTRUMENT PANEL AND CONTROLS Defrost Outside air is primarily directed to the windshield through the defroster outlet located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 237: Rear Temperature Control - If Equipped
Rear Temperature Control — If Equipped Rotating this knob left to the “REAR CONTROL” position allows the passengers in the second and third row seats to control the blower speed and temperature by means of the rear control located in the rear of the center floor console as described under “Rear Zone Control.”...
Page 238: Automatic Temperature Control (Atc) - If Equipped
238 INSTRUMENT PANEL AND CONTROLS Automatic Temperature Control (ATC) — If Equipped The control can be turned on by pressing the POWER knob. When the control is turned on, it will be in the last mode prior to being turned off. Pressing the POWER knob again will turn off the control.
Page 239: Level Of Automatic Control
located in the overhead console to measure the tem- perature of the driver and passengers. Based on the sensor input, the system will automatically ocntrol comfort by varying the temperature, fan speed, and mode. This maintains a comfortable temperature, even under changing conditions.
Page 240: Manual Control (Atc)
240 INSTRUMENT PANEL AND CONTROLS Manual Control (ATC) You also may choose to customize your comfort by selecting the fan speed and mode manually. Turning the fan speed knob or any mode button places the system into manual operation. While in manual operation there are six fan speeds available and the choice of any mode.
Page 241 Recirculate Button Press this button to recirculate the air inside the vehicle. Outside air is prevented from entering the vehicle. Use this mode to temporarily block out any outside odors, smoke, dust or when rapid cooling of the interior is required. Manual control of Recirculation is possible only in Panel, Floor, and Bi-Level modes.
Page 242 242 INSTRUMENT PANEL AND CONTROLS Bi-Level Air flows through the outlets located in the instru- ment panel and those located on the floor. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets.
Page 243 CONTROL IN REAR This allows the passengers in the second row seats to control the blower speed and temperature by means of the rear control located in the rear of the center floor console as described under the Rear Zone Climate Control.
Page 244: Rear Zone Climate Control - If Equipped
244 INSTRUMENT PANEL AND CONTROLS Rear Zone Climate Control — If Equipped Headliner air comes from the outlets in the headliner. Each of these outlets can be individually adjusted to direct the flow of air. Moving the air vane knobs on the outlets to one side will shut off the airflow.
Page 245: Rear Rotary Temperature Control
Rear Rotary Blower Control The second row seat occupants have control of the rear blower speed, only when the front control unit is in the “REAR CONTROL” position or CONTROL IN REAR for ATC. The rear blower switch has an “Off” position and a range of blower speeds.
Page 246: Front Unit To Rear Unit Chart
246 INSTRUMENT PANEL AND CONTROLS Front Unit to Rear Unit Chart If the Front Control is Rear Airflow will come selected from Panel Headliner Bi-Level Headliner Floor Floor Floor Defrost Floor Operating Tips Fast Cooldown For a fast cooldown, set the blower fan to the highest setting, set the mode control to the panel fresh position, press the snowflake button to turn on the air condition- ing, and drive with the windows open for the first few...
Page 247 Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Summer Operation Air conditioned vehicles must be protected with a high quality antifreeze coolant during summer to provide proper corrosion protection and to raise the boiling point...
Page 248: Operating Tips Chart
248 INSTRUMENT PANEL AND CONTROLS Operating Tips Chart...
Page 249: Rear Window Features
REAR WINDOW FEATURES Rear Window Wiper/Washer INSTRUMENT PANEL AND CONTROLS 249 A rotating switch located on the climate control panel turns the rear wiper On or Off. Pressing the rotating switch inward activates the rear window washer. Rotating the switch will enable one of five intermittent delay times for the rear wiper.
Page 250: Rear Window Defrosting
250 INSTRUMENT PANEL AND CONTROLS If the rear wiper is operating when the ignition is turned off, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume operation. Rear Window Defrosting A push-button type switch is located in the climate control panel.
Page 251: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 255 Automatic Transmission ....255 Normal Starting .
Page 252 252 STARTING AND OPERATING Electronic Brake Control System ... . 279 ABS (Anti-Lock Brake System) ... . 279 BAS (Brake Assist System) ....280 TCS (Traction Control System) .
Page 253 Snow Tires ......306 Tire Rotation Recommendations ... . 306 Tire Pressure Monitor System (TPMS) —...
Page 254 Snowplow ......338 Dodge Durango Or Chrysler Aspen Models . . 338 Recreational Towing (Behind Motorhome, Etc.) . . 339 Recreational Towing 2WD Models .
Page 255: Starting Procedures
STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belts. WARNING! Be sure to turn off the engine if you want to rest or sleep in your car. Accidents can be caused by inad- vertently moving the gear selection lever or by pressing the accelerator pedal.
Page 256 256 STARTING AND OPERATING ’Start’ position until the vehicle starts, but can release the key (still in the ignition) and the vehicle will continue through the start cycle. • Turn the ignition key to the START position, until the start motor engages. •...
Page 257: Engine Block Heater - If Equipped
WARNING! Do not attempt to push or tow your vehicle to get it started. Vehicles equipped with an automatic trans- mission cannot be started this way. Unburned fuel could enter the catalytic converter and once the engine has started, ignite and damage the converter and vehicle.
Page 258: Automatic Transmission
258 STARTING AND OPERATING The 4.7L engine block heater cord is located at the front of the engine compartment near the radiator cap. The 5.7L engine block heater cord is located on the left side of the engine compartment and rearward of the power distri- bution center.
Page 259 “P” Park Supplements parking brake by locking the transmission. Engine can be started in this range. Never use Park while vehicle is in motion. Apply parking brake when leaving vehicle in this range. Always apply parking brake first, then place selector in Park position. WARNING! Your vehicle could move and injure you and others if it is not completely in P (Park).
Page 260 260 STARTING AND OPERATING WARNING! It is dangerous to shift the selector lever out of “P” or “N” if the engine speed is higher than idle speed. If your foot is not firmly on the brake pedal, the vehicle could accelerate quickly forward or in re- verse.
Page 261 “1” First For driving up very steep hills and for engine braking at low speeds 25 mph (40 km/h) or less when going down hill. To prevent excessive engine speed do not exceed 25 mph (40 km/h) in this range. Overdrive Operation The overdrive automatic transmission contains an elec- tronically controlled fourth and fifth (if equipped) speed...
Page 262 262 STARTING AND OPERATING The transmission will downshift from Overdrive to Drive if the accelerator pedal is fully depressed at vehicle speeds above approximately 35 mph (56 km/h). When To Use “TOW/HAUL” Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the “TOW/HAUL”...
Page 263: Four-Wheel Drive Operation
light throttle. It engages at higher speeds under heavier acceleration. This may result in a slightly different feeling or response during normal operation in high gear. When the vehicle speed drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages.
Page 264 264 STARTING AND OPERATING When additional traction is required, the transfer case 4WD LOCK position can be used to lock the front and rear driveshafts together and force the front and rear wheels to rotate at the same speed. This is accomplished by rotating the 4WD Control Switch to the 4WD LOCK position - see Shifting Procedure section for specific shifting instructions.
Page 265 shift to take place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case. Proper operation of four-wheel-drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the transfer case.
Page 266: Shifting Procedure - Nv 144 Transfer Case
266 STARTING AND OPERATING Shifting Procedure - NV 144 Transfer Case 4WD to 4WD LOCK or 4WD LOCK to 4WD With the key ON and the engine either OFF or RUN- NING, rotate the transfer case switch, located on the instrument panel to the desired position.
Page 267: Nv 244 Generation Ii Transfer Case Operating Information / Precautions
If the key is not ON then the shift will not take place and no position indicator lights will be on or flashing. NV 244 Generation II Transfer Case Operating Information / Precautions The NV 244 Generation II is an electric shift transfer case and is operated by the 4WD Control Switch, which is located on the instrument panel.
Page 268 268 STARTING AND OPERATING NOTE: The transfer case Neutral (N) position is to be used for recreational towing only. See Recreational Tow- ing section for specific procedures on shifting into and out of Neutral (N). Transfer Case Position Indicator Lights Transfer case position indicator lights are located on the instrument cluster.
Page 269 When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 4WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 40 km/h (25 mph).
Page 270 270 STARTING AND OPERATING Normal Four-Wheel-Drive High Range - Employs inter- axle differential. Allows front and rear wheels to rotate at different speeds. All road surfaces. 4WD LOCK Four-Wheel-Drive Lock (4WD LOCK)- Locks the transfer case inter-axle differential. Forces front and rear wheels to rotate at the same speed.
Page 271: Shifting Procedure - Nv 244 Generation Ii
Shifting Procedure - NV 244 Generation II Transfer Case NOTE: The 4x4 system will not allow shifts between 4WD/ 4WD LOCK if the rear wheels are spinning (no traction). In this situation a position indicator light will flash and the original position indicator light will remain ON.
Page 272: Driving On Slippery Surfaces
272 STARTING AND OPERATING 3. While still rolling, rotate the transfer case control switch to the desired position. 4. After the position indicator light has stopped flashing, shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to complete stop. 2.
Page 273: Parking Brake
3. Replace tires when tread wear indicators first become visible. 4. Keep tires properly inflated. 5. Maintain sufficient distance between your vehicle and the car in front to avoid a collision in a sudden stop. PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel.
Page 274 274 STARTING AND OPERATING NOTE: The instrument cluster brake warning light indicates only that the parking brake is applied. You must be sure the parking brake is fully applied before leaving the vehicle. When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade.
Page 275: Brake System
BRAKE SYSTEM In the event power assist is lost for any reason, (for example, repeated brake applications with the engine off), the brakes will still function. The effort required to brake the vehicle will be significantly increased over that required with the power system operating. If either the front or rear hydraulic systems lose normal capability, the remaining system will still function with some loss of braking effectiveness.
Page 276 276 STARTING AND OPERATING At the instant one of the wheels is about to lock up, a slight pulsation can be felt in the brake pedal, indicating that the ABS is in the regulating mode. Keep firm and steady pressure on the brake pedal while experiencing the pulsation.
Page 277: Power Steering
WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded. •...
Page 278 278 STARTING AND OPERATING If for some reason, the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- tions you will observe a substantial increase in steering effort, especially at very low vehicle speeds and during parking maneuvers.
Page 279: Electronic Brake Control System
ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that includes ABS (Anti-Lock Brake System), BAS (Brake Assist System), TCS (Traction Con- trol System), ERM (Electronic Roll Mitigation), ESP (Elec- tronic Stability Program) and TSC (Trailer Sway Control). All six systems work together to enhance vehicle stability and control in various driving conditions, and are com- monly referred to as ESP.
Page 280: Bas (Brake Assist System)
280 STARTING AND OPERATING BAS (Brake Assist System) ESP Off Switch Location The BAS is designed to optimize the vehicle’s braking capability during emergency braking maneuvers. The system detects an emergency braking situation by sens- ing the rate and amount of brake application and then applies optimum pressure to the brakes.
Page 281: Tcs (Traction Control System)
WARNING! • BAS cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase braking efficiency beyond that afforded by the condition of the vehicle brakes and tires or the traction afforded. • The BAS cannot prevent accidents, including those resulting from excessive speed in turns, following another vehicle too closely, or hydro- planing.
Page 282: Erm (Electronic Roll Mitigation)
282 STARTING AND OPERATING ERM (Electronic Roll Mitigation) This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the speed of the vehicle. When ERM determines that the rate of change of the steering wheel angle and vehicles speed are sufficient to potentially cause wheel lift, it applies the appropriate brake and may reduce engine power to lessen the chance that wheel lift will occur.
Page 283: Esp (Electronic Stability Program)
ESP (Electronic Stability Program) This system enhances directional control and stability of the vehicle under various driving conditions. ESP cor- rects for over/under steering of the vehicle by applying the brake of the appropriate wheel to assist in counter- acting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the desired path.
Page 284 284 STARTING AND OPERATING WARNING! • ESP (Electronic Stability Program) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded. • ESP cannot prevent accidents, including those resulting from excessive speed in turns, or hydro- planing.
Page 285 conditions and more wheel spin than ESP would nor- mally allow is required to gain traction. TSC (Trailer Sway Control) is not available when the system is in the Partial Off mode. To turn ESP on again, momentarily depress the “ESP-Control OFF” Control Switch. This will restore the normal “ON”...
Page 286 286 STARTING AND OPERATING with off road driving but ESP function returns to provide the stability feature at speeds above 30 mph (48 km/h). The ABS is in a special Off-Road mode that allows wheels to lock at lower speeds if gravel is detected to shorten stopping distances.
Page 287: Multi Displacement System (Mds) - 5.7L Engine Only
several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed and corrected. NOTE: • The “ESP Indicator Light” and the “ESP/BAS Warning Lamp” come on momentarily each time the ignition switch is turned ON.
Page 288: Rocking The Vehicle
288 STARTING AND OPERATING ROCKING THE VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between FIRST and REVERSE, while applying slight pressure to the accelerator. The least amount of accelerator pedal pressure to main- tain the rocking motion without spinning the wheels or racing the engine is most effective.
Page 289 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
Page 290 290 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 291 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 292: Tire Identification Number (Tin)
292 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 293: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire Placard Location STARTING AND OPERATING 293 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 294 294 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the “Tire and Loading Information”...
Page 295 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 296 296 STARTING AND OPERATING...
Page 297: Tires - General Information
WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 298: Tire Inflation Pressures
298 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation, also increases tire rolling resistance and results in higher fuel consump- tion.
Page 299 CAUTION! After inspecting or adjusting the tire pressure, al- ways reinstall the valve stem cap (if equipped). This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Inflation pressures specified on the placard are always “cold tire inflation pressure.”...
Page 300: Radial-Ply Tires
300 STARTING AND OPERATING loading may be required for high-speed vehicle opera- tion. Refer to original equipment or an authorized tire dealer for recommended safe operating speeds, loading and cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi- mum load is dangerous.
Page 301: Compact Spare Tire - If Equipped
Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 302: Limited Use Spare - If Equipped
302 STARTING AND OPERATING Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly.
Page 303: Tread Wear Indicators
WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) for more than 30 seconds continuously when you are stuck, and don’t let anyone near a spinning wheel, no matter what the speed.
Page 304: Life Of Tire
304 STARTING AND OPERATING Life of Tire The service life of a tire is dependent upon varying factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years, regardless of the remaining tread.
Page 305: Alignment And Balance
WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of un- approved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle.
Page 306: Supplemental Tire Pressure Information - If Equipped
306 STARTING AND OPERATING Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION – IF EQUIPPED A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 307: Tire Pressure Monitor System (Tpms) - If Equipped
Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 308: Base System - If Equipped
308 STARTING AND OPERATING The TPM System will warn the driver of a low tire pressure if the tire pressure falls below the low pressure warning threshold for any reason, including low tem- perature effects. The TPM System will continue to warn the driver of low tire pressure as long as the condition exists, and will not turn off until the tire pressure is at or above recom- mended cold placard pressure.
Page 309 The Tire Pressure Monitoring Telltale Lamp will illuminate in the instrument cluster, and an au- dible chime will be activated when one or more of the four active road tire pressures are low. The audible chime will sound once every ignition cycle for each condition that it detects.
Page 310 310 STARTING AND OPERATING CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip- ment that is not of the same size, type, and/or style.
Page 311: General Information
• The TPMS is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the Tire Pressure Monitoring Telltale lamp. General Information This device complies with part 15 of the FCC rules and RSS 210 of Industry Canada.
Page 312: Reformulated Gasoline
312 STARTING AND OPERATING gasoline will provide no benefit over high quality regular and mid-grade gasolines, and in some circumstances may result in poorer performance. Light spark knock at low engine speeds is not harmful to your engine. However, continued heavy spark knock at high speeds can cause damage and immediate service is required.
Page 313: Mmt In Gasoline
CAUTION! DO NOT use gasoline containing Methanol or E85 Ethanol. Use of these blends may result in starting and driveability problems and may damage critical fuel system components. NOTE: 4.7L Engine — If Equipped , is now rated for E85 Ethanol use. Only vehicles with the E-85 fuel filler door label can operate on E-85.
Page 314: Materials Added To Fuel
314 STARTING AND OPERATING Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost. There- fore, you should not have to add anything to the fuel.
Page 315: Carbon Monoxide Warnings
NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessed against you. STARTING AND OPERATING 315 Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: •...
Page 316: Adding Fuel
316 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. NOTE: To avoid contact between fuel cap and paint, hang tether strap over hook provided on inner fuel door.
Page 317: Loose Fuel Filler Cap Message
WARNING! • Never have any smoking materials lit in or near the vehicle when the gas cap is removed or the tank filled. • Never add fuel when the engine is running. This is in violation of most state and federal fire regulations and will cause the malfunction indi- cator light to turn on.
Page 318: Flexible Fuel
318 STARTING AND OPERATING the problem is detected twice in a row, the system will turn on the Malfunction Indicator Light (MIL). Resolving the problem will turn the MIL light off. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler cap (gas cap).
Page 319: Ethanol Fuel (E-85)
CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 320: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
320 STARTING AND OPERATING NOTE: When the ambient temperature is above 90°F, you may experience hard starting and rough idle follow- ing start up even if the above recommendations are followed. Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) and Gasoline Vehicles Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline the engine oil requirements are the same.
Page 321: Maintenance
Maintenance If you operate the vehicle using E-85 fuel, follow Sched- ule B in the maintenance schedule section of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect drivability.
Page 322 322 STARTING AND OPERATING Hour of manufacture. The bar code that appears on the bottom of the label is your Vehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total permissible weight of your vehicle including driver, passengers, vehicle, options, and cargo. The label also specifies maximum capacities of front and rear axle systems.
Page 323: Curb Weight
Curb Weight The curb weight of a vehicle is defined as the total weight of the vehicle with all fluids, including vehicle fuel, at full capacity conditions, and with no occupants or cargo loaded into the vehicle. The front and rear curb weight values are determined by weighing your vehicle on a commercial scale before any occupants or cargo are added.
Page 324 324 STARTING AND OPERATING WARNING! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control.
Page 325: Trailer Towing
TRAILER TOWING In this section you will find safety tips and information on limits to the type of towing you can reasonably do with your vehicle. Before towing a trailer carefully re- view this information to tow your load as efficiently and safely as possible.
Page 326 326 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) The GAWR is the maximum capacity of the front and rear axles. Distribute the load over the front and rear axles evenly. Make sure that you do not exceed either front or rear GAWR.
Page 327 • Trailer Sway Control – Mechanical The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling.
Page 328 328 STARTING AND OPERATING WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
Page 329: Trailer Hitch Classification
Improper Adjustment of Weight Distributing System Fifth-Wheel Hitch A special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. Connects a vehicle and fifth-wheel trailer with a coupling king pin. STARTING AND OPERATING 329 Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm...
Page 330: Trailer Towing Weights (Maximum Trailer Weight Ratings)
330 STARTING AND OPERATING Weight Ratings)” for the website address that contains the necessary information for your specific drivetrain. Trailer Hitch Classification Class (Gross Trailer Wt.) Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium 3,500 lbs (1587 kg) Duty Class III - Heavy Duty 5,000 lbs (2268 kg)
Page 331: Towing Requirements
Never exceed the maximum tongue weight stamped on your bumper or trailer hitch. Consider the following items when computing the weight on the rear axle of the vehicle: • The tongue weight of the trailer. STARTING AND OPERATING 331 • The weight of any other type of cargo or equipment put in or on your vehicle.
Page 332 332 STARTING AND OPERATING CAUTION! • Avoid towing a trailer for the first 500 miles (805 km) of vehicle operation. Doing so may damage your vehicle. • During the first 500 miles (805 km) of trailer towing, limit your speed to 50 mph (80 km/h). Perform the maintenance listed in Section 8 of this manual.
Page 333 • Safety chains must always be used between your vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the chains under the trailer tongue and allow enough slack for turning corners. •...
Page 334 334 STARTING AND OPERATING − Check for signs of tire wear or visible tire damage before towing a trailer. Refer to the Tires–General Information section of this manual on Tread Wear Indicators for the proper inspection procedure. − When replacing tires refer to the Tires–General Infor- mation section of this manual on Replacement Tires for proper tire replacement procedures.
Page 335 WARNING! Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail. You might not have brakes when you need them and could have an accident. Towing any trailer will increase your stopping dis- tance.
Page 336: Towing Tips
336 STARTING AND OPERATING 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy traffic. If using a manual transmission vehicle for trailer towing, all starts must be in FIRST gear to avoid excessive clutch slippage.
Page 337 NOTE: Check the automatic transmission fluid level before towing. Towing Tips — Tow/Haul (If Equipped) To reduce potential for automatic transmission overheat- ing, turn the “TOW HAUL” feature ON when driving in hilly areas or shift the transmission to Drive position 2 on more severe grades.
Page 338: Snowplow
338 STARTING AND OPERATING SNOWPLOW Dodge Durango or Chrysler Aspen Models NOTE: Do not use Dodge Durango or Chrysler Aspen Models for snowplow applications. WARNING! Snowplows, winches, and other aftermarket equip- ment should not be added to the front end or your vehicle.
Page 339: Recreational Towing (Behind Motorhome, Etc.)
RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Recreational Towing 2WD Models Recreational towing of 2WD models is not allowable. Towing the vehicle with the transmission in Neutral can cause severe transmission damage. Removal of the drive- shaft for towing is not recommended since this allows transmission fluid to leak out.
Page 340 340 STARTING AND OPERATING NOTE: The NV 244 Generation II transfer case must be shifted into Neutral (N) for recreational towing. The Neutral (N) selection button is located on the lower left hand corner of the 4WD Control Switch. Shifts into and out of transfer case Neutral (N) can take place with the selector switch in any mode position.
Page 341 11. Repeat steps 9 and 10 with the transmission in Drive (D). 12. Turn ignition key to the unlocked OFF position. 13. Shift automatic transmission into Park (P). 14. Attach vehicle to tow vehicle with tow bar. NOTE: Items 1 through 5 are requirements that must be met prior to depressing the Neutral (N) selection button, and must continue to be met until the 4 seconds elaspes and the shift has been completed.
Page 342 342 STARTING AND OPERATING 3. Turn the ignition key to the ON position without starting the engine. 4. Depress brake pedal. 5. Shift automatic transmission to Neutral (N). 6. Using the point of a ballpoint pen or similar object, depress the recessed transfer case Neutral (N) button for 1 second.
Page 343: Equipment Identification Plate
CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage internal parts. STARTING AND OPERATING 343 EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood...
Page 345: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....346 Jacking And Tire Changing ....347 Jack Location .
Page 346: Hazard Warning Flasher
346 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHER The flasher switch is on the top of the steering column, just behind the steering wheel. Press the flasher switch and all front and rear directional signals will flash intermittently. Press the switch a second time to turn off the emergency flashers.
Page 347: Jacking And Tire Changing
JACKING AND TIRE CHANGING WARNING! • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 348: Jacking Instructions
348 WHAT TO DO IN EMERGENCIES JACKING INSTRUCTIONS Removing The Spare Tire The spare tire on your vehicle is located underneath the vehicle in the rear. Remove the spare tire before attempting to jack the truck. 1. Remove the rubber plug from the floor in the cargo area.
Page 349: Tire Changing Procedure
It is recommended that you stow the flat or spare to avoid tangling the loose cable. CAUTION! The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
Page 350 350 WHAT TO DO IN EMERGENCIES Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in PARK (automatic transmission). On Four Wheel Drive vehicles, shift the transfer case to the “4L” position.
Page 351 3. When changing a front wheel, place the jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame (prior to inboard transition. Operate the jack using the jack drive tube and the wheel wrench - the tube exten- sion, may be used but is not required.
Page 352 352 WHAT TO DO IN EMERGENCIES Rear Right Jacking Location Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
Page 353 WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack, tools and the extra tire and wheel in the places provided. 7. Remove wheel blocks. Do not install chrome or alu- minum wheel center caps on the spare wheel.
Page 354: Jump Starting Procedures
354 WHAT TO DO IN EMERGENCIES To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle.
Page 355 Check the Battery Test Indicator (if equipped). If a light or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1.
Page 356: Emergency Tow Hooks - If Equipped
356 WHAT TO DO IN EMERGENCIES WARNING! Do not connect the cable to the negative post of the discharge battery. The resulting electrical spark could cause the battery to explode. During cold weather when temperatures are below freezing point, electrolyte in a discharged battery may freeze.
Page 357: Towing A Disabled Vehicle
WARNING! Chains are not recommended for freeing a stuck vehicle. Chains may break, causing serious injury or death. WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. WHAT TO DO IN EMERGENCIES 357 CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road.
Page 358: Four-Wheel Drive Vehicles
358 WHAT TO DO IN EMERGENCIES Four-Wheel Drive Vehicles The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of the vehicle raised and the opposite end on a towing dolly. Two-Wheel Drive Vehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF...
Page 359: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment 4.7L V-8 ....362 Engine Compartment 5.7L HEMI V-8 ..363 Onboard Diagnostic System — OBD II ..364 Loose Fuel Filler Cap Message .
Page 360 360 MAINTAINING YOUR VEHICLE Power Steering — Fluid Check ... . 377 Front Suspension Ball Joints ....377 Drive Shaft Constant Velocity Joints .
Page 361 Center High-Mounted Stoplight ... 412 Fog Lights ......413 Fluids And Capacities .
Page 362: Engine Compartment 4.7L V-8
362 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 4.7L V-8...
Page 363: Engine Compartment 5.7L Hemi V-8
MAINTAINING YOUR VEHICLE 363 ENGINE COMPARTMENT 5.7L HEMI V-8...
Page 364: Onboard Diagnostic System - Obd Ii
364 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 365: Emissions Inspection And Maintenance Programs
cap until a clicking sound is heard. This is an indication that the gas cap is properly tightened. Press the odometer reset button to turn the message off. If the problem persists, the message will appear the next time the vehicle is started.
Page 366: Replacement Parts
366 MAINTAINING YOUR VEHICLE 3. As soon as you turn your key to the ON position, you will see your MIL symbol come on as part of a normal bulb check. 4. Approximately 15 seconds later, one of two things will happen: a.
Page 367: Dealer Service
DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 368: Engine Oil
368 MAINTAINING YOUR VEHICLE could adversely affect the engine or vehicle performance. These items should be inspected if a malfunction is observed or suspected. Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
Page 369 Change Engine Oil Road conditions and your style of driving affect the interval at which your oil should be changed. Check the following to determine if ANY apply to you: • Day or night temperatures are below 32°F (0°C). • Stop and Go driving. •...
Page 370 370 MAINTAINING YOUR VEHICLE Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner and the crankcase inlet air cleaner. The crankcase ventilation system should also be checked periodically.
Page 371: Engine Oil Filter
Lubricants which do not have both, the engine oil certi- fication mark and the correct SAE viscosity grade num- ber should not be used. Synthetic Engine Oils You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- mended maintenance intervals for oil and filter changes are followed.
Page 372: Drive Belts - Check Condition And Tension
372 MAINTAINING YOUR VEHICLE Drive Belts — Check Condition and Tension Belt tension is controlled by means of an automatic tensioner. No belt tension adjustments are required. However, belt and belt tensioner condition should be inspected at the specified intervals, and replaced if re- quired.
Page 373: Engine Air Cleaner Filter
Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe con- ditions, the filter element should be inspected periodi- cally and replaced if necessary at the intervals shown on Schedule “B”.
Page 374 374 MAINTAINING YOUR VEHICLE CAUTION! Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involv- ing engine misfire or other apparent loss of perfor- mance, have your vehicle serviced promptly. Contin- ued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and the...
Page 375: Maintenance Free Battery
To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in motion. • Do not try to start engine by pushing or towing the vehicle.
Page 376: Air Conditioner Maintenance
376 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
Page 377: Power Steering - Fluid Check
Refrigerant Recovery and Recycling R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- ever, the manufacturer recommends that air conditioning service be performed by dealers or other service facilities using recovery and recycling equipment.
Page 378: Drive Shaft Constant Velocity Joints
378 MAINTAINING YOUR VEHICLE Drive Shaft Constant Velocity Joints All four wheel drive models are equipped with four constant velocity joints. Periodic lubrication of these joints is not required. However, the joint boot should be inspected for external leakage or damage periodically. If external leakage or damage is evident, the joint boot and grease should be replaced immediately.
Page 379: Windshield Washers
Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with petroleum products such as engine oil, gasoline, etc. Windshield Washers The fluid reservoir should be checked for fluid level at regular intervals.
Page 380: Exhaust System
380 MAINTAINING YOUR VEHICLE Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the com- plete exhaust system and adjacent body areas for broken,...
Page 381: Cooling System
Cooling System WARNING! You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, don’t open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radia- tor is hot.
Page 382 382 MAINTAINING YOUR VEHICLE Cooling System — Drain, Flush and Refill At the intervals shown on the Maintenance Schedules, the system should be drained, flushed and refilled. If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner.
Page 383 Adding Coolant Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This coolant can be used up to 5 Years or 100,000 miles before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same coolant throughout the life of your vehicle.
Page 384 384 MAINTAINING YOUR VEHICLE WARNING! • The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine.
Page 385 When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points To Remember NOTE: When the vehicle is stopped after a few miles (a few kilometers) of operation, you may observe vapor coming from the front of the engine compartment.
Page 386: Emission Related Components
386 MAINTAINING YOUR VEHICLE • Do not change the thermostat for summer or winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions. Emission Related Components Fuel System Hoses And Vapor/Vacuum Harnesses When the vehicle is serviced for scheduled maintenance,...
Page 387: Brake System
Positive Crankcase Ventilation (PCV) Valve Proper operation of the crankcase ventilation system requires that the PCV valve be free of sticking or plug- ging because of deposits. Deposits can accumulate in the PCV valve and passage with increasing mileage. Have the PCV valve, hoses, and passages checked for proper operation at the intervals specified.
Page 388 388 MAINTAINING YOUR VEHICLE WARNING! Use of brake fluid that may have a lower initial boiling point, or is unidentified, as to specifications may result in sudden brake failure during hard prolonged braking. You could have an accident. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching on fire.
Page 389: Automatic Transmission
WARNING! Worn brake hoses can burst and cause brake failure. You could have an accident. If you see any sign of cracking, scuffing, or worn spots, have the brake hoses replaced immediately. Automatic Transmission Fluid Level Check Check the fluid level while the transmission is at normal operating temperature 180°F (82°C).
Page 390 390 MAINTAINING YOUR VEHICLE a minimum of two (2) minutes for the oil to fully drain into the transmission before rechecking the fluid level. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD”...
Page 391: Transfer Case
CAUTION! Using a transmission fluid other than the manufac- turers recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than the manufacturers recommended fluid will result in more frequent fluid and filter changes. Refer to Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 392: Axles
392 MAINTAINING YOUR VEHICLE Axles Refer to Fluids, Lubricants and Genuine Parts for correct fluid type. The manufacturer does not recommend regularly sched- uled oil changes for axles in vehicles whose operation is classified as normal truck service. NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components.
Page 393: Appearance Care And Protection From Corrosion
be used for chassis lubrication. Use only those greases that have the NLGI symbol on the container along with the proper quality level for your application. Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 394 394 MAINTAINING YOUR VEHICLE • Use Mopar auto polish to remove road film and stains and to polish your vehicle. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.
Page 395 • Use Mopar touch up paint on scratches as soon as possible. Your dealer has touch up paint to match the color of your vehicle. Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 396 396 MAINTAINING YOUR VEHICLE Mopar Total Clean is specifically recommended for leather upholstery. Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth.
Page 397 Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer.
Page 398: Fuse Block
398 MAINTAINING YOUR VEHICLE FUSE BLOCK CAUTION! When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system overload. If a properly rated fuse continues to blow, it suggests a problem in the circuit that must be corrected.
Page 399 MAINTAINING YOUR VEHICLE 399 Cavity Mini Fuse/Color Description Instrument Cluster 15 Amp Blue Battery Feed 10 Amp Red Ignition Run/Start for Next Generation Con- troller (NGC), Inte- 10 Amp Red grated Power Module (IPM), AC Relay and Fuel Pump Relay Door Node and Non- 10 Amp Red Memory Power Mirror...
Page 400 400 MAINTAINING YOUR VEHICLE Ignition Run/Start for 10 Amp Red Satellite Digital Audio 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow 10 Amp Red Module/Heated Rear ABS Module Ignition 10 Amp Red Cluster/Transfer Case/Seat Sw. Back lighting Receiver (SDAR)/ Digital Video Disc...
Page 401: Fuses (Power Distribution Center)
Fuses (Power Distribution Center) Power Distribution Center Your vehicle is equipped with an electrical power distri- bution center located in the left side of the engine compartment. This center contains cartridge fuses, mini fuses and relays. A description of each fuse and component may be MAINTAINING YOUR VEHICLE 401 stamped on the inside cover otherwise the cavity number of each fuse is stamped on the inside cover that corre-...
Page 402 402 MAINTAINING YOUR VEHICLE Cartridge Cavity Fuse / Mini Fuse Relay 40 Amp Blower Motor Relay Green Feed 40 Amp JB Feed Acc Delay Green Spare 30 Amp Pink 40 Amp Power Liftgate ( If Green Equipped) 40 Amp JB Feed / Heated Green Rear Glass (EBL)/ T Case Brake...
Page 403 Cartridge Cavity Fuse / Mini Fuse Description Relay 20 Amp Trailer Tow Yellow 15 Amp A/C Clutch Blue 15 Amp Stop Lamp Switch Blue Spare 20 Amp Run/Start Relay Feed Yellow Spare Relay Run Start Relay Run Remote Spare Relay Starter MAINTAINING YOUR VEHICLE 403 Cartridge...
Page 404: Fuses (Integrated Power Module)
404 MAINTAINING YOUR VEHICLE Fuses (Integrated Power Module) Integrated Power Module An integrated Power Module is located in the left side of the engine compartment. This center contains cartridge fuses, mini fuses and relays. A description of each fuse and component may be stamped on the inside cover otherwise the cavity number of each fuse is stamped on the inside cover that corresponds to the following chart.
Page 405 Cartridge Cavity Fuse / Mini Fuse Description Relay 10 Amp Rt Park Lamps Relay Radiator Fan Hi Rly 20 Amp Front Control Module Yellow (FCM) Batt #4 20 Amp Front Control Module Yellow (FCM) Batt #2 20 Amp Adjustable Pedal Yellow 20 Amp Ft Fog Lamps...
Page 406: Vehicle Storage
406 MAINTAINING YOUR VEHICLE Cartridge Cavity Fuse / Mini Fuse Relay 30 Amp Ignition Off Draw Green (IOD) #1 30 Amp Ignition Off Draw Green (IOD) #2 Spare Spare VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we Description recommend that you take the following steps to mini- mize the drain on your vehicle’s battery:...
Page 407: Replacement Light Bulbs
REPLACEMENT LIGHT BULBS LIGHT BULBS — Interior Dome Light ......WL212–2 Liftgate Lamp ......567 Overhead Console Lights .
Page 408 408 MAINTAINING YOUR VEHICLE 2. Remove one nut that attaches the headlight to the inner fender panel. Access to the nut is possible by opening the fender panel access door which is located in the wheel liner. 3. Grasp the headlight and pull firmly to disengage the headlight from the fender panel.
Page 409: Tail Lights, Turn Signals And Backup Lights - Replacement
Tail Lights, Turn Signals And Backup Lights — Replacement 1. Remove the two push-pins from the tail light housing. MAINTAINING YOUR VEHICLE 409 2. Rotate the light to the outboard side of the vehicle and remove.
Page 410 410 MAINTAINING YOUR VEHICLE 3. Unlock and remove electrical connector. 4. Twist bulb sockets counterclockwise to remove from housing. 5. Remove the bulbs from the bulb sockets by pulling the bulb straight out.
Page 411: License Lights
License Lights 1. Push tab towards the lamp and remove lamp assem- bly. MAINTAINING YOUR VEHICLE 411 2. Rotate the socket 1/4 turn counterclockwise. 3. Pull bulb from socket.
Page 412: Center High-Mounted Stoplight
412 MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight 1. Remove two screws securing stoplight housing assem- bly to the liftgate. 3. Pull bulb straight from socket to remove. 2. Turn socket 1/4 counterclockwise and free from hous- ing.
Page 413: Fog Lights
Fog Lights 1 – (3) Wheel liner screws 2 – (1) Air dam screw To replace the left foglamp bulb: 1. Remove the three wheel liner screws MAINTAINING YOUR VEHICLE 413 2. Remove the remove the far left air dam screw at the bottom of the fascia.
Page 414: Fluids And Capacities
414 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Fuel 4.7L, 87 Octane 5.7L, 89 Octane Engine Oil (with filter) 4.7L, SAE 5W-20, API Certified 5.7L, SAE 5W-20, API Certified Cooling System (includes 2.1 Qts./2L for coolant bottle 4.7L Engine(Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L Engine (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) NOTE: All fluid capacities are approximate.
Page 415: Fluids, Lubricants And Genuine Parts
FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) or equivalent. 4.7L Engine Oil Use SAE 5W-20, API Certified, meeting material standard MS-6395 or equiva- lent.
Page 416: Chassis
416 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Front Axle Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar ATF+4, Automatic Transmission Fluid. Mopar ATF+4, Automatic Transmission Fluid. SAE 75W-90 Multipurpose Type, GL-5 Gear Lubricant or equivalent. SAE 75W-140 Synthetic Gear Lubricant or equivalent.
Page 417 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..418 Maintenance Schedules ....418 Schedule “B” ......421 Schedule “A”...
Page 418: Emission Control System Maintenance
418 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type on the following pages must be done at the times or mileages specified to assure the continued proper func- tioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 419 • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual.
Page 420 420 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 421: Schedule "B" 421
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 422 422 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change front and rear axle fluid (4X4). Inspect engine air cleaner filter, replace if neces- sary.
Page 423 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change front and rear axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings.
Page 424 424 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change front and rear axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 425 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change front and rear axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs.
Page 426 426 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change front and rear axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 427 Miles (Kilometers ) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Change front and rear axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings.
Page 428 428 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Flush and replace engine coolant, if not replaced at 60 months.
Page 429 Miles (Kilometers) Change engine oil and engine oil filter, or at 3 months whichever comes first. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Change front and rear axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
Page 430 430 SCHEDULE “B” Miles (Kilometers) Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (170 000 km).
Page 431 Miles (Kilometers) Change engine oil and engine oil filter at in- terval shown or 3 months, whichever comes first. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Change front and rear axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
Page 432 432 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter at interval shown or 3 months, whichever comes first. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill transfer case fluid (4X4). Change front and rear axle fluid (4X4). Inspect brake linings.
Page 433 Miles (Kilometers) Drain and refill automatic transmission fluid and change main sump filter and spin-on cooler return filter if equipped. This applies only if your vehicle is used for police, taxi, fleet, or frequent trailer towing. Flush and replace engine coolant if not replaced at 120,000 miles (200 000 km).
Page 434: Schedule "A
434 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace as neces- sary.
Page 435 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and cor- rect stowage. Check transfer case fluid level (4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (170 000 km).
Page 436 436 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 437 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Check transfer case fluid (4X4). Flush and replace engine coolant, if not replaced at 60 months. Flush and replace engine coolant, if not replaced at 102,000 miles (170 000 km).
Page 438 438 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Rotate tires. Check spare tire for proper pressure and correct stowage. Drain and refill transfer case fluid (4X4). Flush and replace engine coolant, if not replaced at 120,000 miles (200 000 km).
Page 439 Inspection and service should also be performed anytime a malfunction is observed or suspected. Retain all re- ceipts. ** This Maintenance is recommended by the manufac- turer to the owner, but is not required to maintain the emissions warranty. SCHEDULE “A” 439 WARNING! You can be badly injured working on or around a motor vehicle.
Page 441: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......442 Prepare For The Appointment .
Page 442 We want you to be happy with our products and services. Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 443 technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. •...
Page 444 444 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni- cation Devices for the Deaf) equipment at its Customer Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY.
Page 445 WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and provisions of DaimlerChrysler’s warranties applicable to this vehicle. MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best.
Page 446 • Owner’s Manuals. These manuals have been prepared with the assistance of service and engineering specialists to acquaint you with specific Chrysler group vehicles. Included are starting, operating, emergency and maintenance pro- cedures as well as specifications, capabilities and safety tips.
Page 447 IF YOU NEED CONSUMER ASSISTANCE 447 Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals...
Page 449 INDEX...
Page 450 450 INDEX ABS (Anti-Lock Brake System) ... . 190,275 Adding Fuel ......316 Air Cleaner, Engine (Engine Air Cleaner Filter) .
Page 451 Axle Lubrication (Axle Fluid) ....392 Ball Joints ......377 Battery .
Page 452 452 INDEX Carbon Monoxide Warning ... . 72,161,315 Cargo Management System ....178 Cargo Organizer ..... . . 178 Cargo Organizer .
Page 453 Pressure Cap ......383 Radiator Cap ......383 Selection of Coolant (Antifreeze) .
Page 454 454 INDEX Emergency, In Case of Freeing Vehicle When Stuck ....288 Jacking ......349 Tow Hooks .
Page 455 Flashers Hazard Warning ..... . . 346 Turn Signal ..... 135,187,409 Flat Tire Stowage .
Page 456 456 INDEX Fuses ......172,398,401,404 Garage Door Opener (HomeLink ) ... 160 Gas Cap (Fuel Filler Cap) .
Page 457 Hitches Trailer Towing ......329 HomeLink (Garage Door Opener) Transmitter . . . 160 Hood Release ......129 Hoses .
Page 458 458 INDEX Lane Change and Turn Signals ..135,187,409 Lap/Shoulder Belts ..... 39,45 LATCH (Lower Anchors and Tether for CHildren) .
Page 459 Loading Vehicle ......321 Tires ....... 293 Locks .
Page 460 460 INDEX Mopar Parts ......366,445 Multi-Displacement Engine System ... 287 Multi-Function Control Lever .
Page 461 Pets ........71 Pets, Transporting ......71 Phone, Cellular .
Page 462 462 INDEX Rear Wiper/Washer ..... . 249 Rearview Mirrors ......79 Reclining Front Seats .
Page 463 Extender ......50 Front Seat ......39 Pretensioners .
Page 464 464 INDEX Speedometer ......189 Starting ....... 255 Automatic Transmission .
Page 465 Changing ......348 Compact Spare ......301 General Information .
Page 466 466 INDEX Trailer Weight ......330 Transaxle ......258 Automatic .
Page 467 Washer, Adding Fluid ....362,363 Washers, Windshield ..... 139 Washing Vehicle .
Page 468 NOTES...
Page 469 NOTES...
Page 470 NOTES...
Page 471 NOTES...
Page 472 NOTES...

Chrysler 2007 Aspen Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Instrument Panel and Controls

Starting and Operating

What to Do in Emergencies

Quick Links

INTRODUCTION

Chapters

Related Manuals for Chrysler 2007 Aspen

Summary of Contents for Chrysler 2007 Aspen