All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by MB/SaS/WS 1166 BU TV Consumer CarePrinted in the Netherlands...
2.1 Technical Specifications 2.2 Directions for Use Directions for use can be downloaded from the following 2.3 Connections websites: 2.4 Chassis Overview http://www.philips.com/support http://www.p4c.philips.com Notes: • Figures can deviate due to the different set executions. • Specifications are indicative (subject to change).
Page 3
Technical Specs, Diversity, and Connections TPM8.2A LA EN 3 Connections TV ANTENNA PC IN AUDIO HDMI 2 CVI 2/AV SERV.U Y/VIDEOPb HDMI 1 AV OUT VIDEO CVI 1 19160_001_110620.eps 110623 Figure 2-1 Connection overview Note: The following connector colour abbreviations are used 4 - Cinch: Video CVBS - In, Audio - In / 75 Ω...
Page 4
EN 4 TPM8.2A LA Technical Specs, Diversity, and Connections 14 - n.c. - Ground 15 - DDC_SCL DDC clock - Ground Red 16 - DDC_SDA DDC data - Ground Green 17 - Ground - Ground Blue 18 - +5V - +5V +5 V 19 - HPD Hot Plug Detect...
3.3.3 Spare Parts external damage. • Check the strain relief of the Mains/AC Power cord for For the latest spare part overview, consult your Philips Spare proper function. Part web portal. • Check the electrical DC resistance between the Mains/AC...
Page 6
EN 6 TPM8.2A LA Precautions, Notes, and Abbreviation List The third digit in the serial number (example: Abbreviation List AG2B0335000001) indicates the number of the alternative B.O.M. (Bill Of Materials) that has been used for producing the 0/6/12 SCART switch control signal on A/V specific TV set.
Page 7
6.5 MHz. L' is Band (VESA standard for communication I, L is all bands except for Band I channel and display). Using E-DDC, LG.Philips LCD (supplier) the video source can read the EDID Loudspeaker information form the display.
Page 8
SOPS Self Oscillating Power Supply Serial Peripheral Interface bus; a 4- wire synchronous serial data link standard S/PDIF Sony Philips Digital InterFace SRAM Static RAM Service Reference Protocol Small Signal Board Spread Spectrum Clocking, used to reduce the effects of EMI...
Mechanical Instructions TPM8.2A LA EN 9 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assembly/Panel Removal 4.4 Set Re-assembly Cable Dressing 19160_100_110620.eps 110620...
Page 10
EN 10 TPM8.2A LA Mechanical Instructions M5 × 10 3 × 16 M3 × 7 2 × 7 19160_101_110620.eps 110623 Figure 4-2 Rear cover removal 4.3.2 Small Signal Board (SSB) Refer to Figure 4-3 for details. Caution: it is mandatory to remount all different screws at their original position during re-assembly.
Page 11
Mechanical Instructions TPM8.2A LA EN 11 4. The PSU can be taken out of the set now. 4.3.4 Speakers 1. Unplug speaker connector from the SSB. 2. Release speaker cables from the clamps. 3. Take the speakers out. When defective, replace both units. 4.3.5 IR/LED Board 1.
EN 12 TPM8.2A LA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: • Display information (“SDM” or “SAM” indication in upper 5.1 Test Points right corner of screen, error buffer, software version, 5.2 Service Modes operating hours, options and option codes, sub menus).
Page 13
Service Modes, Error Codes, and Fault Finding TPM8.2A LA EN 13 Specifications • Press the following key sequence on the remote control • Set linear video and audio settings to 50%, but volume to transmitter: “062596” directly followed by the OK button to 25%.
Page 14
EN 14 TPM8.2A LA Service Modes, Error Codes, and Fault Finding Table 5-2 SAM mode overview Main Menu Sub-menu 1 Sub-menu 2 Description System Information Op Hour This represents the life timer. The timer counts normal operation hours, but does not count Stand-by hours.
Page 15
Service Modes, Error Codes, and Fault Finding TPM8.2A LA EN 15 • Line number for every • 1.3 Installation date Indicates the date of the first line (to make CSM language independent). installation of the TV. This date is acquired via time •...
Page 16
EN 16 TPM8.2A LA Service Modes, Error Codes, and Fault Finding Stepwise Start-up Standby Soft Mode Command Received, Switch previously in Standby Off(Mains Soft Mode (Power tact Standby Power Plug) switch) Digital Digital background background tasks started tasks completed TV Wakeup commands Received Standby...
Page 17
USB port. This allows replacement of a software image in a directly available. stand alone set. A description on how to upgrade the main 4. ComPair features TV software up possibilities. software can be found in the DFU or on the Philips website. Specifications 5.5.2 Introduction ComPair consists of a Windows based fault finding program and an interface box between PC and the (defective) product.
Page 18
EN 18 TPM8.2A LA Service Modes, Error Codes, and Fault Finding 5. To proceed, In next menu select [Start] and press OK to 5.5.6 Content and Usage of the One-Zip Software File start software updates. See Figure 5-9. 6. Upgrading will now begins and the status of the updating Below you find a content explanation of the One-Zip file, and progress will be displayed.
Page 19
Service Modes, Error Codes, and Fault Finding TPM8.2A LA EN 19 – ERROR: 6 0 0 0 0: Error code 6 is the last and only 5.8.1 NVM Editor detected error. – ERROR: 9 6 0 0 0: Error code 6 was detected first and In some cases, it can be convenient if one directly can change error code 9 is the last detected (newest) error.
EN 20 TPM8.2A LA Alignments 6. Alignments Index of this chapter: Table 6-1 White tone default settings 6.1 General Alignment Conditions 6.2 Hardware Alignments Colour temperature Screen 6.3 Software Alignments Picture mode size Green Blue 6.4 Option Settings Normal 32" 6.5 Reset of Repaired SSB (9000K) Cool (11000K) 32"...
Circuit Descriptions TPM8.2A LA EN 21 7. Circuit Descriptions Index of this chapter: • Only new circuits (circuits that are not published recently) 7.1 Introduction are described. 7.2 Power Supply • Figures can deviate slightly from the actual situation, due 7.3 Power Management to different set executions.
Page 22
EN 22 TPM8.2A LA Circuit Descriptions 7.1.3 SSB Cell Layout DC/DC DDR2 MT5366 AUDIO CLA SS TUNER DIGITAL I/O ANALOG I/O SERVICE CONNECTOR ANALOG I/O DIGITAL I/O 19160_206_110622.eps 110622 Figure 7-2 SSB layout cells (top view) 2011-Jun-24...
Page 23
The diversity in power supply units is mainly determined by the regular market. diversity in screen sizes, but please note to always order the Consult the Philips Service web portal for the order codes of the correct replacement. boards. Power Management...
Page 24
EN 24 TPM8.2A LA Circuit Descriptions Circuit Description DVDD3V3 7.4.1 System power R4103 R4103 R4104 R4104 R4105 R4105 C4104 C4104 The main board power is received at connector CN701 from power board, to receive the power and signals from the PSU. 220N16V 220N16V U4103...
Page 25
Circuit Descriptions TPM8.2A LA EN 25 7.4.6 Audio Amplifier (U602) The platform use I S to link audio amplifier IC. AMP_PWR Amp. GND DVDD3V3_AMP VDDLA VDDRA U602 U602 R648 R648 AMP_PLL# AOMCLK AD82587-LE48NAY AD82587-LE48NAY DVDD3V3_AMP MCLK 33R 1/16W 5% 33R 1/16W 5% CLK_OUT DGND DVDD...
Page 26
EN 26 TPM8.2A LA Circuit Descriptions 7.4.8 AV33 and DV33 (U701) The circuit around U701 will provide the main 3.3 V power supply to the SSB. 3V3 Main Power DVDD3V3 5V_SW 3V3_BUCK FB716 FB716 3V3_BUCK FB715 FB715 120R/3000mA 120R/3000mA C722 C722 120R/3000mA 120R/3000mA...
Page 27
Circuit Descriptions TPM8.2A LA EN 27 7.4.10 Demodulator MT5301B supports Full-HD MPEG1/2/4/DIVIX/VC1/RM/ Overall Features: H.264/AVS Video decoder standards, and JPEG. A 3D comb • Worldwide multi-standard analog TV demodulator. filter added to the TV decoder recovers great details for still •...
EN 28 TPM8.2A LA IC Data Sheets 8. IC Data Sheets This chapter shows the internal block diagrams and pin electrical diagrams (with the exception of “memory” and “logic” configurations of ICs that are drawn as “black boxes” in the ICs).
Page 29
IC Data Sheets TPM8.2A LA EN 29 Pinning information FSRC_WR 192 AVDD33_XTAL_STB GPIO14 191 XTALI VCC3IO 190 XTALO AVDD12_VPLL 189 AVDD33_DEMOD AE5P 188 AVSS33_DEMOD AE5N 187 AVSS12_DEMOD AE4P 186 AVDD33_IFPGA AE4N 185 ADCINN_DEMOD AE3P 184 ADCINP_DEMOD AE3N 183 AVDD12_DEMOD AECKP 182 AVDD33_CVBS AECKN 181 CVBS0P...
Page 30
EN 30 TPM8.2A LA IC Data Sheets Diagram Head Phone Out B16, TPA6132A2RTER (IC U606) Block diagram HPVDD TPA6132A2RTER Supply 2.2 F Control PGND HPVDD INL- Resistor OUTL Array INL+ Short-Circuit HPVSS Protection Thermal HPVDD Protection INR- Resistor OUTR Array INR+ HPVDD HPVSS...
Page 31
IC Data Sheets TPM8.2A LA EN 31 Diagram I2S Post Amplifier & SPIDF Out B17, AD82587 (IC U602) Block diagram AD82587 Pinning information VDDLA V DDRA N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. AD82587 MCLK N.C. CLK_OUT N.C. N.C.
Page 32
EN 32 TPM8.2A LA IC Data Sheets Diagram HDMI A & Switch 3:1 B09, TMDS361BPAGR (IC U501) Block diagram Dx+_1 TMDS Rx w/ AEQ Dx–_1 CLK+_1 TMDS Rx CLK–_1 Clock Detect VSadj SCL1 Dx+_SINK TMDS Tx Dx–_SINK SDA1 CLK+_SINK TMDS Tx CLK–_SINK Dx+_3 TMDS Rx...
Circuit Diagrams and PWB Layouts TPM8.2A LA EN 49 HDMI B & HDMI C (Side) HDMI B & HDMI C (Side) RXB_2+ Option for 3x port RXB_2+ CN502 CN502 RXB_2- RXB_2- RXB_0+ RXB_1+ TMDSD0+ RXB_1+ RXB_0- RXB_1- TMDSD0- RXB_1- RXB_1+ 5V_SW HD5V_B HDMI B (Rear#2) EDID EEPROM...
Circuit Diagrams and PWB Layouts TPM8.2A LA EN 56 S Post Amplifier & SPIDF Out S Post Amplifier & SPIDF Out switched by FB722 FB605 FB605 24V_12V_SW 18V4_BUCK AMP_PWR L601 L601 56UH 56UH AMP_RA ROUT+ SPK_R+ I2S Post Amp li fier 120R/3000mA 120R/3000mA AMP_PWR...
Circuit Diagrams and PWB Layouts TPM8.2A LA EN 58 Power MOSFET Switch Power MOSFET Switch Panel Log ic Pow er Contr ol 5VSB 5V_BUCK +12V LVDSVDD System Pow er Contr ol 5VSB 5V_SW FB711 FB711 FB712 FB712 FB713 FB713 FB707 FB707 NC/120R/6000mA NC/120R/6000mA...
Circuit Diagrams and PWB Layouts TPM8.2A LA EN 63 10-3 J 715G3866 IR Ebony LED & IR board LED & IR BE_5V 3V3_STBY BE_5V NC/0R05 1/16W 3V3_STBY LED2 100 OHM +-5% 1/16W Light Sensor KDR3T03AL 5.6K OHM 1/16W 4K7 1/16W 5% 10K 1/16W 5% NC/LED IR LED IR204-A...
Page 64
Circuit Diagrams and PWB Layouts TPM8.2A LA EN 64 LED & IR board layout Layout LED & IR Board (Top Side) LED1 LED2 Layout LED & IR Board (Bottom Side) TP12 TP11 2011-06-21 LED & IR board 715G3866 layout top/bottom 19160_528_110621.eps 110621 2011-Jun-24...
Page 65
Styling Sheets TPM8.2A LA EN 65 11. Styling Sheets 11-1 Ebony 32" Ebony 32" Pos No. Description Remarks BEZEL REAR COVER BASE ASSY 1176 REMOTE CONTROL FOR ELECTRICAL PARTS/ASSEMBLIES SEE WIRING DIAGRAM CHAPTER 9 19160_800_110620.eps 110622 2011-Jun-24...