Factory Mode - Philips 8601 Series Service Manual

5.1.3

Factory mode

Purpose
In Factory Mode you can perform extended alignments:
• Display and/or change Panel ID information.
• Display and/or change Tuner ID information.
• Clear Error buffer.
• Change several software alignment settings.
• Display testpattern.
• Reset Public Broadcasting Service password.
Table 5-2 Factory Mode Overview
Item Item value
0 F/W VERSION
1 PANEL_ID
2 DEMOD_TYPE
3 NVM ADDRESS
4 NVM VALUE
5 NVM STORE
6 COPY NVM to USB
7 COPY NVM to TV
8 TV Settings Key
9 TV Settings VALUE
10 TV Settings STORE
11 COPY TV Settings to USB
12 COPY TV Settings to TV
13 VIRGIN_MODE
14 ORT_MODE
15 DRMWARNING
16 AGEING MODE
17 COLOR TEMP MODE
18 CLR_TEMP_R
19 CLR_TEMP_G
20 CLR_TEMP_B
21 ADC_GAIN_R
22 ADC_GAIN_G
23 ADC_GAIN_B
24 ADC_OFFSET_R
25 ADC_OFFSET_G
26 ADC_OFFSET_B
27 AUD_GAIN_HDMI
28 AUD_GAIN_ATV
29 AUD_GAIN_DTV
30 AUD_GAIN_USB
31 AUD_GAIN_SPDIF
32 AUD_GAIN_LINE-IN
33 AQ_INDEX
34 Copy PQ to USB
35 Copy PQ to TV
36 Copy AQ to USB
37 Copy AQ to TV
38 COPY DB CHL to USB
39 COPY DB CHL to TV
40 LIGHT SENSOR TYPE
41 TEMP SENSOR TYPE
42 LED TYPE
43 AMBILIGHT TYPE
42 AMBILIGHT TYPE VALUE
44 3D
45 BLUETOOTH
46 ARC TEST
47 HDMI ARC OUTPUT ORDER
48 UART ENABLE
49 RESET MAC_ADDRESS
50 EXIT_FACTORY
Service Modes, Error Codes, and Fault Finding
Example Default value (65") Description
Press OK Displays: Software version of the supplier, Flash PQ, Smart Picture, BL Dimming, Source Meter, Picture Quality
checksum, Dimming library version, Flash AQ, AQ checksum, Model name, MTK version and NVM version.
See 6-3 Display Code Displays the Panel ID. Use left and right cursor to change the Panel ID, but keep in mind that selecting the wrong
.
Overview ID might result in not correct displaying the screen!
5 Choose demod type.
0 NVM address 0 to 8191. Use Item 6 to copy from and item 7 to store the data in the correct NVM address.
0 Displays the value at the NVM address of item 5
Press OK Use this option to save the data of item 6 to NVM address of item 5
Press OK Allows copying the TV settings to an USB stick, e.g. before replacing the SSB.
The TV settings ("Channel list", "Personal settings", "Option codes", "Display-related alignments" and "History list")
kept in the NVM are stored in two files.
1. The TV puts the two files in a folder REPAIR, which it created on a FAT formatted USB stick.
2. When the download on the USB stick failed, "Failure" will appear. In this case check if the USB stick is properly
connected.
Note: Uploading is of course only possible if software is running and if a picture is available.
Press OK Allows putting the NVM data stored on an USB stick to the TV set or to another SSB, e.g. after SSB replacement.
1. The TV set saves the two files previously created in its NVM.
2. If "USB to TV Success" is displayed, then unplug and plug power to restart the TV.
1 TV Settings Key
0 TV Settings VALUE
Press OK TV Settings STORE
Press OK COPY TV Settings to USB
Press OK COPY TV Settings to TV
Off Puts the TV set back in virgin mode, if not already (so in case the TV set has not been used yet).
On ORT mode
On Warning the data rights management
Off Use this for aging a new LCD panel
Normal Select color temperature mode: Normal - Cool - Warm.
0 Red colour temperature setting
0 Green colour temperature setting
0 Blue colour temperature setting
255 Red ADC gain
255 Green ADC gain
255 Blue ADC gain
127 Red ADC offset
127 Green ADC offset
127 Blue ADC offset
0 HDMI audio gain
12 Analogue TV audio gain
0 Digital TV audio gain
0 USB audio gain
0 SPDIF audio gain
0 Line-in audio gain
31 Audio Quality index
Press OK Saves the picture quality data to a file "pq.bin" to the root of a FAT formatted USB memory stick
Press OK Loads the picture quality data from a file "pq.bin" in to the TV
Press OK Loads the audio quality data from a file "AQ.bin" in to the TV
Press OK Loads the audio quality data from a file "AQ.bin" in to the TV
Press OK Copy the USB channel list to USB
Press OK Copy the TV channel list to TV
1 Light sensor type
3 Temperature sensor
0 The type of LED
Side Segments Select the type of AmbiLight: segments (side - top - bottom)
5 The type value of Ambient light
0 3D on/off
1 BLUETOOTH
On ARC test
EU ?
On Enables the UART
Press OK Resets the MAC-address
Press OK Exits the Factory mode
• Etc.
How to Activate the Factory mode
From the "menu/home", using the remote control, key in "1999"
and press button "Back/Return" (do not allow the display to
time out between key entries).
Factory Mode Overview
After entering the Factory mode, following items are displayed:
back to
div.table
QM15.1E LA 5. EN 25
2016-May-09