Sony DCR-HC19E Service Manual page 4

Table for differences of function
Model
Destination
Color system
Memory Stick Duo
A/V jack
DV Interface
Remote commander
Cradle (Handycam Station)
Model
Destination
Color system
Memory Stick Duo
A/V jack
DV Interface
Remote commander
Cradle (Handycam Station)
Note: DV Interface on the Cradle (Handycam Station)
• Abbreviation
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
JE : Tourist model
KR : Korean model
NE : North European model
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
DCR-HC17E/HC19E/HC21/HC21E/HC22E/HC32/HC32E/HC33/HC33E
DCR-HC17E DCR-HC19E
AEP, NE, EE AEP, UK, NE, EE
PAL
×
OUT
OUT
×
a (RMT-830)
×
DCR-HC32 DCR-HC32E
US, CND, E, KR, AEP, UK, NE, EE,
JE E, HK, AUS, JE
NTSC
a
IN/OUT
IN/OUT (Note) IN/OUT (Note)
a (RMT-831) a (RMT-831)
a
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
DCR-HC21
US, CND, E, KR,
BR
PAL NTSC
× ×
OUT OUT
OUT IN/OUT
a (RMT-830)
× ×
DCR-HC33
BR
PAL NTSC
a a
IN/OUT IN/OUT
IN/OUT (Note)
a (RMT-831)
a a
ATTENTION AU COMPOSANT AYANT RAPPORT
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270°C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
— 4 —
DCR-HC21E DCR-HC22E
E, HK, AUS, CH AEP, UK, NE, EE
PAL
×
OUT
IN/OUT IN/OUT (Note)
a (RMT-830) a (RMT-830)
×
DCR-HC33E
CH
PAL
a
IN/OUT
IN/OUT (Note)
a (RMT-831)
a
À LA SÉCURITÉ!
PAL
×
OUT
a