Page 1
Order No. MTV0501406C3 Colour Television TX-29P190T MD3N Chassis SPECIFICATIONS Specifications...
Page 2
Players and Special VCRs PAL 60 Hz/6.0 MHz PAL 60 Hz/6.5 MHz SECAM 60 Hz/5.5 MHz SECAM 60 Hz/6.0 MHz SECAM 60 Hz/6.5 MHz NTSC 50 Hz/4.5 MHz Receiving Channels Regular TV VHF BAND 2-12 (PAL/SECAM B, K1) 0-12 (PAL B AUST.) 1-9 (PAL B N.Z.) 1-12 (PAL/SECAM D) 1-12 (NTSC M Japan)
Page 3
Video, Audio L/R terminals AV2 IN (Front): S-Video, Video, Audio L/R RGB Terminals AV3 IN (Rear): Video, Audio L/R terminals AV4 IN (Rear): Video or Y/P B /P R , Audio L/R terminals RGB Input High-DENSITY D-sub 15 pin 31.5 kHz/60 Hz (640 x 480 dot) and 31.5 kHz/70 Hz (640 x 400 dot) Remote Control R6 (AA) Battery x 2...
Page 4
3. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers, shields and isolation R-C combinations, are properly installed. 4. When the receiver is not to be used for a long period of time, unplug the power cord from the AC outlet.
Page 5
exposed metallic part has a return path to the chassis, the reading should be between 4 M and 20 M . When the exposed metal does not have a return path to the chassis, the reading must be infinite. 1.3. Leakage Current Hot Check (See Fig. 1) 1.
Note: It is important to use an accurate periodically calibrated high voltage meter. / 1. Set the brightness to minimum. 2. Measure the High Voltage. The meter reading should indicate 31.0 ± 1 kV. If the meter indication is out of tolerance, immediate service and correction is required to prevent the possibility of premature component failure.
2.3. HOTEL MODE Purpose 1. At Hotels, this Mode prevents the customer from changing the TV preset data such as Channel preset data. / / Note: This Mode is useful for Hotels. You should not get into “Hotel mode” with Normal use. Operation 1.
hexadecimal code of the TV set. 2. To get into the Self-Check mode, press the down n [-/ ] button on the customer controls at the front of the set, at the same time pressing the HELP button on the remote control and the screen will show: 4.
Page 13
3. Set controls: CAP. BRT....CENTER COLOUR..CENTER CONTRAST..MAX AI....OFF Adjustment procedure 1. Adjust Sub Contrast (Service 1): A = 3.85 0.1V 2. Adjust Video gain 2 (Service 1) so that Sub picture level B becomes as same as Main picture level A. 5.4.
Page 14
2. Connect oscilloscope to A51 pin 50. 3. Set controls: BRT....CENTER COLOUR..CENTER CONTRAST..MAX NTSC TINT..CENTER AI....OFF Adjustment procedure 1. Adjust Sub NTSC Tint so that the peak of level of waveform is similar to Fig. 3 2. Receive the Rainbow pattern (3.58 MHz NTSC) on both of Main and Sub pictures.
5.5. SUB COLOUR Item / preparation 1. Receive a 3.58 MHz NTSC rainbow pattern. 2. Connect oscilloscope to A51 pin 48. 3. Set controls: BRT....CENTER COLOUR..CENTER CONTRAST..MAX AI....OFF Adjustment procedure 1. Adjust Sub Colour: A = 3.3 0.5V 5.6. VRS ADJUSTMENT 1.
Page 16
A. Set DY to CRT not to tilt up and down and left and right deflection. (Fig. 1) B. Set CY to CRT and set CY magnet primarily. / Pur Mg: Set Pur Mg that 2 magnets are vertical position. / VRS Mg: Set VRS Mg that 2 magnets are side position.
5.7. COLOUR PURITY 1. Operate the TV set for over 60 minutes. 2. Receive a purity pattern signal. (white pattern) 3. Set Bright and Contrast controls to their maximum positions. 4. Set V-POS to 63 DAC. 5. Adjust roughly the static convergence magnets. 6.
Page 18
10. Adjust roughly the Low Light controls and make sure that a uniform white field is obtained. 11. Tighten the clamp screw. 5.8. CONVERGENCE 1. INSTRUMENT A. Helmhortz device 2. PREPARATION A. Set the Helmhortz device to local magnetic field. / Horizontal: 0 ± 0.03 x10 B.
Page 19
B. YHC, YV, XV, Adjustment (Fig. 2) a. Adjust so that Static and Dynamic convergence is best with YHC, VR, YV and XV coil. / In case of static convergence is tilted, repeat (1) Static convergence Adjustment. C. Dynamic convergence Adjustment a.
Page 20
6. Set the data level of SUB BRIGHT, R, G, B-CUTOFF and R, G, B-DRIVE to the table values. - R High (R-CUT OFF) - 256 - G High (G-CUT OFF) - 512 - B High (B-CUT OFF) - 256 - R Low (R-DRIVE) - 128 - G Low (G-DRIVE) - 128 - B Low (B-DRIVE) - 128...
adjusment before adjusting anything. 8. Wedge A shown in Fig. 1 should be fixed within a range of 45° to the left of the vertical line as shown. 9. After inserting wedge A, insert wedges B, C and D. / The wedges should be set 90°...
Page 22
5. Degauss the CRT face. 6. Connect the photo sensors of the Colour Analyser to the CRT. Note: CRT cut off adjustment is completed. Adjustment procedure 1. Adjustment of Low Light Adjustment SUB BRIGHT, so that “Y” axis indicates 6.5 Adjustment R-CUT OFF, so that y axis indicates 0.248.
5.12. GEOMAGNETIC Item / preparation 1. Demagnetize the GM-Board around its perimeter with the Demagnetizer. 2. Set to control: Geomagnetic..Auto Adjustment procedure 1. Connect a DC voltage meter to TPGM1-2pin (GM-Board) 2. Adjust the R4863 (GM-Board) so that the Vx Out at TPGM1-2pin becomes 4.9 0.05 V 3.
Page 24
1. Receive PAL monoscope pattern. 2. Set scan mode to 100Hz by remote control key. 3. Adjust V-POS (100i / 4:3) so that the scale of the top and bottom side is equal. 6.1.1.2. 120i V-POS ADJUSTMENT 1. Receive NTSC monoscope pattern. 2.
3. Adjust V-AMP (100i / 4:3) so that B, D (Fig. 2) is 2.1 ± 0.1. 6.1.2.2. 120i V-AMP ADJUSTMENT 1. Receive NTSC monoscope pattern. 2. Set scan mode to 100 Hz by remote control key. 3. Adjust V-AMP (120i / 4:3) so that B, D (Fig. 2) is 2.1 ± 0.1. 6.1.2.3.
Page 26
2. Set scan mode to 100 Hz by remote control key. 3. Adjust H-POS (100i / 4:3) so that the horizontal position is center of CRT. 6.2.1.2. 120i H-POS ADJUSTMENT 1. Receive NTSC monoscope pattern. 2. Set scan mode to 100 Hz by remote control key. 3.
Page 27
4 by Trapezoid (100i / 4:3). 5. Confirm there is no H-parallel distortion. / If there is distortion, adjust by H-Parallel (100i / 4:3). / In that case, repeat 4 and 5 so that there is no trapezoid / parallel distortion. 6.
Page 28
1. Receive PAL cross-hatch pattern. 2. Set scan mode to progressive by remote control key. 3. Adjust the vertical line to straight by Parabola (50p / 4:3). 4. Adjust the vertical line to straight line of both sides vertical line in Fig. 5 by Trapezoid (50p / 4:3).
Page 29
6.4. V LINIALITY ADJUSTMENT / CONFIRMATION (4:3 MODE) 6.4.1. 100i V-Linear ADJUSTMENT 1. Receive PAL monoscope pattern. 2. Set scan mode to 100 Hz by remote control key. 3. Confirm V-linear (100i / 4:3) as to the balance of circle. / If needed, adjust V-linear (100i / 4:3).
Page 30
6.5. DEFLECTION (16:9 MODE) ADJUSTMENT / CONFIRMATION 6.5.1. DATA SETTING (16:9) 1. Copy the adjusted data of 100i / 4:3 mode to 100i / 16:9 in the table 1 (Except H-POS, V-S-Correct). 2. Copy the adjusted data of 120i / 4:3 mode to 120i / 16:9 in the table 1 (Except H-POS, V-S-Correct).
8. Set scan mode to 100 Hz. 9. Confirm that A, B in Fig. 7 is 5.0 cm ± 1 cm. If not, adjust V-AMP (120i / 16:9). 10. Set scan mode to progressive. 11. Confirm that A, B in Fig. 7 is 5.0 cm ± 1 cm. If not, adjust V-AMP (60p / 16:9).
Page 32
1. Adjust V-POS (VGA) so that center of the crosshatch pattern is center of the CRT. 6.8.2. V-HEIGHT ADJUSTMENT 1. Adjust V-AMP (VGA) so that A = B in Fig. 8. 6.8.3. H-CENTER ADJUSTMENT 1. Adjust H-POS (VGA) so that horizontal position is center of CRT. 6.8.4.
Page 33
6.9.1. V-CENTER ADJUSTMENT 1. Adjust V-POS (VGA 400) so that center of the crosshatch pattern is center of the CRT. 6.9.2. V-HEIGHT ADJUSTMENT 1. Adjust V-AMP (VGA 400) so that A = B in Fig. 10. 2. Add 10 dac to the above data and set to EEPROM [336]. 6.9.3.
Page 36
8.2. A BOARD 8.2.1. A BOARD 1/4 8.2.2. A BOARD 2/4 8.2.3. A BOARD 3/4 8.2.4. A BOARD 4/4 8.3. G BOARD 8.3.1. G BOARD 1/1 8.4. X BOARD 8.4.1. X BOARD 1/2 8.4.2. X BOARD 2/2 8.5. DG BOARD...
Page 38
10. Replacement Parts List 10.1. Replacement Parts List Notes...
Page 39
PICTURE TUBE EASG15S509A2 SPEAKER EUR511048 REMOTE CONTROL J0KG00000088 CORE CLAMPER KDY4UWH11F DEFLECTION YOKE KRCBC160928B CORE CLAMPER TBM4G1284 MODEL NAME PLATE TBM4G3011 PANASONIC BADGE TBX4G89111 POWER BUTTON TES4G406 COIL SPRING TES4G409-1 SPRING (DOOR) THT4G1011J SCREW (SPEAKER) THT4G10139 SCREW TJB1726400 75OHM ADAPTOR TKK4G8586-1...
Page 40
Ref. No. Part No. Part Name & Description Remarks TNP4G217AM L BOARD TNP4G235AH P BOARD TNP4G289AF H BOARD TNP4G290AL A BOARD TPD4G2099 CUSHION (BOTTOM) TPE4G14023 SET COVER TPE4G14024 TOP COVER TQB4G3967 FAN BAG TSMA011 MAGNET TSN63115-4 PURITY MAGNET TSX4G161H AC POWER CORD TXFKY01DR20 CABINET ASSY TXFPC01DR20...
Page 41
Ref. No. Part No. Part Name & Description Remarks C121 ECJ1VC1H100C C 10PF, C, 50V C1210 ECA1CM101B E 100UF, 16V C1211 ECJ1VF1H103Z C 0.01UF, Z, 50V C1215 ECJ2VF1E104Z C 0.1UF, Z, 25V C1216 ECJ2VF1E104Z C 0.1UF, Z, 25V C1230 ECEA1CN470U E 47UF, 16V C1231 F2A1C4710045...
Page 45
Ref. No. Part No. Part Name & Description Remarks C1401 ECJ1VB0J105K C 1UF, K,6.3V C1402 ECJ3YB0J335M C 3.3UF, M,6.3V C1403 ECJ1VB1H123K C 0.012UF, K, 50V C1404 EEEHB0G221P E 220UF, 4V C1405 ECJ1VB0J105K C 1UF, K,6.3V C1406 ECJ1VB0J105K C 1UF, K,6.3V C1410 ECJ1VB0J105K C 1UF, K,6.3V...
Page 51
Ref. No. Part No. Part Name & Description Remarks C3036 ECA1HM2R2B E 2.2UF, 50V C3037 ECJ1VC1H471J C 470PF, J, 50V C3038 ECA1HM2R2B E 2.2UF, 50V C3048 ECJ2VF1C105Z C 1UF, Z, 16V C3049 ECA1HM220B E 22UF, 50V C3050 ECA1CM101B E 100UF, 16V C3051 ECJ1VF1H104Z C 0.1UF, Z, 50V...
Page 53
Ref. No. Part No. Part Name & Description Remarks C373 ECJ1VB1H103K C 0.01UF, K, 50V C374 ECJ1VC1H100D C 10PF, D, 50V C375 ECQE2104KF P 0.1UF, K,250V C376 F1B2H561A025 C 560PF , 500V C377 ECA2EM100B E 10UF, 250V C380 ECA1HM101B E 100UF, 50V C383 ECA1CM222B E 2200UF, 16V...
Page 54
C581 ECWF2334JB P 0.33UF, J,250V Ref. No. Part No. Part Name & Description Remarks C582 ECWF2364JB P 0.36UF, J,250V C583 ECWF2364JB P 0.36UF, J,250V C584 ECWF2334JB P 0.33UF, J,250V C585 ECKR3A272KBP C 2700PF, K, 1KV C703 ECQE2334KF P 0.33UF, K,250V C705 ECKW3A272KBP C 2700PF, K, 1KV...
Page 55
Ref. No. Part No. Part Name & Description Remarks C885 EEUFC1C471LB E 470UF, 16V C886 ECA1CM101B E 100UF, 16V C888 ECJ1VF1H103Z C 0.01UF, Z, 50V C889 ECJ1VF1H103Z C 0.01UF, Z, 50V C892 ECKW3D152KBP C 1500PF, K, 2KV C897 ECQE6823KF P 0.082UF, K,630V C901 EEANA1E100B E 10UF, 25V...
Page 66
Ref. No. Part No. Part Name & Description Remarks R1109 ERJ3GEY0R00 M 0OHM,J,1/16W R1110 ERJ3GEYJ103 M 10KOHM,J,1/16W R1111 ERJ3GEYJ103 M 10KOHM,J,1/16W R1112 ERJ3GEYJ331 M 330OHM,J,1/16W R1113 ERJ3GEYJ331 M 330OHM,J,1/16W R1114 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1115 ERJ3GEYJ101 M 100OHM,J,1/16W R1116 ERJ3GEYJ101 M 100OHM,J,1/16W R1117 ERJ3GEYJ101 M 100OHM,J,1/16W...
Page 68
Ref. No. Part No. Part Name & Description Remarks R1169 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1170 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1171 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1172 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1173 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1174 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R1176 ERJ3GEYJ100 M 10OHM,J,1/16W R1178 ERJ3GEYJ100 M 10OHM,J,1/16W R1182 EXB38V680J M 68OHM,J,1/16W...
Page 72
Ref. No. Part No. Part Name & Description Remarks R1384 ERJ3GEYJ103 M 10KOHM,J,1/16W R1385 ERJ3GEYJ101 M 100OHM,J,1/16W R1386 ERJ3GEYJ102 M 1KOHM,J,1/16W R1387 ERJ3EKF1201 M 1.2KOHM,F,1/16W R1388 ERJ3EKF2801 M 2.8KOHM,F,1/16W R1389 ERJ3EKF1201 M 1.2KOHM,F,1/16W R1390 ERJ3GEYJ103 M 10KOHM,J,1/16W R1401 ERJ3GEYJ242 M 2.4KOHM,J,1/16W R1406 ERJ3GEYJ101 M 100OHM,J,1/16W...
Page 74
Ref. No. Part No. Part Name & Description Remarks R1465 ERJ3GEYJ333 M 33KOHM,J,1/16W R1466 ERJ3GEYJ333 M 33KOHM,J,1/16W R1467 ERJ3GEYJ333 M 33KOHM,J,1/16W R1468 ERJ3GEYJ103 M 10KOHM,J,1/16W R1469 ERJ3GEYJ333 M 33KOHM,J,1/16W R1473 ERJ3EKF75R0 M 75OHM,F,1/16W R1474 ERJ3EKF75R0 M 75OHM,F,1/16W R1475 ERJ3EKF75R0 M 75OHM,F,1/16W R1479 ERJ3GEY0R00 M 0OHM,J,1/16W...
Page 76
Ref. No. Part No. Part Name & Description Remarks R2104 ERJ3GEYJ103 M 10KOHM,J,1/16W R2105 ERJ3GEYJ103 M 10KOHM,J,1/16W R2110 ERJ3GEYJ101 M 100OHM,J,1/16W R2111 ERJ3GEYJ101 M 100OHM,J,1/16W R2112 ERJ3GEYJ222 M 2.2KOHM,J,1/16W R2113 ERJ3GEYJ222 M 2.2KOHM,J,1/16W R2114 ERJ3GEYJ222 M 2.2KOHM,J,1/16W R2115 ERJ3GEYJ101 M 100OHM,J,1/16W R2116 ERJ3GEYJ101 M 100OHM,J,1/16W...
Page 78
Ref. No. Part No. Part Name & Description Remarks R3031 ERJ3GEYJ223 M 22KOHM,J,1/16W R3032 ERJ3GEYJ471 M 470OHM,J,1/16W R3033 ERJ3GEYJ223 M 22KOHM,J,1/16W R3034 ERJ3GEYJ680 M 68OHM,J,1/16W R3035 ERJ3GEYJ181 M 180OHM,J,1/16W R3036 ERJ3GEYJ103 M 10KOHM,J,1/16W R3037 ERJ3GEYJ101 M 100OHM,J,1/16W R3038 ERJ3GEYJ101 M 100OHM,J,1/16W R3039 ERJ3GEYJ104 M 100KOHM,J,1/16W...
Page 80
Ref. No. Part No. Part Name & Description Remarks R3307 ERJ3GEYJ221 M 220OHM,J,1/16W R3308 ERJ3GEY0R00 M 0OHM,J,1/16W R3311 ERJ3GEY0R00 M 0OHM,J,1/16W R3312 ERJ3GEY0R00 M 0OHM,J,1/16W R3313 ERJ3GEY0R00 M 0OHM,J,1/16W R3314 ERJ3GEYJ750 M 75OHM,J,1/16W R3315 ERJ3GEYJ750 M 75OHM,J,1/16W R3316 ERJ3GEYJ750 M 75OHM,J,1/16W R3317 ERJ3GEY0R00 M 0OHM,J,1/16W...
Page 82
Ref. No. Part No. Part Name & Description Remarks R419 ERJ3GEYJ152 M 1.5KOHM,J,1/16W R451 ERDS1TJ1R5 C 1.5OHM,J, 1/2W R452 ERDS1TJ1R5 C 1.5OHM,J, 1/2W R453 ERJ3GEYJ393 M 39KOHM,J,1/16W R454 ERJ3GEYJ123 M 12KOHM,J,1/16W R455 ERJ3GEYJ101 M 100OHM,J,1/16W R456 ERG3FJ151H M 150OHM,J, 3W R457 ERJ3EKF7151 M7.15KOHM,F,1/16W...
Page 84
Ref. No. Part No. Part Name & Description Remarks R530 ERG3FJ472H M 4.7KOHM,J, 3W R531 ERDS2TJ222 C 2.2KOHM,J, 1/4W R532 ERDS2TJ222 C 2.2KOHM,J, 1/4W R533 ERDS2TJ153 C 15KOHM,J, 1/4W R534 ERDS2TJ272 C 2.7KOHM,J, 1/4W R535 D0AE912JA046 C 9.1KOHM,J, 1/4W R536 ERDS2TJ274 C 270KOHM,J, 1/4W R537...
Page 85
Ref. No. Part No. Part Name & Description Remarks R832 ERDS2TJ102 C 1KOHM,J, 1/4W R834 ERDS2TJ103 C 10KOHM,J, 1/4W R840 ERD75TAJ825 C 8.2MOHM,J, 3/4W R851 ERQ2CKR33 F 0.33OHM,K, 2W R853 D0D5R33KA007 W 0.33OHM,K, 5W R854 D0D5R33KA007 W 0.33OHM,K, 5W R858 ERJ3GEYJ472 M 4.7KOHM,J,1/16W R859...
Page 87
Ref. No. Part No. Part Name & Description Remarks TRANSFORMERS T501 ZTFN35002A FLYBACK TRANS T550 ETH19Y187AY H DRIVE TRANS T801 TLP4GA015D SWITCHING TRANS OTHERS K1KA10AA0191 CONNECTOR K1KB35BA0023 CONNECTOR K1KA09AA0190 CONNECTOR K1KA09AA0190 CONNECTOR TJS4G411 CONNECTOR K1KA05AA0190 CONNECTOR K1KA04AA0190 CONNECTOR K1KB16BA0016 CONNECTOR K1KB16BA0016 CONNECTOR TJS4G413...
Page 88
Ref. No. Part No. Part Name & Description Remarks JS1321 ERJ3GEY0R00 M 0OHM,J,1/16W JS1322 ERJ3GEY0R00 M 0OHM,J,1/16W JS1338 ERJ3GEY0R00 M 0OHM,J,1/16W JS1360 ERJ3GEY0R00 M 0OHM,J,1/16W JS1361 ERJ3GEY0R00 M 0OHM,J,1/16W JS1362 ERJ3GEY0R00 M 0OHM,J,1/16W JS1370 ERJ3GEY0R00 M 0OHM,J,1/16W JS1371 ERJ3GEY0R00 M 0OHM,J,1/16W JS1372 ERJ3GEY0R00 M 0OHM,J,1/16W...