In the interests of user safety (required by safety regulations in some countries) the set should be re- stored to its original condition and only parts identi- cal to those specified should be used. In order to service the model 32LW-92H , refer to AK-45 Chassis Service Manual (SE00AK45CHA00).
Page 2
32LW-92H SERVICE MANUAL UPDATE LOG SHEET Technical Report No. Application Cause / Solution Part No. Page No. Data /Serial No. Technical Bulletin No. Use this page to keep any special servicing information as Technical Report (Bulletin), Technical Information, etc. If only part number changes are required, just change part number directly the part number in the Parts Listing Section.
32LW-92H IMPORTANT SERVICING NOTES Only qualified service personnel are allowed to carry out maintenance and repair of this receiver. Servicing of High Voltage System and CRT It is important that the static charge is removed from the high voltage system when carrying out work on the receiver.
32LW-92H CONTROLS & TERMINALS FRONT PANEL 3&+ REAR PANEL (;7 (;7 )5217 $9 )$9 Speakers (left + right) VIDEO ( )= VCR = Power On / Off = Headphone 3,6 mm Ø + = Volume -/+ ANT = Antenna (75 W) - P/CH + = Program -/+ EXT.1 = Scart Socket 1 (with RGB)
Page 6
32LW-92H REMOTE CONTROL = Stand By = Cursor Up = Cursor Right OK = OK Info (Program Menu) 0 - 9 = Direct Program -/-- = Double Digit Wide mode button P/CH+ = Program + + = Volume + = TV / Quit Menu...
Page 7
32LW-92H CHASSIS LAYOUT Mother Unit CRT Unit Control Panel Unit Remote Control Unit...
32LW-92H PARTS LISTING REF No. PARTS DESCRIPTION SN CODE EX CODE D108 30001315 DIODE BYD33D 1A/200V 20A REPLACEMENT PARTS D110 30001288 DIODE BYV27-200 2A/200V 50A Replacement parts which have special safety characteristics are identified in D111 30001318 DIODE BA159 1A/800V 20A this manual.
Page 9
32LW-92H REF No. PARTS DESCRIPTION SN CODE EX CODE REF No. PARTS DESCRIPTION SN CODE EX CODE C155 30000375 CAP EL 220UF 16V M L500 30001992 FIXED COIL 10UH Q65 K-A L501 30001992 FIXED COIL 10UH Q65 K-A C160 30000076 CAP MKT SAFE 100NF 275V M AC C161 30000440 CAP CER SAFE 2.2NF 4KV M...
Page 10
32LW-92H REF No. PARTS DESCRIPTION SN CODE EX CODE REF No. PARTS DESCRIPTION SN CODE EX CODE R221 30000792 RES CF 1/4W 75R J C724 30000345 CAP EL 10UF 50V M C735 30000393 CAP EL 3.3UF 50V M R231 30000792 RES CF 1/4W 75R J...
PL106 30001830 CONN HEADER 2P 2.5MM TOP BLUE SD 30009005 IC 24C16 PL106 30002362 CNAS 830 FAV SHL W/4C+FER 30024554 POWER CORD SAFE BSI 2.2M SHARP W/FLT-FUS PL107 30001839 CONN HEADER 3P 2.5MM TOP GREEN SD 30018270 TRANSFORMER PFC SAFE 1,7A 43MH 170W PL108 30020926 CNAS 3P/900 FLT W/BLK C UL2468AWG24 20150375 PR.IC.45-SHARP 1.2.67-L1...
Page 12
Technical information and Production: Vestel Electronik AS PRINTED BY: Think Ecology, please use Technical information re-issued: SHARP ELECTRONICA ESPAÑA S.A. Service Manual Group Engineering Dept. Polígono Industrial Can Sant Joan 08190 Sant Cugat del Vallès Barcelona...
Page 13
TABLE OF CONTENTS 1.INTRODUCTION.............................1 2.TUNER..............................1 3.IF PART (TDA9885/86)..........................1 4.VIDEO SWITCH TEA6415........................2 5.MULTI STANDARD SOUND PROCESSOR...................2 6.SOUND OUTPUT STAGE WITH TDA7269A..................2 7.BERTICAL OUTPUT STAGE WITH STV9379FA...................2 8.VIDEO OUTPUT AMPLIFIER TDA6108....................2 9.POWER SUPPLY (SMPS)........................3 10.MICROCONTROLLER SDA55XX......................3 10.1.General Features..........................3 10.2.External Crystal and Programmable Clock Speed................3 10.3.Microcontroller Features.........................3 10.4.Memory............................
1.INTRODUCTION 11AK45 is a 50Hz colour television capable of driving 24” + CRT sizes( beginning from 24” 16:9 up to 33”). The chassis is capable of operation in PAL, SECAM, NTSC (playback) colour standards and multiple transmission standards as B/G, D/K, I/I’, and L/L´. Sound system output is supplying 2x10W (10%THD) for left and right outputs of 8ohm speakers.
4.VIDEO SWITCH TEA6415 In case of three or more external sources are used, the video switch IC TEA6415 is used. The main function of this device is to switch 8 video-input sources on the 6 outputs. Each output can be switched on only one of each input. On each input an alignment of the lowest level of the signal is made (bottom of sync.
9.POWER SUPPLY (SMPS) The DC voltages required at various parts of the chassis are provided by an SMPS transformer controlled by the IC MC44608, which is designed for driving, controlling and protecting switching transistor of SMPS. The transformer generates 145V for FBT input, +/-14V for audio amplifier, 5V and 3.3V stand by voltage and 8V, 12V and 5V supplies for other different parts of the chassis.
• One out of Eight Colours for Foreground and Background Colours for 1-bit DRCS and ROM Characters • Shadowing • Contrast Reduction • Pixel by Pixel Shiftable Cursor With up to 4 Different Colours • Support of Progressive Scan and 100 Hz. •...
K9356M: Standard B/G, D/K, I, L Features TV IF audio filter with pass band for sound carriers at 32,40 MHz (D/K, L), 32,90 MHz (I) and 33,40 MHz (B/G) K3953M Terminal and Pin configuration are the same with K9656M: Standard B/G, D/K, I, L/L’...
• Low power consumption • Short-circuit resistant • High performance • high signal-to-noise ratio • High slew rate • Low distortion • Large output voltage swing. 13.2.3.Pinning SYMBOL DESCRIPTION OUTA Output A INA(neg) Inverting input A INA(pos) Non-inverting input A Negative supply INB(pos) Non-inverting input B...
13.3.2.Features Standard Selection with single I C transmission Automatic Standard Detection of terrestrial TV standards Automatic Sound Selection (mono/stereo/bilingual), new registers MODUS, STATUS Two selectable sound IF (SIF) inputs Automatic Carrier Mute function Interrupt output programmable (indicating status change) Loudspeaker / Headphone channel with volume, balance, bass, treble, loudness AVC: Automatic Volume Correction Subwoofer output with programmable low-pass and complementary high-pass filter 5-band graphic equalizer for loudspeaker channel...
AVSS Analog ground MONO_IN Mono input Not connected Reference voltage IF A/D VREFTOP converter SC1_IN_R SCART 1 input, right SC1_IN_L SCART 1 input, left ASG1 AHVSS Analog Shield Ground 1 SC2_IN_R SCART 2 input, right SC2_IN_L SCART 2 input, left ASG2 AHVSS Analog Shield Ground 2...
13.4.2.Features Video Decoding and Processing – four CVBS, one S-VHS input, one YC component input – integrated high-quality A/D converters and associated clamp and AGC circuits – adaptive 2H comb filter Y/C separator – multistandard colour decoder PAL/NTSC/SECAM including all substandards –...
• 6.5dB gain between any input and output • 55dB crosstalk at 5mHz • Fully ESD protected 13.5.3.Pinning Input Max : 2Vpp, Input Current: 1mA, Max : 3mA Data Low level : -0.3V Max: 1.5V, High level : 3.0V Max : Vcc+0.5V Input Max : 2Vpp, Input Current: 1mA, Max : 3mA Clock...
13.7.TDA7269A 13.7.1.Description The TDA7269A is class AB dual Audio power amplifier assembled in the Multiwatt package, specially designed for high quality sound application as Hi-Fi music centers and stereo TV sets. 13.7.2.Features Wide Supply Voltage Range Up To ±20V Split Supply High Output Power 14 + 14W @THD =10%, R =Ω,V...
• Self-timed Write Cycle (10 ms max) • High-reliability – Endurance: 1 Million Write Cycles – Data Retention: 100 Years • Automotive Grade and Extended Temperature Devices Available • 8-lead JEDEC SOIC, 8-pin PDIP and 8-lead TSSOP Packages 13.9.3.Pin Configurations Pin name Function A0-A2...
Memory • Non-multiplexed 8-bit data and 16 … 20-bit address bus (ROMless Version) • Memory banking up to 1Mbyte (Romless version) • Up to 128 Kilobyte on Chip Program ROM • Eight 16-bit data pointer registers (DPTR) • 256-bytes on-chip Processor Internal RAM (IRAM) •...
enables the reduction of the stand–by power consumption to approximately 1W while delivering 300mW in a 150W SMPS. • Integrated Start–Up Current Source • Lossless Off–Line Start–Up • Direct Off–Line Operation • Fast Start–Up 13.11.2.General Features • Flexibility • Duty Cycle Control •...
13.12.TCET1102G 13.12.1.Description The TCET110/ TCET2100/ TCET4100 consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4-lead up to 16-lead plastic dual inline package. The elements are mounted on one lead frame using a coplanar technique, providing a fixed distance between input and output for highest safety requirements.
AM demodulator without extra reference circuit Alignment-free selective FM-PLL demodulator with high linearity and low noise I C-bus control for all functions I C-bus transceiver with pin programmable Module Address (MAD). 13.13.3.Pinning SYMBOL DESCRIPTION VIF1 VIF differential input 1 VIF2 VIF differential input 2 output 1 (open-collector) FMPLL...
14.AK45 CHASSIS PRODUCTION SERVICE MODE ADJUSTMENTS 14.1.SERVICE MENU All system, geometry and white balance alignments are performed in production service mode. Before starting the production mode alignments, make sure that all manual adjustments are done correctly. To start production mode alignments enter the MAIN MENU and then press the digits 4, 7, 2 and 5 respectively or press MUTE and INFO buttons at the same time.
Page 35
Y-Delay NTSC Enter an NTSC colour and black-white bar test pattern via RF. Adjust Y-Delay NTSC till the colour transients on the colour bar of the pattern become as sharper and colours between transients do not mix with each other as possible. Y-Delay other Not used.
Page 36
The amplitude of B of RGB output can be adjusted with the drive parameter WDB. The DC offset values of R of RGB output can be adjusted with the cutoff parameter CR. The DC offset values of G of RGB output can be adjusted with the cutoff parameter CG. The DC offset values of B of RGB output can be adjusted with the cutoff parameter CB.
Page 37
PANORAMIC VERT_POS (Panoramic mode Vertical Position) It’s used to adjust the vertical position of panoramic mode. PANORAMIC VERT_AMPL (Panoramic mode Vertical Amplitude) It’s used to adjust the vertical amplitude of panoramic mode. PANORAMIC VERT_SCOR (Panoramic mode Vertical S-Correction) It’s used to adjust the vertical s-correction of panoramic mode. PANORAMIC VERT_SSYM (Panoramic mode Vertical S-Symmetry) It’s used to adjust the vertical s-symmetry of panoramic mode.
Page 38
16:9 ZOOM VERT_POS (16:9 Zoom mode Vertical Position) It’s used to adjust the vertical position of 16:9 zoom mode. 16:9 ZOOM VERT_AMPL (16:9 Zoom mode Vertical Amplitude) It’s used to adjust the vertical amplitude of 16:9 zoom mode. 16:9 ZOOM VERT_SCOR (16:9 Zoom mode Vertical S-Correction) It’s used to adjust the vertical s-correction of 16:9 zoom mode.
Page 39
OSD Position It’s used to adjust the horizontal position of the OSD. BCLTHR Beam current threshold BCLG Beam current loop gain ROTATION (TILT) This adjustment only works when the TV has rotation option. Change TILT by pressing Left/Right buttons to rotate the complete raster clock-wise and counter clock-wise depending on the CRT. Check and readjust TRPEZ item if the adjustment becomes improper after some other geometric adjustments are done.
Page 40
POFS2 (RGB HORIZONTAL SHIFT) It’s used to adjust the horizontal position of RGB signal. REFERENCE WDR RED COOL The amplitude of R of RGB output can be adjusted with the drive parameter WDR for the colour temp of cool mode. REFERENCE WDR GREEN COOL The amplitude of G of RGB output can be adjusted with the drive parameter WDR for the colour temp of cool mode.
Page 41
FULL HORZ_POS It’s used to adjust the horizontal position of 16:9 mode (full mode). FULL HORZ_AMPL It’s used to adjust the horizontal amplitude of 16:9 mode (full mode). BRIGHT MODE BRIGHTNESS It’s used to adjust the brightness value of bright mode. BRIGHT MODE COLOUR It’s used to adjust the colour value of bright mode.
Page 42
14:9 RGB CUSHION It’s used to adjust the cushion in 14:9 mode for RGB signals. PANAROMIC RGB HORIZONTAL AMPLITUDE It’s used to adjust the horizontal amplitude in panoramic mode for RGB signals. 16:9 RGB HORIZANTOL AMPLITUDE It’s used to adjust the horizontal amplitude in 16:9 mode for RGB signals. 16:9 SUBTITLE RGB HORIZONTAL AMPLITUDE It’s used to adjust the horizontal amplitude in 16:9 subtitle mode for RGB signals.
Page 43
ADJUST EXPLANATION 2835 2835W MULTI MULTI - PAL I White Point RED White Point GREEN Whit Point BLUE AGC (Automatic Gain Control) It will be adjusted to below 1V of Max. AGC for each TV. IF-PLL Negative IF-PLL Positive Y-Delay Y-Delay SECAM Y-Delay NTSC Y-Delay OTHER...
14.3.OPTIONS MENU Select the parameter by pressing up/down buttons. Adjust the parameter by pressing Left/Right buttons. . In OPTIONS menu, some of the changed parameters are not stored automatically. To store the adjusted parameters, you should turn off and on TV. OPTIONS...
B2: x B1: LUMA 1 Luma Soft Limiter Enabled B0: BB 1 Blue Background Option Option 3. (0x19) Video Processor Cathode Drive Level B7: x B6: x B5: x B4: x B3: x B2: x B1: x B0: country note 0 Note 0: choice for others country option Option 4.
Option 8. IF Frequency B7: x B6: x B5: IfI note 3 B4: IfD note 4 B3: IfM note 5 B2: Aps note 6 B1: Hp note 7 B0: Hue note 8 note 3: IF I 39.5 MHz Great Britain I , Only UHF Tuner IF I 38.9 MHz Ireland I+ Standard Tuner...
B0: BSVHS = note 6 note 2 : RGB Menu Item active/inactive RGB Menu Item inactive RGB Menu Item active note 3: Front S-VHS not supported Front S-VHS available note 4: Back AV (AV-3) not supported Back AV (AV-3) available note 5: Scart 2 not supported Scart 2 available...
Equalizer available Equalizer not available Equalizer available note 5 : List Mode available List Mode not available List Mode available note 6 : Country Line available / Aps available or not Country Line not available / Aps not available Country Line available / Aps available note 7 : VCR Menu Item available / not available VCR Menu Item not available...
Option 55. Speaker Setup b7 b6 b5 b4 b3 b2 b1 b0 Speaker Setup (L/R, L/C/R, L/R/S, L/C/R/S) 0 0 0 0 0 0 0 0 Option 56. Audio Options Available Or Not Attention: All bits on the Option 56 must be the “0” for MONO TV SETS B7: nicam note 7 B6: ASD...
14.4.OPTION TABLE RECOMMENDED VALUES X listed in the option can be 0 or 1 OPTION 2835 MULTI 2835W MULTI 2835W PAL I X2 XXXXXX10 X2 XXXXXX10 X2 XXXXXX10 XX XXXXXXXX XX XXXXXXXX XX XXXXXXXX 001XXX11 23 001XXX11 23 001XXX11 XX XXXXXXX0 XX XXXXXXX0 XX XXXXXXX0 XX XXXXXXXX...
14.5.SCREEN ADJUSTMENT (FBT SCREEN) SCREEN ADJUST From the option list change option 2 bit 6 from 0 to 1 for disabling vertical scan. Adjust horizontal line via screen adjust pot. as thin as possible. Then press 0 to leave service menu. AK45 Service Manual 17/12/2007...
16.BLOCK DIAGRAM GENERAL BLOCK DIAGRAM OF CHASSIS 11 AK 45 SC3_V_OUT RGB AMPLIFIER TDA 6107 CVBS (PHILIPS) SC1_V_OUT TDA9885T K3958M V id e o EPCOS TU200 Filter 38.9MHz-TV TUNER VDP313XY S ou nd K9656M EPCOS Filter Vertical Stage Y o k e Horizontal STV9379FA SC1_RGB...