Grundig 28 VLE 5700 WN User Instructions page 58

SPECIAL­SETTINGS
DiSEqC­1.2­Settings
You can adjust the alignment of the satellite an-
tenna to each individual satellite. These settings
will be saved so that the antenna can later be
easily guided to each saved alignment.
1 Select the line »DiSEqC 1.2 SETTINGS« with
» « or » « and press »OK« to confirm.
V Λ
– T he »DiSEqC 1.2 SETTINGS« menu ap-
pears.
2 Select the preferred option with »
or » «.
Λ
– » Transponder«: »Press OK«, select the
transponder from which the signal is being
r eceived with »
press »OK« to confirm.
– » Moving Mode«: Use »
the option »Discrete« or »Continuous«.
– » Discrete«: Moves the antenna in
d efined steps to the west and the east.
– » Continuous«: Moves the antenna to the
west or east continuously.
– » Step Size«: Use »
number of steps with which the antenna
should turn. »Step Size« is only active
when the »Transport Mode« was set to
»Discrete«.
– » Move Motor«: Aligns the antenna with
the selected satellite. Use »
»West«, use »
– » Go To Stored Position«: Aligns the antenna
to a saved satellite position. Up to 50 posi-
tions can be saved. »Press OK« and then
select the saved position with »
Press » « (green) to confirm – the anten-

na will be aligned with the saved position.
– » Store Stored Position«: The current anten-
na alignment is saved.
– » Limit Position«: Defines the range in
which the antenna may move. Use »
to set the western limit, use »
eastern limit.
– » Reset DiSEqC 1.2 Limit«: Resets the limit
position of the antenna.
3 Press »EXIT« to end the setting.
­ 5 8
ENGLISH
­ - ---------------------------------------------------------------------------------------------------------
< >
«, » «, » « or »
V Λ
< >
« or » « to select
< >
« or » « to select the
<
« to align it to
>
« to align it to »East«.
<
« or »
>
« to set the
Searching­for­television­chan-
nels­from­the­cable­provider­
automatically
1 Open the menu with »MENU«.
2 Select the menu item »SOURCE SETUP« with
» « or »
V
– T he »SOURCE SETUP« menu appears.
3 Select the line »Source« with »
or » « and press »OK« to confirm.
Λ
«
V
Select the option »Cable« with »
» « or »
V
4 Select the line »Automatic Channel Search«
with »
« and
V
– T he menu appears.
Connection Type
Country
Scan Type
Cable Scan Type
Frequency (MHz)
Network ID
>
«.
5 Select the line »Scan Typ« with »
and set the option »DTV« with »
6 Select the line »Cable Scan Type« with »
or » « and set the option »Quick« or »Full«
Λ
<
with »
<
«
– T he search function »Quick« sets the channels
according to the information provided by your
cable provide in the transmission signal.
– I f the option »Full« is selected, the entire fre-
quency range will be scanned. The search
can take a long time with this option. This
option is recommended if your cable pro-
vider does not support the search type
»Quick«.
« and press »OK« to confirm.
Λ
« and press »OK« to confirm.
Λ
« or » « and press »OK« to confirm.
Λ
SOURCE SETUP
AUTOMATIC CHANNEL
Exit
Back
>
« or » «.
«
V
< >
«, » «,
08.08.2012
15:46
SEARCH
Cabel
U.K.
DTV & ATV
Quick
Auto
Auto
Start Search
« or » «
V Λ
< >
« or » «.
«
V