Gestetner P7675 Supplementary Manual

Gestetner p7675: supplementary guide
Hide thumbs Also See for P7675:

Advertisement

Quick Links

Introduction
This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.
Power Source
220-240 V, 50/60 Hz, 10 A
Please be sure to connect the power cable to a power source as above.
Laser Safety:
This machine is considered a class 1 laser device, safe for office/EDP use. The machine contains four
AlGalnp laser diodes, 10-milliwatt, 770-810 nanometer wavelength for each emitter. Direct (or indirect
reflected ) eye contact with the laser beam might cause serious eye damage. Safety precautions and
interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.
The following label is attached on rear side of the printer.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Do not copy or print any item for which reproduction is prohibited by law.
Copying or printing the following items is generally prohibited by local law:
bank notes, revenue stamps, bonds, stock certificates, bank drafts, checks, passports, driver's licenses.
The preceding list is meant as a guide only and is not inclusive. We assume no responsibility for its
completeness or accuracy. If you have any questions concerning the legality of copying or printing cer-
tain items, consult with your legal advisor.
Two kinds of size notation are employed in this manual. With this machine refer to the metric version.
For good print quality, the supplier recommends that you use genuine toner, maintenance kits and parts
from the supplier.
The supplier shall not be responsible for any damage or expense that might result from the use of con-
sumables (toner, maintenance kits and parts) other than genuine consumables from the supplier with
your office products.
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.

Advertisement

Table of Contents
loading

Summary of Contents for Gestetner P7675

  • Page 1 ) eye contact with the laser beam might cause serious eye damage. Safety precautions and interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator. The following label is attached on rear side of the printer. Important Contents of this manual are subject to change without prior notice.
  • Page 2: Safety Information

    Safety Information When using your printer, the following safety precautions should always be fol- lowed. In this manual, the following important symbols are used: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
  • Page 3 • If smoke is coming out, there is a strange smell, or anything looks un- usual, immediately turn off the power switch of the machine, such as the main power switch, and then unplug the machine from the outlet. Otherwise, it could cause an electric shock or fire. Next, contact your sales or service representative.
  • Page 4 • The inside of this printer becomes very hot. Do not touch parts labelled “v” (indicating a hot surface). Touching these parts will result in burns. • Do not push or pull the call-light when installed to the printer. Doing so may result in damage or malfunction of the call-light or the printer.
  • Page 5 Positions of RWARNING and RCAUTION labels This machine has labels for RWARNING and RCAUTION at the positions shown below. For safety, please follow the instructions and handle the machine as indicated. AST006S...
  • Page 6 The inside of this printer becomes very hot. Do not touch parts with this label (indicating a hot surface). Touching these parts will result in burns. Do not touch this section of the machine. It could cause injury. Do not touch this section of the machine. It could cause injury.
  • Page 7: User Information On Electrical & Electronic Equipment

    User Information on Electrical & Electronic Equipment Users in the EU, Switzerland and Norway Our Products contain high quality components and are designed to facilitate re- cycling. Our products or product packaging are marked with the symbol below. The symbol indicates that the product must not be treated as municipal waste. It must be disposed of separately via the appropriate return and collection sys- tems available.
  • Page 8: Noise Emission

    Noise Emission ❖ Sound Power Level Standby During Printing ❖ Sound Pressure level Standby During Printing The preceding measurements made in accordance with ISO7779 are actual values. Measured at the position of a bystander. Main unit only 51 dB (A) 71 dB (A) Main unit only 44 dB (A)
  • Page 9: Energy Star Program

    Low-power mode. ❖ Low-power Mode (Energy Saver mode) This printer automatically lowers its power consumption 60 minutes after the last operation has been completed. To exit Low-power (Energy Saver) mode, press any key on the control panel. For more information about how to con- figure Energy Saver mode, see “Making Printer Settings with Control Panel”,...
  • Page 10 MEMO...
  • Page 11 MEMO...
  • Page 12 In accordance with IEC 60417, this machine uses the following symbols for the main switch: a means POWER ON. c means STAND BY. Declaration of Conformity “The Product complies with the requirements of the EMC Directive 89/336/EEC and its amending di- rectives and the Low Voltage Directive 73/23/EEC and its amending directives.”...

Table of Contents